Infiniti EX35. Manual — part 1448
TM-180
< ON-VEHICLE REPAIR >
[5AT: RE5R05A]
REVOLUTION SENSOR
REVOLUTION SENSOR
2WD
2WD : Exploded View
INFOID:0000000003130626
2WD : Removal and Installation
INFOID:0000000003130627
REMOVAL
1.
Disconnect the battery cable from the negative terminal.
2.
Drain ATF through drain plug.
3.
Remove exhaust front tube and center muffler with power tool. Refer to
.
4.
Remove rear propeller shaft. Refer to
5.
Remove control rod. Refer to
.
6.
Remove exhaust mounting bracket. Refer to
1.
Rear extension
2.
A/T
3.
Bracket
4.
Oil pan gasket
5.
Clip
6.
Oil pan mounting bolt
7.
Oil pan
8.
Drain plug
9.
Drain plug gasket
10.
Revolution sensor
11.
Self-sealing bolt
*
: Apply Genuine Anaerobic Liquid Gasket or equivalent. Refer to
GI-15, "Recommended Chemical Products and Sealants"
.
Refer to
for symbols not described on the above.
SCIA8271E
REVOLUTION SENSOR
TM-181
< ON-VEHICLE REPAIR >
[5AT: RE5R05A]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
7.
Disconnect heated oxygen sensor 2 harness connectors (A).
8.
Remove heated oxygen sensor 2 harness (B) from clips (1).
9.
Remove bracket (2) from transmission assembly.
10. Remove clips (1).
11. Remove oil pan (2) and oil pan gasket.
12. Support A/T assembly with a transmission jack.
CAUTION:
When setting transmission jack, place wooden blocks to
prevent from damaging control valve with TCM and trans-
mission case.
13. Remove rear engine mounting member with power tool. Refer to
14. Remove engine mounting insulator (rear). Refer to
15. Remove tightening bolts for rear extension assembly and trans-
mission case.
16. Tap rear extension assembly with a soft hammer (A).
: Vehicle front
: Bolt
SCIA8269E
3
: Drain plug
: Vehicle front
: Oil pan mounting bolt
1
: Self-sealing bolt
A
: Bolt
SCIA8117E
JPDIA0026ZZ
JPDIA0027ZZ
TM-182
< ON-VEHICLE REPAIR >
[5AT: RE5R05A]
REVOLUTION SENSOR
17. Remove rear extension assembly (with needle bearing) from
transmission case.
18. Disconnect revolution sensor connector (A).
CAUTION:
Be careful not to damage connector
19. Disengage terminal clip (
).
20. Remove revolution sensor (1) from transmission case.
CAUTION:
• Do not subject it to impact by dropping or hitting it.
• Do not disassemble.
• Do not allow metal filings, etc. to get on the sensor's front
edge magnetic area.
• Do not place in an area affected by magnetism.
INSTALLATION
Note the following, and install in the reverse order removal.
CAUTION:
• Insert the tip of parking rod between the parking pole and the parking actuator support when assem-
bling the rear extension assembly.
• Do not reuse drain plug gasket.
• Refer to the followings when revolution sensor.
CAUTION:
• Do not subject it to impact by dropping or hitting it.
• Do not disassemble.
• Do not allow metal filings, etc. to get on the sensor's front edge magnetic area.
• Do not place in an area affected by magnetism.
• Refer to the followings when installing rear extension assembly.
SCIA3431E
JPDIA0011ZZ
: Bolt
JPDIA0041ZZ
REVOLUTION SENSOR
TM-183
< ON-VEHICLE REPAIR >
[5AT: RE5R05A]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
- Apply recommended sealant (Genuine Anaerobic Liquid Gasket or
equivalent. Refer to
GI-15, "Recommended Chemical Products
.) to rear extension assembly as shown in the figure.
CAUTION:
Completely remove all moisture, oil and old sealant, etc. from
transmission case and rear extension assembly mounting
surfaces.
- Tighten rear extension assembly bolts to the specified torque.
• Refer to the followings when installing oil pan (2) (with oil pan gas-
ket) and clips (1) to transmission case.
CAUTION:
• Do not reuse oil pan gasket and oil pan mounting gasket.
• Install oil pan gasket in the direction to align hole position.
• Install it so that drain plug (3) comes to the position as
shown in the figure.
• Be careful not to pinch harnesses.
• Completely remove all moisture, oil and old gasket, etc. from oil pan mounting surface.
A
: Start and finish point shall be in the
center of two bolts.
B
: 3 – 5 mm (0.12 – 0.20 in)
Sealant
width (C)
: 1.0 – 2.0 mm (0.04 – 0.08 in)
Sealant
height (C)
: 0.4 – 1.0 mm (0.016 – 0.04 in)
JPDIA0036ZZ
1
: Self-searing bolt
A
: Bolt
JPDIA0026ZZ
: Vehicle front
: Oil pan mounting bolt
SCIA8117E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст