Infiniti G35 (V35) Sedan. Manual — part 1124
RF-66
< ON-VEHICLE REPAIR >
SUNROOF UNIT ASSEMBLY
ON-VEHICLE REPAIR
SUNROOF UNIT ASSEMBLY
Exploded View
INFOID:0000000000961781
REMOVAL
1.
Drain hose
2.
Side trim (LH/RH)
3.
TORX bolt (T25)
4.
Glass lid
5.
Sunroof motor assembly
6.
Sunroof bracket (LH/RH)
7.
Sunroof unit assembly
8.
Drain connector
JMKIA0027ZZ
SUNROOF UNIT ASSEMBLY
RF-67
< ON-VEHICLE REPAIR >
C
D
E
F
G
H
I
J
L
M
A
B
RF
N
O
P
DISASSEMBLY
Removal and Installation
INFOID:0000000000961782
REMOVAL
CAUTION:
• Always work with a helper.
• Fully close the glass lid assembly, before removal, then do not operate sunroof motor assembly after
removal.
1.
Sunshade stopper
2.
Rear drain assembly
3.
Sunshade
4.
Sunroof frame
JMKIA0028ZZ
RF-68
< ON-VEHICLE REPAIR >
SUNROOF UNIT ASSEMBLY
• When taking sunroof unit out, use cloths to protect the seats and trim from damage.
• After installing the sunroof unit and glass lid, perform the leak test and check that there is no mal-
function.
1.
Remove the headlining. Refer to
.
2.
Disconnect drain hoses.
3.
Tilt up glass lid, and then remove side trim.
4.
Remove the TORX bolt (A) and remove glass lid.
5.
Remove sunroof motor assembly mounting screws. Disconnect connector from sunroof motor assembly
and then remove sunroof motor assembly.
CAUTION:
• Before removing sunroof motor, check that sunroof lid is fully closed.
• After removing sunroof motor, do not attempt to rotate sunroof motor assembly as a single unit.
6.
Remove grip bracket.
7.
Remove sunroof bracket bolts.
8.
Remove nuts from the front end and side rail, and then remove sunroof unit assembly from roof panel.
9.
Remove sunroof unit assembly through the passenger compartment while being careful not to damage
the seats and trim.
INSTALLATION
1.
Temporarily tighten the mounting bolts to the sunroof brackets (RH/LH).
2.
Bring sunroof unit into passenger compartment, and then place the rear end of the rail onto the sunroof
brackets.
3.
Temporarily tighten the mounting nuts to the front end of sunroof unit assembly.
4.
Tighten the installation points diagonally excluding the installation point of the sunroof bracket around the
roof opening.
5.
Tighten the sunroof bracket bolts of the vehicle side, and then tighten the bolt of the rail side.
6.
Tighten the mounting nuts to the front end and side rail.
7.
Move the sunroof motor assembly laterally by little so that the gear is completely engaged into the wire on
the sunroof unit assembly and mounting surface becomes parallel. Then secure the sunroof motor
assembly with screws.
CAUTION:
Before installing the sunroof motor assembly, be sure to the place the link and wire assembly in
the symmetrical and fully closed position.
8.
Install glass lid.
NOTE:
After installation, carry out fitting adjustment.
9.
Install side trim.
10. Connect drain hoses.
11. Install headlining. Refer to
.
Disassembly and Assembly
INFOID:0000000000961783
DISASSEMBLY
1.
Remove sunshade stopper mounting from the rear end of sunroof frame.
JMKIA0029ZZ
SUNROOF UNIT ASSEMBLY
RF-69
< ON-VEHICLE REPAIR >
C
D
E
F
G
H
I
J
L
M
A
B
RF
N
O
P
2.
Remove rear drain assembly from sunroof guide assembly.
3.
Remove sunshade from the rear end of sunroof frame.
ASSEMBLY
Assemble in the reverse order of disassembly.
Adjustment
INFOID:0000000000961784
LID WEATHERSTRIP OVERLAP ADJUSTMENT AND SURFACE MISMATCH ADJUSTMENT
1.
Tilt up glass lid, and then remove side trim.
2.
After loosening glass lid from TORX bolts (left and right), tilt down glass lid.
3.
Adjust glass lid from outside of vehicle so it resembles “A–A” “B–B” "C–C" as shown in the figure.
4.
To prevent glass lid from moving after adjustment, first tighten the bolts of front left, and then tighten the
bolts of rear right.
5.
Tighten remaining bolts, being careful to prevent glass lid from moving.
6.
Tilt glass lid up and down several times to check that it moves smoothly.
NOTE:
After adjustment the sunroof unit assembly, perform additional service. Refer to
VICE WHEN REPLACING CONTROL UNIT : Special Repair Requirement"
.
On Vehicle Service Procedure
INFOID:0000000000961785
SUNROOF MOTOR ASSEMBLY
Removal
1.
Remove the headlining. Refer to
.
PIIB3117J
a
b
A–A
0.6 - 2.2 mm (0.024 - 0.087 in)
-2.3 - 0.7 mm (-0.091 - 0.028 in)
B–B
0.6 - 2.2 mm (0.024 - 0.087 in)
-2.3 - 0.7 mm (-0.091 - 0.028 in)
C–C
0.6 - 2.2 mm (0.024 - 0.087 in)
-2.3 - 0.7 mm (-0.091 - 0.028 in)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст