Infiniti G35 (V35) Sedan. Manual — part 420
DLN-114
< ON-VEHICLE REPAIR >
[FRONT FINAL DRIVE: F160A]
SIDE OIL SEAL
RIGHT SIDE : Removal and Installation
INFOID:0000000000957350
REMOVAL
1.
Remove the front drive shaft. Refer to
2.
Remove the side oil seal using a puller (A) [SST: KV381054S0
(J-34286)].
CAUTION:
Never damage gear carrier.
INSTALLATION
1.
Apply multi-purpose grease to sealing lips of side oil seal.
2.
Using the drift (A) [SST: ST33400001 (J-26082)], press-fit side
oil seal so that its surface comes face to face with the end sur-
face of the side retainer.
CAUTION:
• Never reuse oil seal.
• When installing, never incline oil seal.
3.
Install the front drive shaft. Refer to
.
4.
When oil leaks while removing, check oil level after the installa-
tion. Refer to
.
LEFT SIDE
LEFT SIDE : Exploded View
INFOID:0000000000957351
28. Pinion mate thrust washer
29. Pinion mate gear
30. Pinion mate shaft
31. Lock pin
32. Side bearing adjusting washer
33. Side oil seal (left side)
34. Side shaft bearing
35. Extension tube retainer
36. Side shaft oil seal
37. Dust sealed
38. Side shaft
A: Oil seal lip
B: Screw hole
:
Apply gear oil.
:
Apply anti-corrosion oil.
:
Apply Genuine Silicone RTV or equivalent. Refer to
GI-15, "Recommended Chemical Products and Sealants"
:
Apply Genuine Medium Strength Thread Locking Sealant or equivalent. Refer to
GI-15, "Recommended Chemical Prod-
.
Refer to
for symbols not described on the above.
PDIA0838J
PDIA0787J
SIDE OIL SEAL
DLN-115
< ON-VEHICLE REPAIR >
[FRONT FINAL DRIVE: F160A]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
1.
Drive pinion lock nut
2.
Companion flange
3.
Front oil seal
4.
Pinion front bearing
5.
Drive pinion bearing adjusting wash-
er
6.
Drive pinion adjusting washer
7.
Gear carrier
8.
Pinion rear bearing
9.
Pinion height adjusting washer
10. Drive pinion
11.
Drive gear
12. Side oil seal (right side)
13. Side retainer
14. O-ring
15. Side bearing adjusting shim
16. Side bearing
17. Differential case
18. Breather connector
19. Dowel pin
20. Filler plug
21. Drain plug
22. Gasket
23. Carrier cover
24. Gear oil defense
25. Side gear thrust washer
26. Side gear
27. Circular clip
28. Pinion mate thrust washer
29. Pinion mate gear
30. Pinion mate shaft
31. Lock pin
32. Side bearing adjusting washer
33. Side oil seal (left side)
34. Side shaft bearing
35. Extension tube retainer
36. Side shaft oil seal
37. Dust sealed
38. Side shaft
A: Oil seal lip
B: Screw hole
JSDIA0020GB
DLN-116
< ON-VEHICLE REPAIR >
[FRONT FINAL DRIVE: F160A]
SIDE OIL SEAL
LEFT SIDE : Removal and Installation
INFOID:0000000000957352
REMOVAL
1.
Remove the front final drive assembly from vehicle with power tool. Refer to
NOTE:
Left side oil seal is attached to engine assembly. Replace it after removing front final drive assem-
bly from vehicle.
2.
Remove the side oil seal using a flat-bladed screwdriver.
CAUTION:
Never damage gear carrier.
INSTALLATION
1.
Apply multi-purpose grease to sealing lips of side oil seal.
2.
Using the drift (A) [SST: KV38102100 (J-25803-01)], press-fit
side oil seal so that its surface comes face to face with the end
surface of the gear carrier.
CAUTION:
• Never reuse oil seal.
• When installing, never incline oil seal.
3.
Install the front final drive assembly on vehicle. Refer to
4.
Install the front drive shaft. Refer to
.
5.
When oil leaks while removing, check oil level after the installa-
tion. Refer to
.
:
Apply gear oil.
:
Apply anti-corrosion oil.
:
Apply Genuine Silicone RTV or equivalent. Refer to
GI-15, "Recommended Chemical Products and Sealants"
:
Apply Genuine Medium Strength Thread Locking Sealant or equivalent. Refer to
GI-15, "Recommended Chemical Prod-
.
Refer to
for symbols not described on the above.
PDIA0788J
FRONT FINAL DRIVE ASSEMBLY
DLN-117
< REMOVAL AND INSTALLATION >
[FRONT FINAL DRIVE: F160A]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
REMOVAL AND INSTALLATION
FRONT FINAL DRIVE ASSEMBLY
Exploded View
INFOID:0000000000957353
Removal and Installation
INFOID:0000000000957354
REMOVAL
1.
Remove front drive shaft both. Refer to
.
2.
Remove front crossbar with power tool.
3.
Separate steering outer socket and steering knuckle. Refer to
.
4.
Remove side shaft.
5.
Remove three way catalyst (right bank) with power tool. Refer to
.
6.
Remove front propeller shaft. Refer to
.
7.
Separate power steering solenoid valve connector.
8.
Separate power steering hydraulic line. Refer to
.
9.
Remove stabilizer assembly with power tool. Refer to
10. Separate steering lower joint and steering gear assembly. Refer to
.
11. Set a suitable jack to engine.
12. Remove front suspension member with power tool. Refer to
.
13. Remove breather hose and tube.
14. Remove engine mounting bracket (RH) (Lower) and engine mounting insulator (RH) with power tool.
15. Remove final drive assembly mounting bolts with power tool and separate front final drive assembly from
engine.
INSTALLATION
Note the following, and installation is in the reverse order of removal.
1.
Breather tube
2.
Breather hose
3.
Front final drive assembly
4.
Bushing
5.
Side shaft
: Vehicle front
Refer to
JSDIA0017GB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст