Infiniti EX35. Manual — part 311
BR-6
< PREPARATION >
PREPARATION
PREPARATION
PREPARATION
Commercial Service Tool
INFOID:0000000003139967
Tool name
Description
Power tool
Loosening bolts and nuts
PBIC0190E
BRAKE PEDAL
BR-7
< ON-VEHICLE MAINTENANCE >
C
D
E
G
H
I
J
K
L
M
A
B
BR
N
O
P
ON-VEHICLE MAINTENANCE
BRAKE PEDAL
Inspection and Adjustment
INFOID:0000000003562162
INSPECTION
Brake Pedal Height
Check the brake pedal height (H
1
) between the dash lower panel (1)
and the brake pedal upper surface.
CAUTION:
Remove the floor trim.
Stop Lamp Switch and ASCD Brake Switch
Check the clearance (C) between stopper rubber (1) and stop lamp
switch and ASCD brake switch (2) threaded end.
CAUTION:
The stop lamp must be turned off when the brake pedal is
released.
NOTE:
Pull the brake pedal pad to make the clearance between stopper
rubber and stop lamp switch and ASCD brake switch threaded end.
Brake Pedal Play
Press the brake pedal. Check the brake pedal play (A).
Depressed Brake Pedal Height
Check the brake pedal height (H
2
) between the dash lower panel (1)
and the brake pedal upper surface when depressing the brake pedal
at 490 N (50 kg, 110 lb) while turning engine ON.
CAUTION:
Remove the floor trim.
Standard
H
1
: Refer to
JPFIA0065ZZ
Standard
C
: Refer to
.
JPFIA0122ZZ
Standard
A
: Refer to
.
JPFIA0121ZZ
Standard
H
2
: Refer to
.
JPFIA0068ZZ
BR-8
< ON-VEHICLE MAINTENANCE >
BRAKE PEDAL
ADJUSTMENT
Brake Pedal Height
1.
Remove instrument lower panel LH. Refer to
2.
Disconnect the stop lamp switch and ASCD brake switch harness connector.
3.
Turn the stop lamp switch and ASCD brake switch 45
°
counterclockwise.
4.
Loosen the input rod lock nut (1). Adjust the brake pedal height
(H
1
) to the specification. Tighten the input rod lock nut to the
specification. Refer to
.
CAUTION:
The threaded end of the input rod (2) must project to the
inner side (L) of the clevis (3).
Stop Lamp Switch and ASCD Brake Switch
1.
Remove instrument lower panel LH. Refer to
2.
Disconnect the stop lamp switch and ASCD brake switch harness connector.
3.
Turn the stop lamp switch and ASCD brake switch 45
°
counterclockwise.
4.
Press-fit stop lamp switch and ASCD brake switch (2) until stop
lamp switch and ASCD brake switch hits the stopper rubber (1)
45
°
clockwise.
CAUTION:
• The clearance (C) between the stopper rubber and stop
lamp switch and ASCD brake switch threaded end must
be the specified value. Refer to
.
• The stop lamp must be turned off when the brake pedal is
released.
Brake Pedal Play
1.
Remove instrument lower panel LH. Refer to
2.
Disconnect the stop lamp switch and ASCD brake switch harness connector.
3.
Turn the stop lamp switch and ASCD brake switch 45
°
counterclockwise.
JPFIA0003ZZ
Standard
H
1
: Refer to
.
JPFIA0279ZZ
JPFIA0122ZZ
BRAKE PEDAL
BR-9
< ON-VEHICLE MAINTENANCE >
C
D
E
G
H
I
J
K
L
M
A
B
BR
N
O
P
4.
Press-fit stop lamp switch and ASCD brake switch (2) until stop
lamp switch and ASCD brake switch hits the stopper rubber (1)
45
°
clockwise.
CAUTION:
• The clearance (C) between the stopper rubber and stop
lamp switch and ASCD brake switch threaded end must
be the specified value. Refer to
.
• The stop lamp must be turned off when the brake pedal is
released.
JPFIA0122ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст