Infiniti G35 (V35) Sedan. Manual — part 1331
TM-16
< ON-VEHICLE MAINTENANCE >
[6MT: FS6R31A]
M/T OIL
ON-VEHICLE MAINTENANCE
M/T OIL
Exploded View
INFOID:0000000000956955
.
Draining
INFOID:0000000000956956
1.
Start the engine and warm up the transmission unit sufficiently.
2.
After stopping engine, remove filler plug and drain plug to drain oil.
3.
Set a gasket on drain plug and install it to transmission. Tighten drain plug to the specified torque.
CAUTION:
Do not reuse gasket.
Refilling
INFOID:0000000000956957
1.
Fill new oil into the transmission to the level of the filler plug
mounting hole.
2.
After refilling oil, check oil level.
3.
Set a gasket on filler plug and then install it to transmission.
Tighten filler plug to the specified torque.
CAUTION:
Do not reuse gasket.
Inspection
INFOID:0000000000956958
LEAKAGE
• Check if oil is leaking from transmission or around it.
LEVEL
• Check oil level from filler plug mounting hole as shown in the fig-
ure.
CAUTION:
Never start engine while checking oil level.
• When screwing in filler plug, first screw into the transmission by
hand, then tighten to the specified torque.
CAUTION:
Do not reuse gasket.
Oil grade and viscosity
: Refer to
Oil capacity
: Refer to
.
PCIB0268E
PCIB0268E
REAR OIL SEAL
TM-17
< ON-VEHICLE REPAIR >
[6MT: FS6R31A]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
ON-VEHICLE REPAIR
REAR OIL SEAL
Exploded View
INFOID:0000000000956959
.
Removal and Installation
INFOID:0000000000956960
REMOVAL
1.
Remove propeller shaft assembly. Refer to
DLN-86, "Removal and Installation"
.
2.
Remove rear oil seal using a puller [SST: KV381054S0 (J-
34286)].
INSTALLATION
1.
Apply multi-purpose grease to lip of rear oil seal (1). Drive in rear
oil seal to rear extension using the drift (A) [SST: ST33400001
(J-26082)].
CAUTION:
• Do not reuse rear oil seal.
• When installing, do not incline rear oil seal.
2.
Install propeller shaft assembly. Refer to
.
CAUTION:
• If lubricant leak has occurred during the repair work,
check oil level after finishing work. Refer to
.
PCIB0194E
Dimension “H”
: 1.2 - 2.2 mm (0.047 - 0.087 in)
JPDIC0032ZZ
TM-18
< ON-VEHICLE REPAIR >
[6MT: FS6R31A]
SHIFT CONTROL
SHIFT CONTROL
Exploded View
INFOID:0000000000956961
Removal and Installation
INFOID:0000000000956962
REMOVAL
1.
Remove shift knob with the following procedure.
a.
Release metal clips on console finisher assembly. Refer to
IP-12, "Removal and Installation"
.
1.
Shift knob
2.
Insulator
3.
Seat
4.
Console finisher assembly
5.
Felt
6.
Hole cover
7.
Control lever boot B
8.
Hole insulator
9.
Control lever boot A
10. Guide plate
11.
Control lever assembly
12. Control lever spring
13. Control lever housing
14. Control rod
: Apply multi-purpose grease.
: Apply Genuine Medium Strength Thread Locking Sealant or an equivalent. Refer to
GI-15, "Recommended Chemical Prod-
.
Refer to
for symbols not described on the above.
JPDIC0001GB
SHIFT CONTROL
TM-19
< ON-VEHICLE REPAIR >
[6MT: FS6R31A]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
b.
Lift console finisher assembly and then set a suitable pliers to
control lever assembly.
CAUTION:
Put waste cloth (A) between a suitable pliers and control
lever assembly to avoid damaging control lever assembly.
c.
Set a suitable pliers to shift knob.
CAUTION:
Put waste cloth (A) between a suitable pliers and shift knob
to avoid damaging shift knob.
d.
Keeping control lever assembly in place with a suitable pliers,
loosen shift knob with a suitable pliers.
NOTE:
Remove shift knob from control lever assembly keeping a suit-
able pliers in place because a certain power to turn shift knob is
still necessary even after adhesive is peeled.
e.
Remove shift knob from control lever assembly.
2.
Remove insulator and seat from control lever assembly.
3.
Remove console finisher assembly.
4.
Remove center console assembly. Refer to
.
5.
Remove felt.
6.
Release boot from control lever housing. Then remove control
rod mounting bolt and then separate control lever assembly and
control rod.
JPDIC0002ZZ
JPDIC0003ZZ
JPDIC0004ZZ
JPDIC0005ZZ
SCIA2561J
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст