Infiniti EX35. Manual — part 1555
WW-72
< ECU DIAGNOSIS >
BCM (BODY CONTROL MODULE)
JCMWM1402GB
BCM (BODY CONTROL MODULE)
WW-73
< ECU DIAGNOSIS >
C
D
E
F
G
H
I
J
K
M
A
B
WW
N
O
P
JCMWM1403GB
WW-74
< ECU DIAGNOSIS >
BCM (BODY CONTROL MODULE)
Fail-safe
INFOID:0000000003769974
FAIL-SAFE CONTROL BY DTC
BCM performs fail-safe control when any DTC is detected.
JCMWM1404GB
BCM (BODY CONTROL MODULE)
WW-75
< ECU DIAGNOSIS >
C
D
E
F
G
H
I
J
K
M
A
B
WW
N
O
P
Display contents of CONSULT
Fail-safe
Cancellation
B2013: ID DISCORD BCM-S/L
Inhibit engine cranking
Erase DTC
B2014: CHAIN OF S/L-BCM
Inhibit engine cranking
Erase DTC
B2190: NATS ANTENNA AMP
Inhibit engine cranking
Erase DTC
B2191: DIFFERENCE OF KEY
Inhibit engine cranking
Erase DTC
B2192: ID DISCORD BCM-ECM
Inhibit engine cranking
Erase DTC
B2193: CHAIN OF BCM-ECM
Inhibit engine cranking
Erase DTC
B2557: VEHICLE SPEED
Inhibit steering lock
When normal vehicle speed signals have been received from ABS
actuator and electric unit (control unit) for 500 ms
B2560: STARTER CONT RELAY
Inhibit engine cranking
500 ms after the following CAN signal communication status has
become consistent
• Starter control relay signal
• Starter relay status signal
B2601: SHIFT POSITION
Inhibit steering lock
500 ms after the following signal reception status becomes consis-
tent
• Selector lever P position switch signal
• P range signal (CAN)
B2602: SHIFT POSITION
Inhibit steering lock
5 seconds after the following BCM recognition conditions are ful-
filled
• Ignition switch is in the ON position
• Selector lever P position switch signal: Except P position (battery
voltage)
• Vehicle speed: 4 km/h (2.5 MPH) or more
B2603: SHIFT POSI STATUS
Inhibit steering lock
500 ms after the following BCM recognition conditions are fulfilled
• Ignition switch is in the ON position
• Selector lever P position switch signal: Except P position (battery
voltage)
• Selector lever P/N position signal: Except P and N positions (0 V)
B2604: PNP SW
Inhibit steering lock
500 ms after any of the following BCM recognition conditions is ful-
filled
• Status 1
- Ignition switch is in the ON position
- Selector lever P/N position signal: P and N position (battery volt-
age)
- P range signal or N range signal (CAN): ON
• Status 2
- Ignition switch is in the ON position
- Selector lever P/N position signal: Except P and N positions (0 V)
- P range signal and N range signal (CAN): OFF
B2605: PNP SW
Inhibit steering lock
500 ms after any of the following BCM recognition conditions is ful-
filled
• Ignition switch is in the ON position
- Power position: IGN
- Selector lever P/N position signal: Except P and N positions (0 V)
- Interlock/PNP switch signal (CAN): OFF
• Status 2
- Ignition switch is in the ON position
- Selector lever P/N position signal: P or N position (battery volt-
age)
- PNP switch signal (CAN): ON
B2606: S/L RELAY
Inhibit engine cranking
500 ms after the following CAN signal communication status has
become consistent
• Steering lock relay signal (Request signal)
• Steering lock relay signal (Condition signal)
B2607: S/L RELAY
Inhibit engine cranking
500 ms after the following CAN signal communication status has
become consistent
• Steering lock relay signal (Request signal)
• Steering lock relay signal (Condition signal)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст