Infiniti EX35. Manual — part 827
EXL-352
< ON-VEHICLE REPAIR >
[HALOGEN TYPE]
FRONT COMBINATION LAMP
ON-VEHICLE REPAIR
FRONT COMBINATION LAMP
Exploded View
INFOID:0000000003534199
REMOVAL
DISASSEMBLY
Removal and Installation
INFOID:0000000003534200
REMOVAL
CAUTION:
1.
Front combination lamp
JPLIA0916ZZ
1.
Front side marker lamp bulb
2.
Front side marker lamp bulb socket
3.
Front turn signal lamp bulb socket
4.
Front turn signal lamp bulb
5.
Resin cap
6.
Seal packing
7.
Halogen bulb (LO)
8.
Halogen bulb (HI)
9.
Headlamp housing assembly
10.
Parking lamp bulb
11. Parking lamp bulb socket
JPLIA0932ZZ
FRONT COMBINATION LAMP
EXL-353
< ON-VEHICLE REPAIR >
[HALOGEN TYPE]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
Disconnect the battery negative terminal or remove the fuse.
1.
Remove the front bumper fascia. Refer to
.
2.
Remove the headlamp mounting bolts and clips.
3.
Remove the harness clip and the holding clip (A)
*
.
*: Left side only.
4.
Pull out the headlamp assembly forward the vehicle.
5.
Disconnect the connector before removing the headlamp
assembly.
INSTALLATION
Install in the reverse order of removal.
NOTE:
After installation, perform aiming adjustment. Refer to
.
Replacement
INFOID:0000000003534201
CAUTION:
• Disconnect the battery negative terminal or remove the fuse.
• After installing the bulb, install the resin cap and the bulb socket securely for watertightness.
• Never touch the glass of bulb directly by hand. Keep grease and other oily matters away from it.
Never touch bulb by hand while it is lit or right after being turned off.
• Never leave bulb out of lamp reflector for a long time because dust, moisture smoke, etc. may affect
the performance of lamp. When replacing bulb, be sure to replace it with new one.
HEADLAMP BULB (LO)
1.
Remove the fender rubber protector in the engine room. Keep a service area.
2.
Rotate the resin cap counterclockwise and unlock it.
3.
Disconnect the headlamp (LO) bulb connector.
4.
Rotate the bulb counterclockwise and unlock it.
5.
Remove the bulb from the headlamp housing assembly.
HEADLAMP BULB (HI)
1.
Remove the washer tank inlet
*
*:When replace a right.
2.
Disconnect the headlamp (HI) bulb connector.
3.
Rotate the bulb socket counterclockwise and unlock it.
4.
Remove the bulb socket from the headlamp housing assembly.
PARKING LAMP BULB
1.
Rotate the bulb socket counterclockwise and unlock it.
2.
Remove the bulb from the bulb socket.
FRONT TURN SIGNAL LAMP BULB
1.
Remove the fender rubber protector in the engine room. Keep a service area.
2.
Rotate the bulb socket counterclockwise and unlock it.
3.
Remove the bulb from the bulb socket.
FRONT SIDE MARKER LAMP BULB
1.
Remove the fender rubber protector in the engine room. Keep a service area.
2.
Rotate the bulb socket counterclockwise and unlock it.
3.
Remove the bulb from the bulb socket.
: Vehicle front
JPLIA0918ZZ
EXL-354
< ON-VEHICLE REPAIR >
[HALOGEN TYPE]
FRONT COMBINATION LAMP
Disassembly and Assembly
INFOID:0000000003534202
DISASSEMBLY
1.
Rotate the resin cap counterclockwise and unlock it.
2.
Disconnect the headlamp bulb (LO) connector.
3.
Rotate the headlamp bulb (LO) counterclockwise and unlock it
4.
Remove the bulb from the headlamp housing assembly.
5.
Rotate the headlamp bulb (HI) counterclockwise and unlock it
6.
Remove the bulb from the headlamp housing assembly.
7.
Rotate the parking lamp bulb socket counterclockwise and unlock it.
8.
Remove the bulb from the parking lamp bulb socket.
9.
Rotate the front turn signal lamp bulb socket counterclockwise and unlock it.
10. Remove the bulb from the front turn signal lamp bulb socket.
11. Rotate the front side marker lamp bulb socket counterclockwise and unlock it.
12. Remove the bulb from the front side marker lamp bulb socket.
ASSEMBLY
Assemble in the reverse order of disassembly.
FRONT FOG LAMP
EXL-355
< ON-VEHICLE REPAIR >
[HALOGEN TYPE]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
FRONT FOG LAMP
Exploded View
INFOID:0000000003757003
Removal and Installation
INFOID:0000000003757004
CAUTION:
Disconnect the battery negative terminal or remove the fuse.
REMOVAL
1.
Remove the front fender protector. Keep a service area. Refer to
.
2.
Remove the front fog lamp finisher.
3.
Remove the front fog lamp connector.
4.
Remove the screw.
5.
Disengage the pawl. And then remove the front fog lamp.
INSTALLATION
Installation is the reverse order of removal.
NOTE:
After installation, perform aiming adjustment. Refer to
Replacement
INFOID:0000000003757005
CAUTION:
• Disconnect the battery negative terminal or remove the fuse.
• Never touch the glass of bulb directly by hand. Keep grease and other oily matters away from it.
Never touch bulb by hand while it is lit or right after being turned off.
• Never leave bulb out of lamp reflector for a long time because dust, moisture smoke, etc. may affect
the performance of lamp. When replacing bulb, be sure to replace it with new one.
FRONT FOG LAMP BULB
1.
Remove the front fender protector. Keep the service area. Refer to
.
1.
Front fog lamp
2.
Front fog lamp finisher
: Pawl
JPLIA0920ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст