Infiniti EX35. Manual — part 31
ADP-118
< COMPONENT DIAGNOSIS >
TELESCOPIC MOTOR
TELESCOPIC MOTOR
Description
INFOID:0000000003134764
• The telescopic motor is installed to the steering column assembly.
• The telescopic motor is activated with the automatic drive positioner control unit.
• Compresses the steering column by changing the rotation direction of telescopic motor.
Component Function Check
INFOID:0000000003134765
1.
CHECK FUNCTION
1.
Turn ignition switch ON.
2.
Select “TELESCO MOTOR” in “Active test” mode with CONSULT-III.
3.
Check the telescopic motor operation.
Is the operation of relevant parts normal?
YES
>> INSPECTION END
NO
>> Perform diagnosis procedure. Refer to
ADP-118, "Diagnosis Procedure"
.
Diagnosis Procedure
INFOID:0000000003134766
1.
CHECK TELESCOPIC MOTOR POWER SUPPLY
1.
Turn ignition switch OFF.
2.
Disconnect tilt & telescopic motor connector.
3.
Turn the ignition switch ON.
4.
Perform “Active test” (“TELESCO MOTOR”) with CONSULT-III
5.
Check voltage between tilt & telescopic motor harness connector and ground.
Is the inspection result normal?
YES
>> Replace telescopic motor. (Built in steering column assembly.)
NO
>> GO TO 2.
2.
CHECK TELESCOPIC MOTOR CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect automatic drive positioner control unit and tilt & telescopic motor connector.
3.
Check continuity between automatic drive positioner control unit harness connector and tilt & telescopic
motor harness connector.
Test item
Description
TELESCO MOTOR
OFF
Steering telescopic
Stop
FR Forward
RR
Backward
(+)
(-)
Condition
Voltage (V)
(Approx.)
Tilt & telescopic motor
Connector
Terminal
M49
1
Ground
TELESCOPIC MO-
TOR
OFF
0
FR (forward)
0
RR (backward)
Battery voltage
2
OFF
0
FR (forward)
Battery voltage
RR (backward)
0
TELESCOPIC MOTOR
ADP-119
< COMPONENT DIAGNOSIS >
C
D
E
F
G
H
I
K
L
M
A
B
ADP
N
O
P
4.
Check continuity between automatic drive positioner control unit harness connector and ground.
Is the inspection result normal?
YES
>> Replace automatic drive positioner control unit. Refer to
ADP-210, "Removal and Installation"
.
NO
>> Repair or replace harness or connector.
Automatic drive positioner control unit
Tilt & telescopic motor
Continuity
Connector
Terminal
Connector
Terminal
M52
36
M49
2
Existed
44
1
Automatic drive positioner control unit
Ground
Continuity
Connector
Terminal
M52
36
Not existed
44
ADP-120
< COMPONENT DIAGNOSIS >
DOOR MIRROR MOTOR
DOOR MIRROR MOTOR
Description
INFOID:0000000003134767
It makes mirror face operate from side to side and up and down with the electric power that AUTOMATIC
DRIVE POSITIONER CONTROL UNIT supplies.
Component Function Check
INFOID:0000000003134768
1.
CHECK DOOR MIRROR MOTOR FUNCTION
Check the operation with “MIRROR MOTOR RH” and “MIRROR MOTOR LH” in “ACTIVE TEST” mode with
CONSULT-III
Refer to
ADP-42, "CONSULT-III Function"
.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Refer to
ADP-120, "Diagnosis Procedure"
Diagnosis Procedure
INFOID:0000000003134769
1.
CHECK DOOR MIRROR MOTOR INPUT SIGNAL
1.
Turn ignition switch ON.
2.
Check voltage between door mirror connector and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> GO TO 2.
2.
CHECK HARNESS CONTINUITY
1.
Turn ignition switch OFF.
2.
Disconnect automatic drive positioner control unit connector.
3.
Check continuity between automatic drive positioner control unit connector and door mirror connector.
[Door mirror driver side]
[Door mirror passenger side]
(+)
(–)
Condition
Voltage (V)
(Approx.)
Door mirror
Connector
Terminal
D3 (Driver side)
D33 (Passenger
side)
12
Ground
Door mirror remote
control switch
UP
Battery voltage
Other than above
0
11
LEFT
Battery voltage
Other than above
0
10
DOWN / RIGHT
Battery voltage
Other than above
0
Automatic drive positioner control unit
Door mirror (driver side)
Continuity
Connector
Terminal
Connector
Terminal
M51
16
D3
10
Existed
31
12
32
11
Automatic drive positioner control unit
Door mirror (passenger side)
Continuity
Connector
Terminal
Connector
Terminal
M51
14
D33
12
Existed
15
11
30
10
DOOR MIRROR MOTOR
ADP-121
< COMPONENT DIAGNOSIS >
C
D
E
F
G
H
I
K
L
M
A
B
ADP
N
O
P
4.
Check continuity between automatic drive positioner control unit connector and ground.
[Door mirror driver side]
[Door mirror passenger side]
Is the inspection result normal?
YES
>> Replace automatic drive positioner control unit. Refer to
ADP-210, "Removal and Installation"
.
NO
>> Repair or replace harness or connector.
3.
CHECK DOOR MIRROR MOTOR
Check door mirror motor.
Refer to
ADP-121, "Component Inspection"
.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Replace door mirror. Refer to
MIR-52, "DOOR MIRROR ASSEMBLY : Removal and Installation"
.
4.
CHECK INTERMITTENT INCIDENT
GI-38, "Intermittent Incident"
.
>> INSPECTION END
Component Inspection
INFOID:0000000003134770
1.
CHECK DOOR MIRROR MOTOR-I
Check that door mirror motor does not trap foreign objects and does not have any damage.
Refer to
MIR-52, "DOOR MIRROR ASSEMBLY : Exploded View"
.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Replace door mirror.Refer to
MIR-52, "DOOR MIRROR ASSEMBLY : Removal and Installation"
2.
CHECK DOOR MIRROR MOTOR-II
1.
Turn ignition switch OFF.
2.
Disconnect door mirror connector.
3.
Apply 12V to each power supply terminal of door mirror motor.
Is the inspection result normal?
YES
>> INSPECTION END
Automatic drive positioner control unit
Ground
Continuity
Connector
Terminal
M51
16
Not existed
31
32
Automatic drive positioner control unit
Ground
Continuity
Connector
Terminal
M51
14
Not existed
15
30
Door mirror
Operational direction
Connector
Terminal
(+)
(–)
D3 (Driver side)
D33 (Passenger side)
10
11
RIGHT
11
10
LEFT
12
10
UP
10
12
DOWN
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст