Infiniti EX35. Manual — part 295
BCS
DIAGNOSIS SYSTEM (BCM)
BCS-27
< FUNCTION DIAGNOSIS >
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
ACTIVE TEST
PRMT ENG STRT
Indicates [SET/RESET] condition of engine start possibility.
PRMT RKE STRT
NOTE:
This item is displayed, but cannot be monitored.
KEY SW -SLOT
Indicates [ON/OFF] condition of key slot.
TRNK/HAT MNTR
NOTE:
This item is displayed, but cannot be monitored.
RKE-LOCK
Indicates [ON/OFF] condition of LOCK signal from Intelligent Key.
RKE-UNLOCK
Indicates [ON/OFF] condition of UNLOCK signal from Intelligent Key.
RKE-TR/BD
NOTE:
This item is displayed, but cannot be monitored.
RKE-PANIC
Indicates [ON/OFF] condition of PANIC button of Intelligent Key.
RKE-P/W OPEN
Indicates [ON/OFF] condition of P/W DOWN signal from Intelligent Key.
RKE-MODE CHG
Indicates [ON/OFF] condition of MODE CHANGE signal from Intelligent Key.
RKE OPE COUN1
When remote keyless entry receiver receives the signal transmitted while operating on In-
telligent Key, the numerical value start changing.
RKE OPE COUN2
NOTE:
This item is displayed, but cannot be monitored.
Monitor Item
Condition
Test item
Description
BATTERY SAVER
This test is able to check interior room lamp operation.
The interior room lamp will be activated after “ON” on CONSULT-III screen is touched.
PW REMOTO DOWN SET
This test is able to check power window down operation.
The power window down will be activated after “ON” on CONSULT-III screen is touched.
INSIDE BUZZER
This test is able to check warning chime in combination meter operation.
• Take away warning chime sounds when “TAKE OUT” on CONSULT-III screen is touched.
• Key warning chime sounds when “KEY WARN” on CONSULT-III screen is touched.
• P position warning chime sounds when “P RNG WARN” on CONSULT-III screen is touched.
• ACC warning chime sounds when “ACC WARN” on CONSULT-III screen is touched.
OUTSIDE BUZZER
This test is able to check Intelligent Key warning buzzer operation.
The Intelligent Key warning buzzer will be activated after “ON” on CONSULT-III screen is
touched.
INDICATOR
This test is able to check warning lamp operation.
• “KEY” Warning lamp illuminates when “RED ON” on CONSULT-III screen is touched.
• “KEY” Warning lamp flashes when “RED IND” on CONSULT-III screen is touched.
INT LAMP
This test is able to check interior room lamp operation.
The interior room lamp will be activated after “ON” on CONSULT-III screen is touched.
LCD
This test is able to check meter display information
• Engine start information displays when “B&P N” on CONSULT-III screen is touched.
• Engine start information displays when “B&P I” on CONSULT-III screen is touched.
• Key ID warning displays when “ID NG” on CONSULT-III screen is touched.
• Steering lock information displays when “ROTAT” on CONSULT-III screen is touched.
• P position warning displays when “SFT P” on CONSULT-III screen is touched.
• Intelligent Key insert information displays when “INSRT” on CONSULT-III screen is touched.
• Intelligent Key low battery warning displays when “BATT” on CONSULT-III screen is
touched.
• Take away through window warning displays when “NO KY” on CONSULT-III screen is
touched.
• Take away warning display when “OUTKY” on CONSULT-III screen is touched.
• OFF position warning display when “LK WN” on CONSULT-III screen is touched.
TRUNK/GLASS HATCH
This test is able to check back door opener actuator open operation.
This actuator opens when “ON” on CONSULT-III screen is touched.
FLASHER
This test is able to check security hazard lamp operation.
The hazard lamps will be activated after “ON” on CONSULT-III screen is touched.
BCS-28
< FUNCTION DIAGNOSIS >
DIAGNOSIS SYSTEM (BCM)
COMB SW
COMB SW : CONSULT-III Function (BCM - COMB SW)
INFOID:0000000003534210
DATA MONITOR
HORN
This test is able to check horn operation.
The horn will be activated after “ON” on CONSULT-III screen is touched.
IGN CONT2
This test is able to check ignition relay operation.
The ignition relay will be activated after “ON” on CONSULT-III screen is touched.
P RANGE
This test is able to check control device power supply
Control device power is supplied when “ON” on CONSULT-III screen is touched.
ENGINE SW ILLUMI
This test is able to check push-ignition switch illumination operation.
Push-ignition switch illumination illuminates when “ON” on CONSULT-III screen is touched.
LOCK INDICATOR
NOTE:
This item is displayed, but cannot be tested.
ACC INDICATOR
This test is able to check indicator in push-ignition switch operation.
Indicator in push-ignition switch illuminates when “ON” on CONSULT-III screen is touched.
IGNITION ON IND
This test is able to check indicator in push-ignition switch operation.
Indicator in push-ignition switch illuminates when “ON” on CONSULT-III screen is touched.
KEY SLOT ILLUMI
This test is able to check key slot illumination operation.
Key slot illumination flash when “ON” on CONSULT-III screen is touched.
AUTOMATIC BACK DOOR
NOTE:
This item is displayed, but cannot be tested.
AUTOMATIC SLIDING DOOR
NOTE:
This item is displayed, but cannot be tested.
Test item
Description
Monitor item [UNIT]
Description
FR WIPER HI
[Off/On]
Displays the status of the FR WIPER HI switch in combination switch judged by BCM with the combination
switch reading function.
FR WIPER LOW
[Off/On]
Displays the status of the FR WIPER LOW switch in combination switch judged by BCM with the combination
switch reading function.
FR WASHER SW
[Off/On]
Displays the status of the FR WASHER switch in combination switch judged by BCM with the combination
switch reading function.
FR WIPER INT
[Off/On]
Displays the status of the FR WIPER INT switch in combination switch judged by BCM with the combination
switch reading function.
FR WIPER STOP
[Off/On]
Displays the status of the front wiper stop position signal received from IPDM E/R via CAN communication.
INT VOLUME
[1 - 7]
Displays the status of wiper intermittent dial position judged by BCM with the combination switch reading
function.
RR WIPER ON
[Off/On]
Displays the status of the RR WIPER ON switch in combination switch judged by BCM with the combination
switch reading function.
RR WIPER INT
[Off/On]
Displays the status of the RR WIPER INT switch in combination switch judged by BCM with the combination
switch reading function.
RR WASHER SW
[Off/On]
Displays the status of the RR WASHER switch in combination switch judged by BCM with the combination
switch reading function.
RR WIPER STOP
[Off/On]
Displays the status of the rear wiper stop position signal received from rear wiper motor.
TURN SIGNAL R
[Off/On]
Displays the status of the TURN RH switch in combination switch judged by BCM with the combination switch
reading function.
TURN SIGNAL L
[Off/On]
Displays the status of the TURN LH switch in combination switch judged by BCM with the combination switch
reading function.
TAIL LAMP SW
[Off/On]
Displays the status of the TAIL LAMP switch in combination switch judged by BCM with the combination
switch reading function.
BCS
DIAGNOSIS SYSTEM (BCM)
BCS-29
< FUNCTION DIAGNOSIS >
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
BCM
BCM : CONSULT-III Function (BCM - BCM)
INFOID:0000000003137924
WORK SUPPORT
IMMU
IMMU : CONSULT-III Function (BCM - IMMU)
INFOID:0000000003743939
APPLICATION ITEM
CONSULT-III performs the following functions via CAN communication with BCM.
DATA MONITOR
ACTIVE TEST
HI BEAM SW
[Off/On]
Displays the status of the HI BEAM switch in combination switch judged by BCM with the combination switch
reading function.
HEAD LAMP SW 1
[Off/On]
Displays the status of the HEADLAMP 1 switch in combination switch judged by BCM with the combination
switch reading function.
HEAD LAMP SW 2
[Off/On]
Displays the status of the HEADLAMP 2 switch in combination switch judged by BCM with the combination
switch reading function.
PASSING SW
[Off/On]
Displays the status of the PASSING switch in combination switch judged by BCM with the combination switch
reading function.
AUTO LIGHT SW
[Off/On]
Displays the status of the AUTO LIGHT switch in combination switch judged by BCM with the combination
switch reading function.
FR FOG SW
[Off/On]
Displays the status of the FR FOG switch in combination switch judged by BCM with the combination switch
reading function.
RR FOG SW
[Off/On]
NOTE:
The item is indicated, but not monitored.
Monitor item [UNIT]
Description
Item
Description
RESET SETTING VALUE
Return a value set with Work Support of each system to a default value in factory shipment.
Diagnosis mode
Function Description
DATA MONITOR
The BCM input/output signals are displayed.
ACTIVE TEST
The signals used to activate each device are forcibly supplied from BCM.
Monitor item
Content
CONFRM ID ALL
Indicates [YET] at all time.
Switch to [DONE] when a registered Intelligent Key is inserted into the key slot.
CONFIRM ID4
CONFIRM ID3
CONFIRM ID2
CONFIRM ID1
TP 4
Indicates the number of ID which has been registered.
TP 3
TP 2
TP 1
PUSH SW
Indicates [ON/OFF] condition of push-button ignition switch.
KEY SW -SLOT
Indicates [ON/OFF] condition of key slot.
BCS-30
< FUNCTION DIAGNOSIS >
DIAGNOSIS SYSTEM (BCM)
BATTERY SAVER
BATTERY SAVER : CONSULT-III Function (BCM - BATTERY SAVER)
INFOID:0000000003743944
WORK SUPPORT
*: Initial setting
DATA MONITOR
Test item
Description
THEFT IND
This test is able to check security indicator lamp operation.
The lamp will be turned on when “ON” on CONSULT-III screen touched.
Service item
Setting item
Setting
BATTERY SAVER SET
On*
With the exterior lamp battery saver function
Off
Without the exterior lamp battery saver function
ROOM LAMP BAT SAV SET
On*
With the interior room lamp battery saver function
Off
Without the interior room lamp battery saver function
ROOM LAMP TIMER SET
MODE 1*
30 min.
Sets the interior room lamp battery saver timer operating
time.
MODE 2
60 min.
Monitor item
[Unit]
Description
REQ SW-DR
[On/Off]
The switch status input from request switch (driver side)
REQ SW-AS
[On/Off]
The switch status input from request switch (passenger side)
REQ SW-RR
[On/Off]
NOTE:
The item is indicated, but not monitored.
REQ SW-RL
[On/Off]
PUSH SW
[On/Off]
The switch status input from push-button ignition switch
KEY SW-SLOT
[On/Off]
Key switch status input from key slot
UNLK SEN-DR
[On/Off]
Driver door unlock status input from unlock sensor
DOOR SW-DR
[On/Off]
The switch status input from front door switch (driver side)
DOOR SW-AS
[On/Off]
The switch status input from front door switch (passenger side)
DOOR SW-RR
[On/Off]
The switch status input from rear door switch RH
DOOR SW- RL
[On/Off]
The switch status input from rear door switch LH
DOOR SW-BK
[On/Off]
NOTE:
The item is indicated, but not monitored.
CDL LOCK SW
[On/Off]
Lock switch status received from central door lock switch by power window switch se-
rial link
CDL UNLOCK SW
[On/Off]
Unlock switch status received from central door lock switch by power window switch
serial link
KEY CYL LK-SW
[On/Off]
Lock switch status received from key cylinder switch by power window switch serial
link
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст