Infiniti G35 (V35) Sedan. Manual — part 563
EC-398
< COMPONENT DIAGNOSIS >
[VQ35HR]
P1564 ICC STEERING SWITCH
P1564 ICC STEERING SWITCH
Description
INFOID:0000000000956798
ICC steering switch has variant values of electrical resistance for each button. ECM reads voltage variation of
switch, and determines which button is operated.
Refer to
for the ICC function.
DTC Logic
INFOID:0000000000956799
DTC DETECTION LOGIC
NOTE:
If DTC P1564 is displayed with DTC P0605, first perform the trouble diagnosis for DTC P0605. Refer to
DTC CONFIRMATION PROCEDURE
1.
PRECONDITIONING
If DTC Confirmation Procedure has been previously conducted, always turn ignition switch OFF and wait at
least 10 seconds before conducting the next test.
>> GO TO 2.
2.
PERFORM DTC CONFIRMATION PROCEDURE
1.
Turn ignition switch ON and wait at least 10 seconds.
2.
Press MAIN switch for at least 10 seconds, then release it and wait at least 10 seconds.
3.
Press CANCEL switch for at least 10 seconds, then release it and wait at least 10 seconds.
4.
Press RESUME/ACCELERATE switch for at least 10 seconds, then release it and wait at least 10 sec-
onds.
5.
Press SET/COAST switch for at least 10 seconds, then release it and wait at least 10 seconds.
6.
Press DISTANCE switch for at least 10 seconds, then release it and wait at least 10 seconds.
7.
Check DTC.
Is DTC detected?
YES
>> Go to
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000000956800
1.
CHECK GROUND CONNECTION
1.
Turn ignition switch OFF.
2.
Check ground connection M95. Refer to Ground Inspection in
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace ground connection.
2.
CHECK ICC STEERING SWITCH CIRCUIT
With CONSULT-III
1.
Turn ignition switch ON.
2.
Select “MAIN SW”, “CANCEL SW”, “RESUME/ACC SW”, “SET SW” and “DIST SW” in “DATA MONITOR”
mode with CONSULT-III.
DTC No.
Trouble diagnosis
name
DTC detecting condition
Possible cause
P1564
ICC steering switch
• An excessively high voltage signal from the
ICC steering switch is sent to ECM.
• ECM detects that input signal from the ICC
steering switch is out of the specified range.
• ECM detects that the ICC steering switch is
stuck ON.
• Harness or connectors
(The switch circuit is open or shorted.)
• ICC steering switch
• ECM
P1564 ICC STEERING SWITCH
EC-399
< COMPONENT DIAGNOSIS >
[VQ35HR]
C
D
E
F
G
H
I
J
K
L
M
A
EC
N
P
O
3.
Check each item indication under the following conditions.
Without CONSULT-III
1.
Turn ignition switch ON.
2.
Check the voltage between ECM harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 8.
NO
>> GO TO 3.
3.
CHECK ICC STEERING SWITCH GROUND CIRCUIT FOR OPEN AND SHORT
1.
Turn ignition switch OFF.
2.
Disconnect ECM harness connector.
3.
Disconnect combination switch harness connector M303.
4.
Check the continuity between combination switch and ECM harness connector.
5.
Also check harness for short to ground and short to power.
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> GO TO 4.
4.
DETECT MALFUNCTIONING PART
Check the following.
• Combination switch (spiral cable)
• Harness for open and short between ECM and combination switch
>> Repair open circuit or short to ground or short to power in harness or connectors.
5.
CHECK ICC STEERING SWITCH INPUT SIGNAL CIRCUIT FOR OPEN AND SHORT
Monitor item
Condition
Indication
MAIN SW
MAIN switch
Pressed
ON
Released
OFF
CANCEL SW
CANCEL switch
Pressed
ON
Released
OFF
RESUME/ACC SW
RESUME/ACCEL-
ERATE switch
Pressed
ON
Released
OFF
SET SW
SET/COAST switch
Pressed
ON
Released
OFF
DIST SW
DISTANCE switch
Pressed
ON
Released
OFF
ECM
Ground
Condition
Voltage
Connector
Terminal
M107
101
(ICC steering switch signal)
Ground
MAIN switch: Pressed
Approx. 0V
CANCEL switch: Pressed
Approx. 1.3V
DISTANCE switch: Pressed
Approx. 2.2V
SET/COAST switch: Pressed
Approx. 3.0V
RESUME/ACCELERATE switch: Pressed
Approx. 3.7V
All ICC steering switches: Released
Approx. 4.3V
Combination switch
ECM
Continuity
Terminal
Connector
Terminal
16
M107
108
Existed
EC-400
< COMPONENT DIAGNOSIS >
[VQ35HR]
P1564 ICC STEERING SWITCH
1.
Check the continuity between combination switch and ECM harness connector.
2.
Also check harness for short to ground and short to power.
Is the inspection result normal?
YES
>> GO TO 7.
NO
>> GO TO 6.
6.
DETECT MALFUNCTIONING PART
Check the following.
• Combination switch (spiral cable)
• Harness for open and short between ECM and combination switch
>> Repair open circuit or short to ground or short to power in harness or connectors.
7.
CHECK ICC STEERING SWITCH
EC-400, "Component Inspection"
Is the inspection result normal?
YES
>> GO TO 8.
NO
>> Replace ICC steering switch.
8.
CHECK INTERMITTENT INCIDENT
GI-39, "Intermittent Incident"
>> INSPECTION END
Component Inspection
INFOID:0000000000956801
1.
CHECK ICC STEERING SWITCH
1.
Turn ignition switch OFF.
2.
Disconnect combination switch (spiral cable) harness connector M303.
3.
Check resistance between combination switch harness connector terminals under the following condi-
tions.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Replace ICC steering switch
Combination switch
ECM
Continuity
Terminal
Connector
Terminal
13
M107
101
Existed
Combination switch
Condition
Resistance
Connector
Terminals
M303
13 and 16
MAIN switch: Pressed
Approx. 0
Ω
CANCEL switch: Pressed
Approx. 310
Ω
DISTANCE switch: Pressed
Approx. 740
Ω
SET/COAST switch: Pressed
Approx. 1,400
Ω
RESUME/ACCELERATE switch: Pressed
Approx. 2,600
Ω
All ICC steering switches: Released
Approx. 5,500
Ω
P1568 ICC FUNCTION
EC-401
< COMPONENT DIAGNOSIS >
[VQ35HR]
C
D
E
F
G
H
I
J
K
L
M
A
EC
N
P
O
P1568 ICC FUNCTION
DTC Logic
INFOID:0000000000956802
DTC DETECTION LOGIC
NOTE:
• If DTC P1568 is displayed with DTC U1000 or U1001, first perform the trouble diagnosis for DTC
U1000, U1001. Refer to
• If DTC P1568 is displayed with DTC U1010, first perform the trouble diagnosis for DTC U1010. Refer
.
• If DTC P1568 is displayed with DTC P0605, first perform the trouble diagnosis for DTC P0605. Refer
.
DTC CONFIRMATION PROCEDURE
1.
PRECONDITIONING
If DTC Confirmation Procedure has been previously conducted, always turn ignition switch OFF and wait at
least 10 seconds before conducting the next test.
TESTING CONDITION:
Step 4 may be conducted with the drive wheels lifted in the shop or by driving the vehicle. If a road test
is expected to be easier, it is unnecessary to lift the vehicle.
>> GO TO 2.
2.
PERFORM DTC CONFIRMATION PROCEDURE
1.
Turn ignition switch ON.
2.
Press MAIN switch on ICC steering switch.
3.
Drive the vehicle at more than 40 km/h (25 MPH).
CAUTION:
Always drive vehicle at a safe speed.
4.
Press SET/COAST switch.
5.
Check DTC.
Is DTC detected?
YES
>> Go to
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000000956803
1.
REPLACE ICC SENSOR INTEGRATED UNIT
1.
Replace ICC sensor integrated unit.
2.
Perform
CCS-11, "ACTION TEST : Special Repair Requirement (Vehicle-To-Vehicle Distance Control
.
3.
Check DTC of ICC sensor integrated unit. Refer to
CCS-23, "Diagnosis Description"
>> INSPECTION END
DTC No.
Trouble Diagnosis
Name
DTC Detecting Condition
Possible Cause
P1568
ICC function
ECM detects a difference between signals
from ICC sensor integrated unit is out of spec-
ified range.
• Harness or connectors
(The CAN communication line is open or
shorted.)
• ICC sensor integrated unit
• ECM
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст