Infiniti EX35. Manual — part 1089
MWI-34
< FUNCTION DIAGNOSIS >
COMPASS
COMPASS
Description
INFOID:0000000003140177
DESCRIPTION
• This electronic compass is able to display 8 primary directions: N, NE, E, SE, S, SW, W, NW.
• The compass switch (1) is used to operate the compass.
Switch Operation
• All standard compasses determine direction relative to Magnetic North; however, this electronic compass is
designed to display direction relative to True North.
• The difference between Magnetic North and True North varies from place to place across the surface of the
earth.
• This electronic compass must be “told” approximately where it is on the earth’s surface so that the Magnetic
North reading can be properly converted into a True North display.
• To tell the electronic compass where it’s at, the earth is separated into numbered “Zone Variances”. The
Zone Variance number in which the compass is to function must be entered into this electronic compass.
• Each zone is magnetically about 4.2
°
wide. Typically, anything under 22.5
°
total zone change is not noticed
on the electronic compass display. However, over 22.5
°
, a reading may be off by one or more primary direc-
tions.
• On long trips, a vehicle may leave its original zone and enter one or more new zones. Generally, you do not
need to reset the compass zone if you travel between 3 or 4 zones, such as business travel or vacation. The
typical driver will not notice any difference on the display within 3 or 4 zones. However, if the vehicle is “per-
manently” moved to a new location, it is recommended that the compass zone be reset.
ZONE VARIATION SETTING PROCEDURE
SKIB8868E
Press
Compass is turned ON/OFF
Press and hold
(for 3- 9 sec.)
Compass display (2) turns to zone variation change
mode Compass
Press and hold (for more
than 9 sec.)
Compass display turns to calibration mode
MWI
COMPASS
MWI-35
< FUNCTION DIAGNOSIS >
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
1.
Press and hold the compass switch for 3 – 9 seconds.
2.
The current zone setting appears on the compass display.
3.
Find the current geographical location number in the Zone Varia-
tion Chart.
4.
Select the new zone number. (Press the compass switch until
the new zone number appears on the compass display.)
5.
After select the new zone number, the compass display will
automatically shows a direction within a few seconds.
6.
Perform the following Calibration Procedure for more accurate
indications.
CALIBRATION PROCEDURE
NOTE:
The compass calibrates itself under normal driving conditions. However, occasional circumstances may cause
the compass to operate inaccurately. Example: Driving from rural (wide open) areas to crowded city areas, or
if an aftermarket (i.e., non original equipment) antenna with a magnetic base is attached to the vehicle. Cali-
brate the mirror compass if the display shows only one direction or a limited number of directions.
NOTE:
• If “magnetic hats” are used in the dealership for vehicle identification, remove the hat from the vehicle before
performing the following steps. Do NOT put the hat back on the vehicle after the procedure is completed.
• Drive the vehicle to an open level area; away from large metallic objects, structures, and overhead power
lines.
• Turn off “non-essential” electrical accessories (rear window defrost, heater/air conditioning, wipers) and
close the doors.
1.
Verify the correct compass zone setting for the geographical location.
2.
Press and hold the compass switch for more than 9 seconds.
3.
“C“ is displayed on the compass display, when calibration starts.
4.
Drive slowly [less than 8 km/h (5 MPH)] in a circle until the “C / CAL” is replaced with primary headings (N,
NE, E, SE, S, SW, W, or NW).
NOTE:
This will require driving at least 2 complete 360 degree circles; 3 complete circles may be required.
5.
The compass calibration procedure is now complete. The compass should operate normally.
NOTE:
If at any time the compass continually displays the incorrect direction or the reading is erratic or locked,
repeat the calibration procedure.
SEL168Y
MWI-36
< FUNCTION DIAGNOSIS >
COMPASS
Component Parts Location
INFOID:0000000003140178
Special Repair Requirement
INFOID:0000000003140179
1.
PERFORM ZONE VARIATION SETTING
Perform the zone variation setting. Refer to
.
>> GO TO 2.
2.
PERFORM CALIBRATION
Perform the calibration. Refer to
.
>> Setting completion
1
: Compass switch
2
: Compass display
SKIB8868E
MWI
CLOCK
MWI-37
< FUNCTION DIAGNOSIS >
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
CLOCK
Component Parts Location
INFOID:0000000003140180
1
: Clock
JPNIA0763ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст