Infiniti G35 (V35) Sedan. Manual — part 417
DLN-102
< ON-VEHICLE REPAIR >
[REAR PROPELLER SHAFT: 3F80A-1VL107]
REAR PROPELLER SHAFT
5.
Put matching marks on propeller shaft flange yoke with transfer
companion flange.
CAUTION:
For matching marks, use paint. Never damage propeller
shaft flange yoke and transfer companion flange.
6.
Put matching marks on propeller shaft rebro joint with final drive
companion flange.
CAUTION:
For matching marks, use paint. Never damage propeller
shaft rebro joint and final drive companion flange.
7.
Loosen mounting nuts of center bearing mounting brackets.
CAUTION:
Tighten mounting nuts temporarily.
8.
Remove propeller shaft assembly fixing bolts and nuts.
9.
Remove center bearing mounting bracket fixing nuts.
10. Remove propeller shaft assembly.
CAUTION:
If constant velocity joint was bent during propeller shaft
assembly removal, installation, or transportation, its boot
may be damaged. Wrap boot interference area to metal part
with shop cloth or rubber to protect boot from breakage.
INSTALLATION
Note the following, and install in the reverse order of removal.
SDIA1822E
PDIA0470E
PDIA0402E
REAR PROPELLER SHAFT
DLN-103
< ON-VEHICLE REPAIR >
[REAR PROPELLER SHAFT: 3F80A-1VL107]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
• Install center bearing mounting bracket (Upper) (1) with its arrow
mark (A) facing forward.
• Adjust position of center bearing mounting bracket (1, 2) sliding
back and forth to prevent play in thrust direction of center bearing
insulator (3). Install bracket to vehicle.
• Align matching marks to install propeller shaft flange yoke with
transfer companion flange.
• Align matching marks to install propeller shaft rebro joint with final
drive companion flange.
• After assembly, perform a driving test to check propeller shaft
vibration. If vibration occurred, separate propeller shaft from final
drive. Reinstall companion flange after rotating it by 60, 120, 180,
240, 300 degrees. Then perform driving test and check propeller
shaft vibration again at each point.
JSDIA0127ZZ
SDIA1822E
PDIA0470E
DLN-104
< ON-VEHICLE REPAIR >
[REAR PROPELLER SHAFT: 3F80A-1VL107]
REAR PROPELLER SHAFT
• If propeller shaft or final drive has been replaced, connect them as
follows:
- Install the propeller shaft while aligning its matching mark A with
the matching mark B on the joint as close as possible.
CAUTION:
Avoid damaging the rebro joint boot, protect it with a shop
towel or equivalent.
Inspection
INFOID:0000000000957336
APPEARANCE
Check propeller shaft for bend and damage. If damage is detected, replace propeller shaft assembly.
PROPELLER SHAFT RUNOUT
Check propeller shaft runout at measuring points. If runout exceeds
specifications, replace propeller shaft assembly. For measuring
point, refer to
.
JOURNAL AXIAL PLAY
As shown in the figure, while fixing yoke on one side, check axial
play of joint. If outside the standard, replace propeller shaft assem-
bly.
CAUTION:
Never disassemble joints.
CENTER BEARING
Check center bearing for noise and damage. If noise or damage is detected, replace propeller shaft assembly.
CAUTION:
Never disassemble center bearing.
SDIA2049E
Limit
Propeller shaft runout
: Refer to
.
JSDIA0079ZZ
Standard
Journal axial play
: Refer to
PDA0005D
SERVICE DATA AND SPECIFICATIONS (SDS)
DLN-105
< SERVICE DATA AND SPECIFICATIONS (SDS)
[REAR PROPELLER SHAFT: 3F80A-1VL107]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
General Specifications
INFOID:0000000000957337
Propeller Shaft Runout
INFOID:0000000000957338
Unit: mm (in)
Journal Axial Play
INFOID:0000000000957339
Unit: mm (in)
Applied model
AWD
VQ35HR
A/T
Propeller shaft model
3F80A-1VL107
Number of joints
3
Type of journal bearings
(Non-disassembly type)
1st joint
Shell type
2nd joint
Shell type
3rd joint
Rebro joint type
Coupling method with transfer
Flange type
Coupling method with rear final drive
Rebro joint type
Shaft length
1st (Spider to spider)
399 mm (15.71 in)
2nd (Spider to rebro joint center)
753 mm (29.65 in)
Shaft outer diameter
1st
82.6 mm (3.25 in)
2nd
75.0 mm (2.95 in)
Item
Limit
Propeller shaft runout
0.8 (0.031)
Item
Standard
Journal axial play
0 (0)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст