Infiniti EX35. Manual — part 13
ADP-46
< COMPONENT DIAGNOSIS >
B2112 SLIDING MOTOR
B2112 SLIDING MOTOR
Description
INFOID:0000000003134649
• The seat sliding motor is installed to the seat cushion frame.
• The seat sliding motor is installed with the driver seat control unit.
• Slides the seat frontward/ rearward by changing the rotation direction of sliding motor.
DTC Logic
INFOID:0000000003134650
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
RERFORM DTC CONFIRMATION PROCEDURE
1.
Turn ignition switch ON.
2.
Check “Self diagnostic result” with CONSULT-III.
Is the DTC detected?
YES
>> Perform diagnosis procedure. Refer to
NO
>> INSPECTION END
NOTE:
First perform diagnosis for B2126 if B2126 is detected.
Diagnosis Procedure
INFOID:0000000003757155
1.
PERFORM DTC CONFIRMATION PROCEDURE
1.
Turn ignition switch ON.
2.
Check “Self diagnostic result” with CONSULT-III.
3.
Erase the DTC.
4.
Perform DTC confirmation procedure. Refer to
.
Is the DTC displayed again?
YES
>> GO TO 2.
NO
>> Check intermittent incident. Refer to
GI-38, "Intermittent Incident"
.
2.
CHECK SLIDING MOTOR CIRCUIT (POWER SHORT)
1.
Turn ignition switch OFF.
2.
Disconnect sliding motor and driver seat control unit connector.
3.
Check voltage between sliding motor harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace harness or connector.
3.
CHECK DRIVER SEAT CONTROL UNIT OUTPUT SIGNAL
1.
Connect driver seat control unit connector.
2.
Check voltage between driver seat control unit harness connector and ground.
DTC No.
Trouble diagnosis
name
DTC detecting condition
Possible cause
B2112
SEAT SLIDE
The driver seat control unit detects the output of slid-
ing motor output terminal for 0.1 second or more
even if the sliding switch is not input.
• Driver seat control unit
• Slide motor harness is power
shorted
(+)
(–)
Voltage (V)
(Approx.)
Sliding motor
Connector
Terminals
B461
35
Ground
0
42
B2112 SLIDING MOTOR
ADP-47
< COMPONENT DIAGNOSIS >
C
D
E
F
G
H
I
K
L
M
A
B
ADP
N
O
P
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Replace driver seat control unit. Refer to
ADP-209, "Removal and Installation"
4.
CHECK INTERMITTENT INCIDENT
GI-38, "Intermittent Incident"
.
>> INSPECTION END
(+)
(–)
Voltage (V)
(Approx.)
Driver seat control unit
Connector
Terminals
B451
35
Ground
0
42
ADP-48
< COMPONENT DIAGNOSIS >
B2113 RECLINING MOTOR
B2113 RECLINING MOTOR
Description
INFOID:0000000003134652
• The seat reclining motor is installed to the seatback frame.
• The seat reclining motor is activated with the driver seat control unit.
• Tilts the seatback frontward/rearward by changing the rotation direction of reclining motor.
DTC Logic
INFOID:0000000003134653
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
REFORM DTC CONFIRMATION PROCEDURE
1.
Turn ignition switch ON.
2.
Check “Self diagnostic result” with CONSULT-III.
Is the DTC detected?
YES
>> Perform diagnosis procedure. Refer to
NO
>> INSPECTION END
NOTE:
First perform diagnosis for B2126 if B2126 is detected.
Diagnosis Procedure
INFOID:0000000003757156
1.
PERFORM DTC CONFIRMATION PROCEDURE
1.
Turn ignition switch ON.
2.
Check “Self diagnostic result” with CONSULT-III.
3.
Erase the DTC.
4.
Perform DTC confirmation procedure. Refer to
.
Is the DTC displayed again?
YES
>> GO TO 2.
NO
>> Check intermittent incident. Refer to
GI-38, "Intermittent Incident"
.
2.
CHECK RECLINING MOTOR CIRCUIT (POWER SHORT)
1.
Turn ignition switch OFF.
2.
Disconnect reclining motor and driver seat control unit connector.
3.
Check voltage between reclining motor harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace harness or connector.
3.
CHECK DRIVER SEAT CONTROL UNIT OUTPUT SIGNAL
1.
Connect driver seat control unit connector.
2.
Check voltage between driver seat control unit harness connector and ground.
DTC No.
Trouble diagnosis
name
DTC detecting condition
Possible cause
B2113
SEAT RECLINING
The driver seat control unit detects the output of re-
clining motor output terminal for 0.1 second or more
even if the reclining switch is not input.
• Driver seat control unit
• Reclining motor harness is pow-
er shorted
(+)
(–)
Voltage (V)
(Approx.)
Reclining motor
Connector
Terminals
B454
36
Ground
0
44
B2113 RECLINING MOTOR
ADP-49
< COMPONENT DIAGNOSIS >
C
D
E
F
G
H
I
K
L
M
A
B
ADP
N
O
P
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Replace driver seat control unit. Refer to
ADP-209, "Removal and Installation"
4.
CHECK INTERMITTENT INCIDENT
GI-38, "Intermittent Incident"
.
>> INSPECTION END
(+)
(–)
Voltage (V)
(Approx.)
Driver seat control unit
Connector
Terminals
B451
36
Ground
0
44
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст