Infiniti EX35. Manual — part 508
DLK-246
< ON-VEHICLE REPAIR >
[INTELLIGENT KEY SYSTEM]
FRONT DOOR LOCK
10. While pulling outside handle bracket, slide toward rear of vehicle
to remove outside handle bracket.
11. Reach in to separate outside handle cable connection on outside handle bracket.
12. Remove door lock assembly TORX bolts.
13. Disconnect door lock actuator connector, and then remove door lock assembly.
14. Remove key rod from door lock assembly.
INSTALLATION
Install in the reverse order of removal.
CAUTION:
• When installing each rod, rotate rod holder until a click is felt.
• Check door open/close, lock/unlock operation after installation.
INSIDE HANDLE
INSIDE HANDLE : Exploded View
INFOID:0000000003691280
: Pawl
JMKIA2302ZZ
1.
Door key cylinder assembly (driver
side)
Outside handle escutcheon (passen-
ger side)
2.
Rear gasket
3.
TORX bolt
4.
Key rod (driver side)
5.
Door lock assembly
6.
Inside handle
7.
Outside handle bracket
8.
Front gasket
9.
Outside handle
JMKIA2053GB
FRONT DOOR LOCK
DLK-247
< ON-VEHICLE REPAIR >
[INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
INSIDE HANDLE : Removal and Installation
INFOID:0000000003556367
REMOVAL
1.
Remove front door finisher. Refer to
INT-11, "DRIVER SIDE : Removal and Installation"
(driver side) or
INT-14, "PASSENGER SIDE : Removal and Installation"
(passenger side).
2.
Disconnect inside handle cable, and then remove the inside handle.
3.
Remove inside handle mounting screws.
INSTALLATION
Install in the reverse order of removal.
CAUTION:
Check door open/close, lock/unlock operation after installation.
OUTSIDE HANDLE
OUTSIDE HANDLE : Exploded View
INFOID:0000000003691281
OUTSIDE HANDLE : Removal and Installation
INFOID:0000000003556369
REMOVAL
: Vehicle front
Refer to
1.
Door key cylinder assembly (driver
side)
Outside handle escutcheon (passen-
ger side)
2.
Rear gasket
3.
TORX bolt
4.
Key rod (driver side)
5.
Door lock assembly
6.
Inside handle
7.
Outside handle bracket
8.
Front gasket
9.
Outside handle
: Vehicle front
Refer to
JMKIA2053GB
DLK-248
< ON-VEHICLE REPAIR >
[INTELLIGENT KEY SYSTEM]
FRONT DOOR LOCK
1.
Remove front door finisher. Refer to
INT-11, "DRIVER SIDE : Removal and Installation"
(driver side) or
INT-14, "PASSENGER SIDE : Removal and Installation"
(passenger side).
2.
Remove front door glass. Refer to
GW-17, "Removal and Installation"
3.
Remove front door module assembly. Refer to
GW-20, "Removal and Installation"
.
4.
Disconnect door antenna and door request switch connector and remove harness clamp (models with
Intelligent Key system) on outside handle bracket.
5.
Remove door side grommet, and loosen TORX bolt from grom-
met hole.
CAUTION:
Never remove TORX bolt forcibly.
6.
Reach in to separate key rod (2) connection [on the door key
cylinder assembly (1)] (driver side).
7.
While pulling outside handle, remove door key cylinder assem-
bly (driver side) or outside handle escutcheon (passenger side).
8.
While pulling outside handle (1), slide toward rear of vehicle to
remove outside handle.
9.
Remove front gasket and rear gasket.
: TORX bolt
JMKIA2094ZZ
JMKIA0553ZZ
JMKIA0560ZZ
JMKIA0524ZZ
FRONT DOOR LOCK
DLK-249
< ON-VEHICLE REPAIR >
[INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
10. While pulling outside handle bracket, slide toward rear of vehicle
to remove outside handle bracket.
11. Reach in to separate outside handle cable connection on outside handle bracket.
INSTALLATION
Install in the reverse order of removal.
CAUTION:
• When installing each rod, rotate rod holder until a click is felt.
• Check door open/close, lock/unlock operation after installation.
: Pawl
JMKIA2302ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст