Infiniti G35 (V35) Sedan. Manual — part 297
CCS
ICC SYSTEM DOES NOT CANCEL WHEN A/T SELECTOR LEVER SETS ON "N"
CCS-99
< SYMPTOM DIAGNOSIS >
[INTELLIGENT CRUISE CONTROL]
C
D
E
F
G
H
I
J
K
L
M
B
N
P
A
ICC SYSTEM DOES NOT CANCEL WHEN A/T SELECTOR LEVER SETS
ON "N"
Description
INFOID:0000000000965483
ICC system is not canceled even when the A/T selector lever is shifted to the “N” range while ICC system is
active.
Diagnosis Procedure
INFOID:0000000000965484
1.
CHECK INPUT “D” RANGE SWITCH SIGNAL (ICC SENSOR INTEGRATED UNIT)
With CONSULT-III
1.
Start engine.
2.
With “DATA MONITOR” of “ICC”, check if “D RANGE SW” and “NP RANGE SW” operate normally.
Is the inspection result normal?
YES
>> GO TO 6.
NO
>> GO TO 2.
2.
PERFORM SELF-DIAGNOSIS OF ICC SENSOR INTEGRATED UNIT
1.
Perform self-diagnosis of ICC sensor integrated unit.
2.
Check if DTC “CAN COMM CIRCUIT [U1000]” (DTC 100) is detected.
Is it DTC detected?
YES
>> GO TO 3.
NO
>> GO TO 4.
3.
CAN COMMUNICATION INSPECTION
Perform the CAN communication system inspection. Repair or replace the applicable item. Refer to
.
>> INSPECTION END
4.
CHECK INPUT “D” RANGE SWITCH SIGNAL (TCM)
With CONSULT-III
With “DATA MONITOR” of “A/T”, check if “SLCT LVR POSI” operates normally.
Is the inspection result normal?
YES
>> GO TO 6.
NO
>> GO TO 5.
5.
RERFORM SELF-DIAGNOSIS OF TCM
1.
Perform self-diagnosis of TCM.
2.
Repair or replace applicable item. Refer to
.
>> GO TO 7.
6.
PEPLACE ICC SENSOR INTEGRATED UNIT
1.
Replace ICC sensor integrated unit.
2.
Adjust laser beam aiming. Refer to
CCS-7, "LASER BEAM AIMING ADJUSTMENT : Special Repair
.
>> GO TO 7.
7.
CHECK ICC SYSTEM
1.
Erase DTC and perform ICC system action test. Then perform self-diagnosis of ICC sensor integrated
unit. (For the details on the ICC system action test, refer to
CCS-11, "ACTION TEST : Special Repair
Requirement (Vehicle-To-Vehicle Distance Control Mode)"
).
2.
Check that no abnormal condition is present in the ICC system.
CCS-100
< SYMPTOM DIAGNOSIS >
[INTELLIGENT CRUISE CONTROL]
ICC SYSTEM DOES NOT CANCEL WHEN A/T SELECTOR LEVER SETS ON "N"
>> INSPECTION END
CCS
CHIME DOES NOT SOUND
CCS-101
< SYMPTOM DIAGNOSIS >
[INTELLIGENT CRUISE CONTROL]
C
D
E
F
G
H
I
J
K
L
M
B
N
P
A
CHIME DOES NOT SOUND
Description
INFOID:0000000000965485
The chime may not sound occasionally in the following cases even if the distance from the vehicle ahead is
short:
• When the speed difference from that of the vehicle ahead is small (both vehicles driving at similar speed).
• When the vehicle ahead drives at faster speed (the actual distance is increasing).
• When depressing the accelerator pedal.
• Chime does not sound when the vehicle is not driving.
• Chime does not sound when the system does not detect any vehicle ahead. (Diagnose the conditions under
which the system is detecting the vehicle ahead and when the system is malfunctioning. If there is any mal-
function in detecting the vehicle ahead, check the system following the
CCS-104, "Diagnosis Procedure"
).
Diagnosis Procedure
INFOID:0000000000965486
1.
CHECK ICC WARNING CHIME
With CONSULT-III
1.
Start engine.
2.
With “ACTIVE TEST” of “ICC”, check if “ICC BUZZER” operates normally.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> GO TO 3.
2.
CHECK THE MALFUNCTION SYMPTOM DURING BUZZER OPERATION
Determine preceding vehicle detection status when malfunction occurred. If chime should have sounded: after
replacing ICC sensor integrated unit and adjust laser beam aiming.
>> INSPECTION END
3.
PERFORM SELF-DIAGNOSIS OF ICC SENSOR INTEGRATED UNIT
1.
Perform self-diagnosis of ICC sensor integrated unit.
2.
Check if DTC “CAN COMM CIRCUIT [U1000]” (DTC 100) is detected.
Is any DTC detected?
YES
>> GO TO 4.
NO
>> GO TO 5.
4.
CAN COMMUNICATION INSPECTION
Perform the CAN communication system inspection. Repair or replace applicable item. Refer to
.
>> INSPECTION END
5.
PERFORM SELF-DIAGNOSIS OF UNIFIED METER AND A/C AMP.
1.
Perform self-diagnosis of unified meter and A/C amp.
2.
Check if DTC is detected. Refer to
.
Is any DTC detected?
YES
>> GO TO 7.
NO
>> GO TO 6.
6.
CHECK COMBINATION METER CHIME OPERATION
With CONSULT-III
1.
Select “BUZZER” on “BCM”.
2.
With “ACTIVE TEST” of “BUZZER”, check if “IGN KEY WARN ALM” and “LIGHT WARN ALM” operate
normally.
Does chime sound?
YES
>> GO TO 8.
CCS-102
< SYMPTOM DIAGNOSIS >
[INTELLIGENT CRUISE CONTROL]
CHIME DOES NOT SOUND
NO
>> Replace combination meter.
7.
REPAIR OR REPLACE APPLICABLE ITEM
Repair or replace applicable item identified by the self-diagnosis result.
>> GO TO 9.
8.
REPLACE ICC SENSOR INTEGRATED UNIT.
1.
Replace ICC sensor integrated unit.
2.
Adjust laser beam aiming. Refer to
CCS-7, "LASER BEAM AIMING ADJUSTMENT : Special Repair
.
>> GO TO 9.
9.
CHECK ICC SYSTEM
1.
Erase DTC and perform ICC system action test. Then perform self-diagnosis of ICC sensor integrated
unit. (For the details on the ICC system action test, refer to
CCS-11, "ACTION TEST : Special Repair
Requirement (Vehicle-To-Vehicle Distance Control Mode)"
).
2.
Check that no abnormal condition is present in the ICC system.
>> INSPECTION END
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст