Infiniti EX35. Manual — part 4
ADP-10
< BASIC INSPECTION >
INSPECTION AND ADJUSTMENT
MEMORY STORING : Description
INFOID:0000000003134611
Always perform the memory storage when the battery terminal is disconnected or the driver seat control unit is
replaced. The memory function and Intelligent Key interlock function will not operate normally if no memory
storage is performed.
MEMORY STORING : Special Repair Requirement
INFOID:0000000003134612
Memory Storage Procedure
Two positions for the driver seat, steering column and outside mirror can be stored for memory operation by
following procedure.
1.
STEP 1
Shift A/T selector lever to P position.
>> GO TO 2.
2.
STEP 2
Turn ignition switch ON.
>> GO TO 3.
3.
STEP 3
Adjust driver seat, steering column and outside mirror position manually.
>> GO TO 4.
4.
STEP 4
1.
Push set switch.
NOTE:
• Memory indicator for which driver seat position is already retained in memory is illuminated for 5 sec-
onds.
• Memory indicator for which driver seat position is not retained in memory is illuminated for 0.5 second.
2.
Push the memory switch (1 or 2) for at least 1 second within 5 seconds after pushing the set switch.
NOTE:
• To enter driver seat positions into blank memory, memory indicator will be turned on for 5 seconds.
• To modify driver seat positions, memory indicator will be turned OFF for 0.5 second, then turned ON for
5 seconds.
NOTE:
If memory is stored in the same memory switch, the previous memory will be deleted.
Do you need linking of Intelligent Key?
YES
>> GO TO 6.
NO
>> GO TO 5.
5.
STEP 5
Confirm the operation of each part with memory operation.
>> END
6.
STEP 6
Push the Intelligent Key unlock button within 5 seconds after pushing memory switch (while the memory indi-
cator is turned ON).
>> GO TO 7.
7.
STEP 7
Confirm the operation of each part with memory operation and Intelligent Key interlock operation.
INSPECTION AND ADJUSTMENT
ADP-11
< BASIC INSPECTION >
C
D
E
F
G
H
I
K
L
M
A
B
ADP
N
O
P
>> END
SYSTEM SETTING
SYSTEM SETTING : Description
INFOID:0000000003134613
The settings of the automatic driving positioner system can be changed, using CONSULT-III, the display unit
in the center of the instrument panel and the set switch. Always check the settings before and after discon-
necting the battery terminal or replacing driver seat control unit.
Setting Change
×
: Applicable
*1
: If either of entry/exit assist (seat) or entry/exit assist (steering column) is turned OFF, seat synchronization function is also turned
OFF.
SYSTEM SETTING : Special Repair Requirement
INFOID:0000000003134614
1.
CHOOSE METHOD
There are three way of setting method.
Which method do you choose?
With display>>GO TO 2.
With set switch>>GO TO 4.
With CONSULT-III>>GO TO 6.
2.
WITH DISPLAY - STEP 1
Turn ignition switch ON.
>> GO TO 3.
3.
WITH DISPLAY - STEP 2
1.
Push “SETTING” button.
2.
Select “Comfort & convenience”.
3.
Select “Lift Steering Wheel ON Exit”or “Slide Driver
′
s Seat Back ON Exit” on display, then push
-
Lift Steering Wheel ON Exit: Entry/exit assist (steering column)
-
Slide Driver's Seat Back On Exit: Entry/exit assist (seat)
NOTE:
If either of entry/exit assist (seat) or entry/exit assist (steering column) is turned OFF, seat synchronization
function is also turned OFF.
>> END
4.
WITH SET SWITCH - STEP 1
Turn ignition switch OFF.
Item
Content
CON-
SULT
–III
Display
Set
switch
Factory
setting
Amount of seat sliding for
entry/exit assist
The amount of seat sliding for entry/exit assist can
be selected from 3 items.
[40mm/80mm/150mm]
x
—
—
40mm
Entry/exit assist
(seat)
Entry/exit assist (seat) can be selected:
ON (operated) – OFF (not operated)
x
x
x
OFF
Entry/exit assist
(steering column)
Entry/exit assist (steering column) can be selected:
ON (operated) – OFF (not operated)
x
x
OFF
Seat synchronization
Seat synchronization can be selected: ON (operat-
ed) – OFF (not operated)
NOTE:
*1
OFF
Reset custom settings
All settings can be set to default (factory setting).
—
x
—
—
ADP-12
< BASIC INSPECTION >
INSPECTION AND ADJUSTMENT
>> GO TO 5.
5.
WITH SET SWITCH - STEP 2
Push setting button and hold for more than 10 seconds, then confirm blinking of the memory switch indicator.
• Entry/exit assist (seat/steering column) and seat synchronization are ON: Memory switch indicator blink two
times.
• Entry/exit assist (seat/steering column) and seat synchronization are OFF: Memory switch indicator blink
once.
>> END
6.
WITH CONSULT-III - STEP 1
Select “Work support”.
>> GO TO 7.
7.
WITH CONSULT-III - STEP 2
1.
Select “EXIT SEAT SLIDE SETTING”, “EXIT TILT SETTING” or “SEAT SLIDE VOLUME SET” then touch
display to change between ON and OFF.
-
EXIT SEAT SLIDE SETTING: Entry/exit assist (seat)
-
EXIT TILT SETTING: Entry/exit assist (steering column)
2.
Then touch “OK”.
NOTE:
If either of entry/exit assist (seat) or entry/exit assist (steering column) is turned OFF, seat synchronization
function is also turned OFF.
>> END
AUTOMATIC DRIVE POSITIONER SYSTEM
ADP-13
< FUNCTION DIAGNOSIS >
C
D
E
F
G
H
I
K
L
M
A
B
ADP
N
O
P
FUNCTION DIAGNOSIS
AUTOMATIC DRIVE POSITIONER SYSTEM
AUTOMATIC DRIVE POSITIONER SYSTEM
AUTOMATIC DRIVE POSITIONER SYSTEM : System Diagram
INFOID:0000000003134615
JMJIA1716GB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст