Infiniti G35 (V35) Sedan. Manual — part 753
HA-46
< ON-VEHICLE REPAIR >
LOW-PRESSURE FLEXIBLE HOSE AND PIPE 2
5.
Remove mounting bolt (A) from low-pressure flexible hose
bracket (1).
6.
Disconnect the one-touch joint between low-pressure pipe 1 (1)
and low-pressure pipe 2 (2) with disconnector (A) (SST:
9253089916).
CAUTION:
Cap or wrap the joint of low-pressure pipe 1 and 2 with suit-
able material such as vinyl tape to avoid the entry of air.
7.
Disconnect the one-touch joint between low-pressure pipe 2 (1)
and low-pressure flexible hose (2) with disconnector (A) (SST:
9253089916).
CAUTION:
Cap or wrap the joint of low-pressure pipe 2 and low-pres-
sure flexible hose with suitable material such as vinyl tape
to avoid the entry of air.
8.
Remove the low-pressure pipe 2 clip (B).
9.
Remove low-pressure pipe 2.
10. Remove mounting nut (A) from low-pressure flexible hose (1).
CAUTION:
Cap or wrap the joint of low-pressure flexible hose with
suitable material such as vinyl tape to avoid the entry of air.
11. Remove low-pressure flexible hose.
INSTALLATION
Installation is basically the reverse order of removal.
CAUTION:
• Replace O-rings of low-pressure flexible hose and low-pressure pipe 2 with new ones, and then
apply compressor oil to it when installing it.
• Female-side piping connection is thin and easy to deform. Slowly insert the male-side piping
straight in axial direction.
• Insert piping securely until a click is heard.
• After piping connection is completed, pull male-side piping by hand to make sure that connection
does not come loose.
• When recharging refrigerant, check for leaks.
JSIIA0023ZZ
JSIIA0091ZZ
JSIIA0024ZZ
JSIIA0025ZZ
HIGH-PRESSURE FLEXIBLE HOSE
HA-47
< ON-VEHICLE REPAIR >
C
D
E
F
G
H
J
K
L
M
A
B
HA
N
O
P
HIGH-PRESSURE FLEXIBLE HOSE
Exploded View
INFOID:0000000000959874
HA-17, "Refrigerant Connection"
.
Removal and Installation
INFOID:0000000000959875
REMOVAL
1.
Use a refrigerant collecting equipment (for HFC-134a) to discharge the refrigerant.
2.
Remove engine cover. Refer to
EM-27, "Removal and Installation"
3.
Remove air cleaner case (LH) and air duct (LH). Refer to
EM-25, "Removal and Installation"
1.
Blower unit
2.
O-ring
3.
Low-pressure pipe 2
4.
Low-pressure flexible hose
5.
Compressor
6.
Radiator & condenser assembly
7.
High-pressure flexible hose
8.
High-pressure pipe 1
9.
Heater & cooling unit assembly
10. Expansion valve
11.
Evaporator
12. High-pressure pipe 2
13. Low-pressure pipe 1
JSIIA0109GB
HA-48
< ON-VEHICLE REPAIR >
HIGH-PRESSURE FLEXIBLE HOSE
4.
Remove mounting bolt (A) from high-pressure flexible hose
bracket (1).
5.
Disconnect the one-touch joint between high-pressure flexible
hose (1) and condenser pipe assembly (2) with disconnector (A)
(SST: 9253089912).
CAUTION:
Cap or wrap the joint of high-pressure flexible hose and
condenser pipe assembly with suitable material such as
vinyl tape to avoid the entry of air.
6.
Remove mounting nut (A) from high-pressure flexible hose (1),
and then remove high-pressure flexible hose.
CAUTION:
Cap or wrap the joint of compressor and high-pressure flex-
ible hose with suitable material such as vinyl tape to avoid
the entry of air.
INSTALLATION
Installation is basically the reverse order of removal.
CAUTION:
• Replace O-rings of high-pressure flexible hose with new ones, and then apply compressor oil to it
when installing it.
• Female-side piping connection is thin and easy to deform. Slowly insert the male-side piping
straight in axial direction.
• Insert piping securely until a click is heard.
• After piping connection is completed, pull male-side piping by hand to make sure that connection
does not come loose.
• When recharging refrigerant, check for leaks.
JSIIA0026ZZ
JSIIA0027ZZ
JSIIA0086ZZ
HIGH-PRESSURE PIPE 1(ENGINE COMPARTMENT)
HA-49
< ON-VEHICLE REPAIR >
C
D
E
F
G
H
J
K
L
M
A
B
HA
N
O
P
HIGH-PRESSURE PIPE 1(ENGINE COMPARTMENT)
Exploded View
INFOID:0000000000959876
HA-17, "Refrigerant Connection"
.
Removal and Installation
INFOID:0000000000959877
REMOVAL
1.
Remove low-pressure flexible hose and pipe 2. Refer to
HA-45, "Removal and Installation"
2.
Remove mounting bolt (A) from high-pressure flexible hose
bracket (1).
1.
Blower unit
2.
O-ring
3.
Low-pressure pipe 2
4.
Low-pressure flexible hose
5.
Compressor
6.
Radiator & condenser assembly
7.
High-pressure flexible hose
8.
High-pressure pipe 1
9.
Heater & cooling unit assembly
10. Expansion valve
11.
Evaporator
12. High-pressure pipe 2
13. Low-pressure pipe 1
JSIIA0109GB
JSIIA0026ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст