Infiniti G35 (V35) Sedan. Manual — part 1107
REAR DRIVE SHAFT
RAX-13
< ON-VEHICLE REPAIR >
C
E
F
G
H
I
J
K
L
M
A
B
RAX
N
O
P
1.
Apply the specified amount of grease into joint sub-assembly (1)
serration hole until grease begins to ooze from ball groove and
serration hole.
CAUTION:
After applying grease, use a shop cloth to wipe off old
grease that has oozed out.
2.
Wrap serrated part of shaft with tape (A). Install boot band and
boot to shaft. Be careful not to damage boot.
CAUTION:
Never reuse boot and boot band.
3.
Remove the tape wrapped around the serrated on shaft.
4.
Position circular clip on groove at the shaft edge.
CAUTION:
Never reuse circular clip.
NOTE:
Drive joint inserter is recommended when installing circular clip.
5.
Align both center axles of the shaft edge and joint sub-assembly.
Then assemble shaft with circular clip joint sub-assembly.
6.
Install joint sub-assembly to shaft using plastic hammer.
CAUTION:
Confirm that joint sub-assembly is correctly engaged while
rotating drive shaft.
7.
Apply the balance of the specified amount of grease into the
boot inside from large diameter side of boot.
8.
Install the boot securely into grooves (indicated by “*” marks)
shown in the figure.
CAUTION:
If grease adheres to the boot mounting surface (with “*”
mark) on the shaft or housing, boot may come off. Remove
all grease from the surfaces.
9.
To prevent from deformation of the boot, adjust the boot installa-
tion length to the specified value shown below (L) by inserting
the suitable tool into inside of the boot from the large diameter
side of boot and discharging the inside air.
CAUTION:
• If the boot installation length is outside the standard, it may cause breakage in boot.
• Be careful not to touch the inside of the boot with the tip of tool.
JPDIF0008ZZ
Standard
Grease amount
: Refer to
.
JPDIF0009ZZ
RAC0049D
Standard
Boots installed
length (L)
: Refer to
.
JPDIF0018ZZ
RAX-14
< ON-VEHICLE REPAIR >
REAR DRIVE SHAFT
10. Secure the large and small ends of the boot with boot bands
using the boot band crimping tool (A) [SST: KV40107300 (
−
)].
NOTE:
Secure boot band so that dimension (M) meets the specification
as shown in the figure.
11. Secure joint sub-assembly and shaft, and then make sure that
they are in the correct position when rotating boot. Install them
with boot band when boot installation positions become incor-
rect.
12. Install dust shield to drive shaft.
Inspection
INFOID:0000000000957511
INSPECTION AFTER REMOVAL
• Move joint up/down, left/right, and in the axial direction. Check for any rough movement or significant loose-
ness.
• Check boot for cracks or other damage, and also for grease leak-
age.
• If a malfunction is found, disassemble drive shaft, and then replace
with new one.
PDIA1187J
Dimension “M”
: 2.0 – 3.0 mm (0.079 – 0.118 in)
DSF0047D
RAA0030D
SERVICE DATA AND SPECIFICATIONS (SDS)
RAX-15
< SERVICE DATA AND SPECIFICATIONS (SDS)
C
E
F
G
H
I
J
K
L
M
A
B
RAX
N
O
P
SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
Wheel Bearing
INFOID:0000000000957512
Drive Shaft
INFOID:0000000000957513
Axial end play
0.05 mm (0.002 in) or less
Joint
Wheel side
Final drive side
Grease quantity
115 – 125 g (4.06 – 4.41 oz)
124 – 134 g (4.37 – 4.73 oz)
Boots installed length
150.68 mm (5.93 in)
155 mm (6.10 in)
RF-1
BODY EXTERIOR, DOORS, ROOF & VEHICLE SECURITY
C
D
E
F
G
H
I
J
L
M
SECTION
RF
A
B
RF
N
O
P
CONTENTS
ROOF
BASIC INSPECTION . . . . . . . . .
DIAGNOSIS AND REPAIR WORKFLOW . . ..
Work Flow . . . . . . . . . . . . . . . .....
INSPECTION AND ADJUSTMENT . . . . . .
ADDITIONAL SERVICE WHEN REPLACING
CONTROL UNIT . . . . . . . . . . . . . . ..
ADDITIONAL SERVICE WHEN REPLACING
CONTROL UNIT : Description . . . . . . . . ..
ADDITIONAL SERVICE WHEN REPLACING
CONTROL UNIT : Special Repair Requirement . ...
FUNCTION DIAGNOSIS . . . . . . . ...
SUNROOF SYSTEM . . . . . . . . . . ...
System Diagram . . . . . . . . . . . . . ...
System Description . . . . . . . . . . . . ...
Component Parts Location . . . . . . . . . ..
Component Description . . . . . . . . . . ....
DIAGNOSIS SYSTEM (BCM) . . . . . . . .
COMMON ITEM . . . . . . . . . . . . . . ...
COMMON ITEM : CONSULT-III Function (BCM -
COMMON ITEM) . . . . . . . . . . . . . ...
RETAIND PWR . . . . . . . . . . . . . . ....
RETAIND PWR : CONSULT-III Function (BCM -
RETAINED PWR) . . . . . . . . . . . . .....
COMPONENT DIAGNOSIS . . . . . . ..
POWER SUPPLY AND GROUND CIRCUIT . ...
SUNROOF MOTOR ASSEMBLY . . . . . . . ....
SUNROOF MOTOR ASSEMBLY : Description . ....
SUNROOF MOTOR ASSEMBLY :
Component Function Check . . . . . . . . ....
SUNROOF MOTOR ASSEMBLY :
Diagnosis Procedure . . . . . . . . . . . ....
SUNROOF MOTOR ASSEMBLY : Component In-
spection . . . . . . . . . . . . . . . . ...
SUNROOF MOTOR ASSEMBLY : Special Repair
Requirement . . . . . . . . . . . . . . .
DOOR SWITCH . . . . . . . . . . . . .
Description . . . . . . . . . . . . . . . ...
Component Function Check . . . . . . . . .
Diagnosis Procedure . . . . . . . . . . . ...
Component Inspection . . . . . . . . . . . .
ECU DIAGNOSIS . . . . . . . . . . .
BCM (BODY CONTROL MODULE) . . . . .
Reference Value . . . . . . . . . . . . . ..
Wiring Diagram— SUNROOF CONTROL SYS-
TEM — . . . . . . . . . . . . . . . . .
Fail Safe . . . . . . . . . . . . . . . . ..
DTC Inspection Priority Chart . . . . . . . ...
DTC Index . . . . . . . . . . . . . . . ...
SUNROOF SYSTEM . . . . . . . . . . .
SUNROOF MOTOR ASSEMBLY . . . . . . . ..
SUNROOF MOTOR ASSEMBLY : Reference Val-
ue . . . . . . . . . . . . . . . . . . . .
SUNROOF MOTOR ASSEMBLY : Wiring Dia-
gram— SUNROOF CONTROL SYSTEM — . . ...
SYMPTOM DIAGNOSIS . . . . . . . ..
SUNROOF DOES NOT OPERATE PROPER-
LY . . . . . . . . . . . . . . . . . ..
Diagnosis Procedure . . . . . . . . . . . ...
AUTO OPERATION DOES NOT OPERATE .
Diagnosis Procedure . . . . . . . . . . . ...
DOES NOT STOP FULLY-OPEN OR FULLY-
CLOSED POSITION . . . . . . . . . . ..
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст