Infiniti G35 (V35) Sedan. Manual — part 307
CHG
ALTERNATOR
CHG-27
< ON-VEHICLE REPAIR >
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
DISASSEMBLY
Type: A3TJ1991
AWD : Removal and Installation
INFOID:0000000000964292
REMOVAL
1.
Disconnect the battery cable from the negative terminal.
2.
Remove air cleaner case (RH). Refer to
3.
Remove the clip (B) from the harness bracket (1) and “B” termi-
nal harness from the clip (C).
4.
Disconnect pressure sensor connector (A).
5.
Remove engine undercover, using power tools.
: Engine front
Refer to
1.
Rear bearing
2.
Rotor assembly
3.
Retainer
4.
Front bearing
5.
Front bracket assembly
6.
Pulley
7.
Pulley nut
8.
Stator assembly
9.
IC voltage regulator assembly
10. Diode assembly
11.
Rear bracket assembly
12. Terminal set
13. “B” terminal nut
Refer to
JSMIA0007GB
JSMIA0013ZZ
CHG-28
< ON-VEHICLE REPAIR >
ALTERNATOR
6.
Remove radiator cooling fan assembly. Refer to
.
7.
Remove drive belt. Refer to
EM-12, "Removal and Installation"
.
8.
Remove alternator mounting bolt (B) and alternator stay mount-
ing bolt (C) using power tools, then remove alternator stay (1).
9.
Remove alternator mounting bolt (A), using power tools.
10. Pull and turn alternator, and then remove the harness bracket
bolts (A).
11. Disconnect alternator connector (1).
12. Remove “B” terminal nut (2).
13. Remove alternator assembly downward from the vehicle.
INSTALLATION
Install in the reverse order of removal.
CAUTION:
Be sure to tighten “B” terminal nut carefully.
• Install alternator, and check tension of belt. Refer to
• For this model, the power generation voltage variable control system that controls the power generation volt-
age of the alternator has been adopted. Therefore, the power generation voltage variable control system
operation inspection should be performed after replacing the alternator, and then make sure that the system
operates normally. Refer to
CHG-22, "Inspection Procedure"
.
AWD : Inspection
INFOID:0000000000964293
ALTERNATOR PULLEY INSPECTION
Perform the following.
• Make sure that alternator pulley does not rattle.
• Make sure that alternator pulley nut is tight. Refer to
JSMIA0014ZZ
SKIB2608J
CHG
SERVICE DATA AND SPECIFICATIONS (SDS)
CHG-29
< SERVICE DATA AND SPECIFICATIONS (SDS)
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
Alternator
INFOID:0000000000964294
*: Adjustment range of power generation voltage variable control is 11.4 - 15.6 V.
Type
A3TJ1991
MITSUBISHI make
Nominal rating
[V - A]
12 -150
Ground polarity
Negative
Minimum revolution under no-load (When 13.5 V is ap-
plied)
[rpm]
Less than 1,300
Hot output current (When 13.5 V is applied)
[A/rpm]
More than 31/1,300
More than 122/2,500
More than 144/5,000
Regulated output voltage
[V]
14.1 - 14.7
*
Minimum length of brush
[mm (in)]
More than 5.00 (0.197)
Brush spring pressure
[N (g, oz)]
4.1 - 5.3 (418 - 540, 14.8 - 19.1)
Slip ring minimum outer diameter
[mm (in)]
More than 22.1 (0.870)
Rotor (Field coil) resistance
[
Ω
]
1.7 - 2.0
CL-1
TRANSMISSION & DRIVELINE
C
E
F
G
H
I
J
K
L
M
SECTION
CL
A
B
CL
N
O
P
CONTENTS
CLUTCH
SYMPTOM DIAGNOSIS . . . . . . . ...
NOISE, VIBRATION AND HARSHNESS
(NVH) TROUBLESHOOTING . . . . . . . .
NVH Troubleshooting Chart . . . . . . . . . ..
PRECAUTION . . . . . . . . . . . ...
PRECAUTIONS . . . . . . . . . . . . ...
Service Notice or Precautions for Clutch . . . . ..
PREPARATION . . . . . . . . . . .
PREPARATION . . . . . . . . . . . . ...
Special Service Tools . . . . . . . . . . . ....
Commercial Service Tools . . . . . . . . . ....
ON-VEHICLE MAINTENANCE . . . . . .
CLUTCH PEDAL . . . . . . . . . . . . .
Inspection and Adjustment . . . . . . . . . ....
CLUTCH FLUID . . . . . . . . . . . . ...
Air Bleeding Procedure . . . . . . . . . . .....
ON-VEHICLE REPAIR . . . . . . . . ..
CLUTCH PEDAL . . . . . . . . . . . . .
Exploded View . . . . . . . . . . . . . . ..
Removal and Installation . . . . . . . . . . ...
Inspection . . . . . . . . . . . . . . . . ..
CLUTCH MASTER CYLINDER . . . . . . ...
Exploded View . . . . . . . . . . . . . . ..
Removal and Installation . . . . . . . . . . ..
Disassembly and Assembly . . . . . . . . . .
Inspection . . . . . . . . . . . . . . . .
CLUTCH PIPING . . . . . . . . . . . ...
Exploded View . . . . . . . . . . . . . . .
Hydraulic Layout . . . . . . . . . . . . . ..
Removal and Installation . . . . . . . . . . .
REMOVAL AND INSTALLATION . . . ...
CSC (CONCENTRIC SLAVE CYLINDER) . ...
Exploded View . . . . . . . . . . . . . . .
Removal and Installation . . . . . . . . . . .
CLUTCH DISC AND CLUTCH COVER . . .
Exploded View . . . . . . . . . . . . . . .
Removal and Installation . . . . . . . . . . .
Inspection . . . . . . . . . . . . . . . .
SERVICE DATA AND SPECIFICATIONS
(SDS) . . . . . . . . . . . . . . .
SERVICE DATA AND SPECIFICATIONS
(SDS) . . . . . . . . . . . . . . . . .
Clutch Control System . . . . . . . . . . . .
Clutch Pedal . . . . . . . . . . . . . . .
Clutch Master Cylinder . . . . . . . . . . .
Clutch Disc . . . . . . . . . . . . . . . ..
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст