Infiniti EX35. Manual — part 1294
SEC-72
< COMPONENT DIAGNOSIS >
[INTELLIGENT KEY SYSTEM]
B2607 STEERING LOCK RELAY
3.
CHECK STEERING LOCK UNIT CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect IPDM E/R connector E5.
3.
Check continuity between steering lock unit harness connector and IPDM E/R harness connector.
4.
Check continuity between steering lock unit harness connector and ground.
Is the inspection result normal?
YES
>> Replace IPDM E/R. Refer to
PCS-34, "Removal and Installation"
NO
>> Repair or replace harness or connector.
4.
CHECK INTERMITTENT INCIDENT
GI-38, "Intermittent Incident"
>> INSPECTION END
Steering lock unit
IPDM E/R
Continuity
Connector
Terminal
Connector
Terminal
M40
1
E5
11
Existed
Steering lock unit
Ground
Continuity
Connector
Terminal
M40
1
Not existed
B2608 STARTER RELAY
SEC-73
< COMPONENT DIAGNOSIS >
[INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
SEC
N
O
P
B2608 STARTER RELAY
Description
INFOID:0000000003586567
Located in IPDM E/R, it runs the starter motor. The starter relay is turned ON by the BCM when the ignition
switch is in START position. IPDM E/R transmits the starter relay ON signal to BCM via CAN communication.
DTC Logic
INFOID:0000000003586568
DTC DETECTION LOGIC
NOTE:
• If DTC B2608 is displayed with DTC U1000, first perform the trouble diagnosis for DTC U1000. Refer to
• If DTC B2608 is displayed with DTC U1010, first perform the trouble diagnosis for DTC U1010. Refer to
• If DTC B2608 is displayed with DTC B210D for IPDM E/R, first perform the trouble diagnosis for DTC
B210D. Refer to
DTC CONFIRMATION PROCEDURE
1.
PERFORM DTC CONFIRMATION PROCEDURE
1.
Press the push-button ignition switch under the following conditions.
-
Selector lever is in the P or N position.
-
Do not depress brake pedal.
2.
Check “Self diagnostic result” with CONSULT-III.
Is DTC detected?
YES
>> Go to
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000003586569
1.
CHECK BCM POWER SUPPLY CIRCUIT
1.
Turn ignition switch ON.
2.
Check voltage between BCM harness connector and ground.
Is the measurement value within the specification?
YES
>> GO TO 3.
NO
>> GO TO 2.
2.
CHECK STARTER RELAY CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect BCM connector M121 and IPDM E/R connector E6.
3.
Check continuity between IPDM E/R harness connector and BCM harness connector.
DTC No.
Trouble diagnosis
name
DTC detecting condition
Possible cause
B2608
STARTER RELAY
BCM receives starter relay ON signal (CAN) from
IPDM E/R even if BCM turns the starter relay OFF.
• Harness or connectors
(starter relay circuit is open or
shorted.)
• IPDM E/R
(+)
(–)
Condition
Voltage (V)
(Approx.)
BCM
Connector
Terminal
M121
52
Ground
Selector lever
N or P position
Battery voltage
Other than above
0
SEC-74
< COMPONENT DIAGNOSIS >
[INTELLIGENT KEY SYSTEM]
B2608 STARTER RELAY
4.
Check continuity between IPDM E/R harness connector and ground.
Is the inspection result normal?
YES
>> Replace IPDM E/R. Refer to
PCS-34, "Removal and Installation"
NO
>> Repair or replace harness or connector.
3.
CHECK INTERMITTENT INCIDENT
GI-38, "Intermittent Incident"
>> INSPECTION END
IPDM E/R
BCM
Continuity
Connector
Terminal
Connector
Terminal
E6
46
M121
52
Existed
IPDM E/R
Ground
Continuity
Connector
Terminal
E6
46
Not existed
B2609 STEERING STATUS
SEC-75
< COMPONENT DIAGNOSIS >
[INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
SEC
N
O
P
B2609 STEERING STATUS
Description
INFOID:0000000003586570
There are 2 switches in the steering lock unit (steering lock/unlock switch 1 and 2). BCM compares those 2
switches conditions to judge the present steering status.
DTC Logic
INFOID:0000000003586571
DTC DETECTION LOGIC
NOTE:
• If DTC B2609 is displayed with DTC U1000, first perform the trouble diagnosis for DTC U1000. Refer to
• If DTC B2609 is displayed with DTC U1010, first perform the trouble diagnosis for DTC U1010. Refer to
DTC CONFIRMATION PROCEDURE
1.
PERFORM DTC CONFIRMATION PROCEDURE 1
1.
Press the push-button ignition switch under the following conditions and wait for at least 1 second.
-
Selector lever is in the P or N position.
-
Do not depress brake pedal.
2.
Check “Self diagnostic result” with CONSULT-III.
Is DTC detected?
YES
>> Go to
NO
>> GO TO 2.
2.
PERFORM DTC CONFIRMATION PROCEDURE 2
1.
Turn ignition switch ON.
2.
Turn ignition switch OFF.
3.
Press driver side door switch and wait for at least 1 second.
4.
Check “Self diagnostic result” with CONSULT-III.
Is DTC detected?
YES
>> Go to
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000003586572
1.
INSPECTION START
Check the case in which DTC is detected.
• Case1: It is detected after ignition switch is changed from OFF to ON
• Case2: It is detected after ignition switch is changed from ON to OFF and door switch is pressed
In which case is DTC detected?
Case1 >> GO TO 2.
Case2 >> GO TO 6.
2.
CHECK BCM OUTPUT SIGNAL
1.
Turn ignition switch OFF.
DTC No.
Trouble diagnosis
name
DTC detecting condition
Possible cause
B2609
STEERING STATUS
BCM detects the malfunction of steering lock unit
switches for 1 second.
• Harness or connectors
[steering lock unit circuit (BCM
side) is open or shorted]
• Harness or connectors
[steering lock unit circuit (IPDM E/
R side) is open or shorted.]
• Steering lock unit
• IPDM E/R
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст