Infiniti G35 (V35) Sedan. Manual — part 627
CYLINDER HEAD
EM-107
< DISASSEMBLY AND ASSEMBLY >
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
• Before starting engine, check oil/fluid levels including engine coolant and engine oil. If less than required
quantity, fill to the specified level. Refer to
MA-10, "Fluids and Lubricants"
.
• Use procedure below to check for fuel leakage.
- Turn ignition switch “ON” (with engine stopped). With fuel pressure applied to fuel piping, check for fuel leak-
age at connection points.
- Start engine. With engine speed increased, check again for fuel leakage at connection points.
• Run engine to check for unusual noise and vibration.
• Warm up engine thoroughly to make sure there is no leakage of fuel, exhaust gases, or any oil/fluids includ-
ing engine oil and engine coolant.
• Bleed air from lines and hoses of applicable lines, such as in cooling system.
• After cooling down engine, again check oil/fluid levels including engine oil and engine coolant. Refill to the
specified level, if necessary.
Summary of the inspection items:
*: Transmission/transaxle/CVT fluid, power steering fluid, brake fluid, etc.
Disassembly and Assembly
INFOID:0000000000956285
DISASSEMBLY
1.
Remove spark plug with spark plug wrench (commercial service tool).
2.
Remove valve lifter.
• Identify installation positions, and store them without mixing them up.
3.
Remove valve collet.
• Compress valve spring with the valve spring compressor [SST:
KV10116200 (J-26336-)] (A), the attachment [SST:
KV10115900 (J26336-20)] (C) and the adapter [SST:
KV10109220 (
—
)] (B). Remove valve collet with a magnet
hand.
CAUTION:
When working, take care not to damage valve lifter holes.
4.
Remove valve spring retainer, valve spring and valve spring seat.
5.
Push valve stem to combustion chamber side, and remove valve.
• Identify installation positions, and store them without mixing them up.
6.
Remove valve oil seal using the valve oil seal puller [SST:
KV10107902 (J38959)] (A).
7.
Remove valve seat, if valve seat must be replaced.
Items
Before starting engine
Engine running
After engine stopped
Engine coolant
Level
Leakage
Level
Engine oil
Level
Leakage
Level
Other oils and fluid*
Level
Leakage
Level
Fuel
Leakage
Leakage
Leakage
Exhaust gases
—
Leakage
—
JPBIA0180ZZ
JPBIA0177ZZ
EM-108
< DISASSEMBLY AND ASSEMBLY >
CYLINDER HEAD
• Bore out old seat until it collapses. Boring should not continue beyond the bottom face of the seat
recess in cylinder head. Set the machine depth stop to ensure this. Refer to
CAUTION:
Prevent to scratch cylinder head by excessive boring.
8.
Remove valve guide, if valve guide must be replaced.
a.
To remove valve guide, heat cylinder head to 110 to 130
°
C (230
to 266
°
F) by soaking in heated oil (A).
b.
Drive out valve guide with a press [under a 20 kN (2 ton, 2.2 US
ton, 2.0 lmp ton) pressure] or a hammer and the valve guide drift
(commercial service tool).
WARNING:
Cylinder head contains heat. When working, wear protec-
tive equipment to avoid getting burned.
9.
Remove spark plug tube, as necessary.
• Using a pliers, pull spark plug tube out of cylinder head.
CAUTION:
• Take care not to damage cylinder head.
• Once removed, spark plug tube will be deformed and cannot be reused. Do not remove it unless
absolutely necessary.
ASSEMBLY
1.
If valve guide is removed in step 8 (DISASSEMBLY), install it.
Replace with oversized [0.2 mm (0.008 in)] valve guide.
a.
Using the valve guide reamer (commercial service tool) (A),
ream cylinder head valve guide hole.
JPBIA0184ZZ
SEM931C
Valve guide hole diameter (for service parts):
Intake and exhaust
: Refer to
JPBIA0185ZZ
CYLINDER HEAD
EM-109
< DISASSEMBLY AND ASSEMBLY >
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
b.
Heat cylinder head to 110 to 130
°
C (230 to 266
°
F) by soaking in
heated oil (A).
c.
Using the valve guide drift (commercial service tool), press valve
guide from camshaft side to the dimensions as in the figure.
WARNING:
Cylinder head contains heat. When working, wear protec-
tive equipment to avoid getting burned.
d.
Using the valve guide reamer (commercial service tool) (A),
apply reamer finish to valve guide.
2.
If valve seat is removed in step 7 (DISASSEMBLY), install it.
Replace with oversize [0.5 mm (0.020 in)] valve seat.
a.
Ream cylinder head recess diameter (a) for service valve seat.
• Be sure to ream in circles concentric to valve guide center.
This will enable valve to fit correctly.
b.
Heat cylinder head to 110 to 130
°
C (230 to 266
°
F) by soaking in
heated oil (A).
JPBIA0184ZZ
Projection (A)
Intake and exhaust
: Refer to
JPBIA0186ZZ
Standard
: Refer to
.
(Intake and exhaust)
JPBIA0185ZZ
Oversize
: Refer to
.
(Intake and exhaust)
JPBIA0188ZZ
JPBIA0184ZZ
EM-110
< DISASSEMBLY AND ASSEMBLY >
CYLINDER HEAD
c.
Provide valve seats cooled well with dry ice. Force fit valve seat into cylinder head.
WARNING:
Cylinder head contains heat. When working, wear protective equipment to avoid getting burned.
CAUTION:
Avoid directly touching cold valve seats.
d.
Using the valve seat cutter set (commercial service tool) or valve
seat grinder, finish seat to the specified dimensions. Refer to
CAUTION:
When using the valve seat cutter, firmly grip cutter handle
with both hands. Then, press on the contacting surface all
around the circumference to cut in a single drive. Improper
pressure on with cutter or cutting many different times may
result in stage valve seat.
e.
Using compound, grind to adjust valve fitting.
f.
Check again for normal contact. Refer to "VALVE SEAT CONTACT".
3.
Install new valve oil seals as follows:
a.
Apply new engine oil on valve oil seal joint and seal lip.
b.
Install with the valve oil seal drift [SST: KV10115600 (J-38958)]
(A) to match dimension in the figure.
4.
Install valve spring seat.
5.
Install valve.
NOTE:
Larger diameter valves are for intake side.
6.
Install valve spring (uneven pitch type).
• Install narrow pitch (B) end [paint mark (C)] to cylinder head
side (valve spring seat side).
7.
Install valve spring retainer.
SEM934C
Height (b) (Without valve spring seat installed)
Intake and exhaust
: 14.3 - 14.9 mm (0.563 - 0.587 in)
JPBIA0178ZZ
A
: Wide pitch
: Cylinder head side
Paint mark color
: Yellowish green
JPBIA0179ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст