Infiniti G35 (V35) Sedan. Manual — part 1476
WT-92
< ON-VEHICLE REPAIR >
ROAD WHEEL TIRE ASSEMBLY
• Perform the ID registration, after tire rotation. Refer to
WT-5, "ID REGISTRATION PROCEDURE : Special
TIRE ROTATION (for 18 inch wheel models)
• Tire cannot be rotated in vehicle, as front tire are different size from rear tire and the direction of wheel rota-
tion is fixed in each tire.
CAUTION:
Do not include the T-type spare tire when rotating the tires.
Safety Device Preventing from Being Incorrectly installed
FRONT BRAKE DISC ROTOR AND FRONT WHEEL
• Front and rear wheel size for this model differs, therefore special pin (1) has been installed on the front brake
disc rotor (2). To accommodate this pin a hole (3) has been provided on the front wheel (4) (the rear wheel
does not have this hole.) and in some case the rear wheel is being mistakenly installed on the front.
T-TYPE SPARE TIRE WHEEL
• Regarding spare tire (for emergency) wheel, wrong assembly pro-
tection pin through hole (1) has been set in addition to regular bolt
holes (2) in order to enable installation to front wheel.
Wheel nuts tighting torque
: Refer to
.
JPEIC0015ZZ
JPEIC0016ZZ
TRANSMITTER
WT-93
< REMOVAL AND INSTALLATION >
C
D
F
G
H
I
J
K
L
M
A
B
WT
N
O
P
REMOVAL AND INSTALLATION
TRANSMITTER
Exploded View
INFOID:0000000000957931
Removal and Installation
INFOID:0000000000957932
REMOVAL
1.
Deflate tire. Unscrew transmitter retaining nut and allow transmitter to fall into tire.
2.
Gently bounce tire so that transmitter falls to bottom of tire.
Place on tire changing machine and break both tire beads
ensuring that the transmitter remains at the bottom of the tire.
3.
Turn tire so that valve hole is at bottom and bounce so that
transmitter (1) is near valve hole. Carefully lift tire onto turntable
and position valve hole (and transmitter) 270 degree from
mounting/dismounting head (2).
4.
Lubricate tire well and remove first side of the tire. Reach inside
the tire and remove the transmitter.
INSTALLATION
JPEIC0006GB
1.
Transmitter
2.
Grommet seal
3.
Valve nut
4.
Valve core
5.
Cap
Refer to
for symbols in figure.
SEIA0047E
JPEIC0014GB
WT-94
< REMOVAL AND INSTALLATION >
TRANSMITTER
1.
Put first side of tire onto rim.
2.
Mount transmitter on rim and tighten nut.
CAUTION:
Speed for tightening nut should be less than 15 rpm.
3.
Place wheel on turntable of tire machine. Ensure that transmitter
(1) is 270 degree from mounting head (2) when second side of
tire is fitted.
NOTE:
Do not touch transmitter at mounting head.
4.
Lubricate tire well and fit second side of tire as normal. Ensure
that tire does not rotate relative to rim.
5.
Inflate tire and fit to appropriate wheel position.
SEIA0049E
JPEIC0014GB
SERVICE DATA AND SPECIFICATIONS (SDS)
WT-95
< SERVICE DATA AND SPECIFICATIONS (SDS)
C
D
F
G
H
I
J
K
L
M
A
B
WT
N
O
P
SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
Road Wheel
INFOID:0000000000957933
Tire
INFOID:0000000000957934
Unit: kPa (kg/cm
2
, psi)
Kind of wheel
Aluminum
Maximum radial runout limit
Lateral deflection
Less than 0.3 mm (0.012 in)
Vertical deflection
Maximum allowable unbalance limit
Dynamic (At flange)
Less than 5 g (0.17 oz) (one side)
Static (At flange)
Less than 10 g (0.35 oz)
Wheel nuts tighting torque
108 N·m (11 kg-m, 80 ft-lb)
Tire size
Air pressure
Front
Rear
P225/55R17 95V
230 (2.3, 33)
230 (2.3, 33)
225/50R18 95W
230 (2.3, 33)
–
245/45R18 96W
–
230 (2.3, 33)
T145/80D17 107M
420 (4.2, 60)
420 (4.2, 60)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст