Infiniti EX35. Manual — part 1079
INSIDE MIRROR
MIR-71
< ON-VEHICLE REPAIR >
[WITHOUT ADP]
C
D
E
F
G
H
I
J
K
M
A
B
MIR
N
O
P
ON-VEHICLE REPAIR
INSIDE MIRROR
Exploded View
INFOID:0000000003777987
Base
Option
Removal and Installation
INFOID:0000000003777988
REMOVAL
Base model
1.
Inside mirror
2.
Mirror base
for symbols in the figure.
JMLIA0145ZZ
1.
Inside mirror
2.
Mirror base
3.
Inside mirror cover
4.
Harness connector
5.
TORX bolt
for symbols in the figure.
JMLIA0146GB
MIR-72
< ON-VEHICLE REPAIR >
[WITHOUT ADP]
INSIDE MIRROR
1.
Insert minus driver (A) under the inside mirror (1).
2.
Slide the inside mirror to the upper side while pushing the pqwl
downward.
CAUTION:
Never use excessive force to remove the inside mirror because
it is inserted tightly into the miror base.
Option model
1.
Remove the inside mirror cover.
2.
Remove TORX bolt.
3.
Disconnect harness connector.
4.
Slide the inside mirror upward to remove.
INSTALLATION
Install in the reverse order of removal.
CAUTION:
When inserting the inside mirror into the mirror base, be sure to push the pawl until it get connected to
the mirror base.
JMLIA0055ZZ
OUTSIDE MIRROR
MIR-73
< ON-VEHICLE REPAIR >
[WITHOUT ADP]
C
D
E
F
G
H
I
J
K
M
A
B
MIR
N
O
P
OUTSIDE MIRROR
DOOR MIRROR ASSEMBLY
DOOR MIRROR ASSEMBLY : Exploded View
INFOID:0000000003777989
DOOR MIRROR ASSEMBLY : Removal and Installation
INFOID:0000000003777990
REMOVAL
1.
Remove front door finisher. Refer to
INT-11, "DRIVER SIDE : Removal and Installation"
(driver side) or
INT-14, "PASSENGER SIDE : Removal and Installation"
(passenger side).
2.
Remove clips and remove corner cover.
3.
Disconnect door mirror harness connector.
4.
Remove door mirror mounting nuts, and remove door mirror assembly.
INSTALLATION
Install in the reverse order of removal.
CAUTION:
Perform camera image calibration. Refer to
AV-438, "CALIBRATING CAMERA IMAGE (AROUND VIEW
MONITOR) : Special Repair Requirement"
.
DOOR MIRROR ASSEMBLY : Disassembly and Assembly
INFOID:0000000003777991
DISASSEMBLY
1.
Door mirror cover
2.
Mirror assembly
3.
Glass mirror
4.
Side camera assembly (with side
camera model)
5.
Side camera finisher assembly (with
side camera model)
6.
Base cover
7.
Puddle lamp
8.
Corner cover
: Clip
: Pawl
JMKIA2089ZZ
MIR-74
< ON-VEHICLE REPAIR >
[WITHOUT ADP]
OUTSIDE MIRROR
1.
Remove door mirror cover. Refer to
MIR-76, "DOOR MIRROR COVER : Disassembly and Assembly"
2.
Remove side camera after removing door mirror assembly (BOSE audio with navigation model). Refer to
AV-928, "Removal and Installation"
AV-927, "Removal and Installation"
3.
Remove base cover and puddle lamp.
ASSEMBLY
Assemble in the reverse order of disassemble.
GLASS MIRROR
GLASS MIRROR : Exploded View
INFOID:0000000003777992
GLASS MIRROR : Disassembly and Assembly
INFOID:0000000003777993
DISASSEMBLY
1.
Place the glass mirror upward.
2.
Put a strip of protective tape (B) on housing assembly.
3.
As shown in the figure, insert a small slotted screwdriver (A) into the recess between glass mirror (1) and
actuator (2). Push up both pawls (3) simultaneously to remove glass mirror lower half side.
NOTE:
1.
Door mirror cover
2.
Mirror assembly
3.
Glass mirror
4.
Side camera assembly (with side
camera model)
5.
Side camera finisher assembly (with
side camera model)
6.
Base cover
7.
Puddle lamp
8.
Corner cover
: Clip
: Pawl
JMKIA2089ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст