Infiniti EX35. Manual — part 787
EXL-192
< ON-VEHICLE REPAIR >
[XENON TYPE]
FRONT COMBINATION LAMP
ON-VEHICLE REPAIR
FRONT COMBINATION LAMP
Exploded View
INFOID:0000000003135395
REMOVAL
DISASSEMBLY
1.
Front combination lamp
JPLIA0916ZZ
1.
Front side marker lamp bulb
2.
Front side marker lamp bulb socket
3.
Front turn signal lamp bulb socket
4.
Front turn signal lamp bulb
5.
Xenon bulb
6.
Xenon bulb socket
7.
Seal packing
8.
Resin cap
9.
Headlamp (HI) bulb
10.
Seal packing
11. HID control unit
12. Bumper bracket
13.
Headlamp housing assembly
14. Parking lamp bulb
15. Parking lamp bulb socket
16.
Retaining spring
Refer to
for symbols not described above.
JPLIA0917ZZ
FRONT COMBINATION LAMP
EXL-193
< ON-VEHICLE REPAIR >
[XENON TYPE]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
Removal and Installation
INFOID:0000000003135396
REMOVAL
CAUTION:
Disconnect the battery negative terminal or remove the fuse.
1.
Remove the front bumper fascia. Refer to
.
2.
Remove the headlamp mounting bolts and clips.
3.
Remove the harness clip and the holding clip (A)
*
.
*: Left side only.
4.
Pull out the headlamp assembly forward the vehicle.
5.
Disconnect the connector before removing the headlamp
assembly.
INSTALLATION
Install in the reverse order of removal.
NOTE:
After installation, perform aiming adjustment. Refer to
.
Replacement
INFOID:0000000003135397
CAUTION:
• Disconnect the battery negative terminal or remove the fuse.
• After installing the bulb, install the resin cap and the bulb socket securely for watertightness.
• Never touch the glass of bulb directly by hand. Keep grease and other oily matters away from it.
Never touch bulb by hand while it is lit or right after being turned off.
• Never leave bulb out of lamp reflector for a long time because dust, moisture smoke, etc. may affect
the performance of lamp. When replacing bulb, be sure to replace it with new one.
HEADLAMP BULB (LO)
1.
Remove the fender rubber protector in the engine room. Keep a service area.
2.
Rotate the resin cap counterclockwise and unlock it.
3.
Rotate the bulb socket counterclockwise and unlock it.
4.
Remove the retaining spring lock. And then remove the bulb
from the headlamp housing assembly.
CAUTION:
Never break the xenon bulb ceramic tube when replacing
the bulb.
HEADLAMP BULB (HI)
1.
Remove the washer tank inlet
*
*:When replace a right.
2.
Disconnect the headlamp (HI) bulb connector.
3.
Rotate the bulb socket counterclockwise and unlock it.
4.
Remove the bulb socket from the headlamp housing assembly.
PARKING LAMP BULB
1.
Rotate the bulb socket counterclockwise and unlock it.
: Vehicle front
JPLIA0918ZZ
JPLIA0919ZZ
EXL-194
< ON-VEHICLE REPAIR >
[XENON TYPE]
FRONT COMBINATION LAMP
2.
Remove the bulb from the bulb socket.
FRONT TURN SIGNAL LAMP BULB
1.
Remove the fender rubber protector in the engine room. Keep a service area.
2.
Rotate the bulb socket counterclockwise and unlock it.
3.
Remove the bulb from the bulb socket.
FRONT SIDE MARKER LAMP BULB
1.
Remove the fender rubber protector in the engine room. Keep a service area.
2.
Rotate the bulb socket counterclockwise and unlock it.
3.
Remove the bulb from the bulb socket.
Disassembly and Assembly
INFOID:0000000003135398
DISASSEMBLY
1.
Rotate the resin cap counterclockwise and unlock it.
2.
Rotate the xenon bulb socket counterclockwise and unlock it.
3.
Remove the retaining spring lock. Remove the xenon bulb.
4.
Remove the bumper bracket.
5.
Remove the HID control unit installation screw.
6.
Remove the screw. Disconnect the connector from HID control unit.
7.
Pull out the xenon bulb socket from the headlamp housing assembly.
8.
Rotate the parking lamp bulb socket counterclockwise and unlock it.
9.
Remove the bulb from the parking lamp bulb socket.
10. Rotate the front turn signal lamp bulb socket counterclockwise and unlock it.
11. Remove the bulb from the front turn signal lamp bulb socket.
12. Rotate the front side marker lamp bulb socket counterclockwise and unlock it.
13. Remove the bulb from the front side marker lamp bulb socket.
14. Rotate the headlamp (HI) bulb socket counterclockwise and unlock it.
15. Remove the bulb socket from the headlamp housing assembly.
ASSEMBLY
Assemble in the reverse order of disassembly.
CAUTION:
• Install HID control unit securely.
• After installing the bulb, install the resin cap and the bulb socket securely for watertightness.
• Seal packing cannot be reused.
FRONT FOG LAMP
EXL-195
< ON-VEHICLE REPAIR >
[XENON TYPE]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
FRONT FOG LAMP
Exploded View
INFOID:0000000003552491
Removal and Installation
INFOID:0000000003552492
CAUTION:
Disconnect the battery negative terminal or remove the fuse.
REMOVAL
1.
Remove the front fender protector. Keep a service area. Refer to
.
2.
Remove the front fog lamp finisher.
3.
Remove the front fog lamp connector.
4.
Remove the screw.
5.
Disengage the pawl. And then remove the front fog lamp.
INSTALLATION
Installation is the reverse order of removal.
NOTE:
After installation, perform aiming adjustment. Refer to
Replacement
INFOID:0000000003552493
CAUTION:
• Disconnect the battery negative terminal or remove the fuse.
• Never touch the glass of bulb directly by hand. Keep grease and other oily matters away from it.
Never touch bulb by hand while it is lit or right after being turned off.
• Never leave bulb out of lamp reflector for a long time because dust, moisture smoke, etc. may affect
the performance of lamp. When replacing bulb, be sure to replace it with new one.
FRONT FOG LAMP BULB
1.
Remove the front fender protector. Keep the service area. Refer to
.
1.
Front fog lamp
2.
Front fog lamp finisher
: Pawl
JPLIA0920ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст