Infiniti EX35. Manual — part 328
EBD
BRC-27
< FUNCTION DIAGNOSIS >
[VDC/TCS/ABS]
C
D
E
G
H
I
J
K
L
M
A
B
BRC
N
O
P
Component Parts Location
INFOID:0000000003430107
For USA
JSFIA0234GB
1.
Steering angle sensor
2.
ABS warning lamp
3.
Brake warning lamp
4.
VDC OFF indicator lamp
5.
SLIP indicator lamp
6.
ABS actuator and electric unit (con-
trol unit)
BRC-28
< FUNCTION DIAGNOSIS >
[VDC/TCS/ABS]
EBD
Except for USA
7.
Front wheel sensor
8.
VDC OFF switch
9.
Yaw rate/side G sensor
10. Rear wheel sensor
A.
Back of spiral cable assembly
B.
Combination meter
C.
Inside brake master cylinder cover
D.
Steering knuckle
E.
Instrument driver lower panel
F.
Under center console
G.
Rear final drive assembly
JSFIA0235GB
EBD
BRC-29
< FUNCTION DIAGNOSIS >
[VDC/TCS/ABS]
C
D
E
G
H
I
J
K
L
M
A
B
BRC
N
O
P
Component Description
INFOID:0000000003430108
1.
Steering angle sensor
2.
ABS warning lamp
3.
Brake warning lamp
4.
VDC OFF indicator lamp
5.
SLIP indicator lamp
6.
ABS actuator and electric unit (con-
trol unit)
7.
Front wheel sensor
8.
VDC OFF switch
9.
Yaw rate/side G sensor
10. Rear wheel sensor
A.
Back of spiral cable assembly
B.
Combination meter
C.
Inside brake master cylinder cover
D.
Steering knuckle
E.
Instrument driver lower panel
F.
Under center console
G.
Rear final drive assembly
Component parts
Reference
ABS actuator and electric unit (control unit)
Pump
Motor
Actuator relay (main relay)
Solenoid valve
Pressure sensor
VDC switch-over valve
(USV1, USV2, HSV1, HSV2)
Wheel sensor
Yaw rate/side G sensor
Steering angle sensor
VDC OFF switch
ABS warning lamp
Brake warning lamp
VDC OFF indicator lamp
SLIP indicator lamp
BRC-30
< FUNCTION DIAGNOSIS >
[VDC/TCS/ABS]
DIAGNOSIS SYSTEM [ABS ACTUATOR AND ELECTRIC UNIT (CONTROL
UNIT)]
DIAGNOSIS SYSTEM [ABS ACTUATOR AND ELECTRIC UNIT (CONTROL
UNIT)]
CONSULT-III Function
INFOID:0000000003132875
FUNCTION
CONSULT-III can display each diagnostic item using the diagnostic test modes shown following.
WORK SUPPORT
CAUTION:
Erase DTC memory of the lane camera unit after implementing work support. Refer to
SULT-III Function (LANE CAMERA)"
.
SELF DIAGNOSTIC RESULT
Operation Procedure
Before performing the self-diagnosis, start engine and drive vehicle at 30 km/h (19 MPH) or more for approxi-
mately 1 minute.
Display Item List
How to Erase Self-diagnosis Results
After erasing DTC memory, start the engine and drive the vehicle at 30 km/h (19 MPH) or more for approxi-
mately 1 minute as the final inspection, and make sure that the ABS warning lamp, VDC OFF indicator lamp,
SLIP indicator lamp and brake warning lamp turn OFF.
CAUTION:
If memory cannot be erased, perform applicable diagnosis.
NOTE:
• When the wheel sensor malfunctions, after inspecting the wheel sensor system, ABS warning lamp, VDC
OFF indicator lamp, SLIP indicator lamp and brake warning lamp will not turn OFF even when the system is
normal unless the vehicle is driven at approximately 30 km/h (19 MPH) or more for approximately 1 minute.
• Brake warning lamp will turn ON in case of parking brake operation (when switch is ON) or in case of brake
fluid level switch operation (when brake fluid is insufficient).
• VDC OFF switch should not stay in “ON” position.
DATA MONITOR
Display Item List
Diagnostic test mode
Function
Work support
This mode enables a technician to adjust some devices faster and more accurately by following
the indications on CONSULT-III.
Self diagnostic result
Self-diagnostic results can be read and erased quickly.
Data monitor
Input/Output data in the ABS actuator and electric unit (control unit) can be read.
Active test
CONSULT-III drives some actuators apart from ABS actuator and electric unit (control unit) and
also shifts some parameters in a specified range.
ECU identification
ABS actuator and electric unit (control unit) part number can be read.
Item
Description
ST ANG SEN ADJUSTMENT
Adjusts the neutral position of the steering angle sensor.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст