Infiniti G35 (V35) Sedan. Manual — part 738
GW-10
< ON-VEHICLE REPAIR >
WINDSHIELD GLASS
ON-VEHICLE REPAIR
WINDSHIELD GLASS
Exploded View
INFOID:0000000000961514
Removal and Installation
INFOID:0000000000961515
REMOVAL
1.
Remove the front pillar garnish. Refer to
INT-13, "Removal and Installation"
.
2.
Partially remove the headlining (front edge). Refer to
INT-23, "Removal and Installation"
3.
Remove the cowl top cover. Refer to
EXT-18, "Removal and Installation"
.
4.
Remove roof side molding. Refer to
EXT-28, "Removal and Installation"
.
5.
Apply protective tape around the windshield glass to protect the painted surface from damage.
JMKIA0001GB
1.
Windshield glass
2.
Spacer
3.
Windshield molding
4.
Dam rubber (upper, lower)
5.
Mirror base
6.
Roof panel
7.
Primer
8.
Body side outer panel
9.
Dash upper cross member
10. Cowl top cover
11.
Adhesive
12. Insulator
Refer to
for symbols in the figure.
WINDSHIELD GLASS
GW-11
< ON-VEHICLE REPAIR >
C
D
E
F
G
H
I
J
L
M
A
B
GW
N
O
P
6.
After removing moldings, remove glass using piano wire or power cutting tool (A) and an inflatable pump
bag (B).
NOTE:
If a windshield glass is to be reused, mark the body and the glass with matching marks.
WARNING:
When cutting the glass from the vehicle, always wear safety glasses and heavy gloves to help pre-
vent glass splinters from entering your eyes or cutting your hands.
CAUTION:
• When a windshield glass is to be reused, do not use a cutting knife or power cutting tool.
• Do not scratch the glass when removing.
• Do not set or stand the glass on its edge. Small chips may develop into cracks.
INSTALLATION
• The dam rubber and insulator should be installed in position.
• Use a genuine Nissan Urethane Adhesive Kit (if available) or equivalent and follow the instructions furnished
with it.
• While the urethane adhesive is curing, open a door window. This will prevent the glass from being forced out
by passenger room air pressure when a door is closed.
• The molding must be installed securely so that it is in position and leaves no gap.
• Inform the customer that the vehicle should remain stationary until the urethane adhesive has completely
cured (preferably 24 hours). Curing time varies with temperature and humidity.
WARNING:
• Keep heat and open flames away as primers and adhesive are flammable.
• The materials contained in the kit are harmful if swallowed, and may irritate skin and eyes. Avoid
contact with the skin and eyes.
• Use in an open, well ventilated location. Avoid breathing the vapors. They can be harmful if inhaled.
If affected by vapor inhalation, immediately move to an area with fresh air.
• Driving the vehicle before the urethane adhesive has completely cured may affect the performance
of the windshield in case of an accident.
CAUTION:
• Do not use an adhesive which is past its usable term. Shelf life of this product is limited to six
months after the date of manufacture. Carefully adhere to the expiration or manufacture date printed
on the box.
• Keep primers and adhesive in a cool, dry place. Ideally, they should be stored in a refrigerator.
• Do not leave primers or adhesive cartridge unattended with their caps open or off.
• The vehicle should not be driven for at least 24 hours or until the urethane adhesive has completely
cured. Curing time varies depending on temperature and humidity. The curing time will increase
under lower temperature and lower humidity.
Inspection
INFOID:0000000000961516
Repairing Water Leakage for Windshield
Leakage can be repaired without removing and reinstalling glass.
If water is leaking between the urethane adhesive material and body or glass, determine the extent of leakage.
This can be done by applying water to the windshield area while pushing glass outward.
To stop the leakage, apply primer (if necessary) and then urethane adhesive to the leakage point.
PIIB5779E
GW-12
< ON-VEHICLE REPAIR >
REAR WINDOW GLASS
REAR WINDOW GLASS
Exploded View
INFOID:0000000000961517
Removal and Installation
INFOID:0000000000961518
REMOVAL
1.
Remove rear seat back and rear seat cushion. Refer to
SE-105, "Removal and Installation"
2.
Remove the rear pillar finisher. Refer to
INT-13, "Removal and Installation"
.
3.
Remove the rear parcel shelf finisher. Refer to
INT-18, "Removal and Installation"
.
4.
Remove the rear of the headlining. Refer to
INT-23, "Removal and Installation"
.
5.
Remove the connectors and grounds for the rear window defogger and printed antenna.
1.
Rear window glass
2.
Dam rubber
3.
Spacer
4.
Roof panel
5.
Primer
6.
Adhesive
7.
Body side outer panel
8.
Waist rear
Refer to
for symbols in the figure.
JMKIA0002GB
REAR WINDOW GLASS
GW-13
< ON-VEHICLE REPAIR >
C
D
E
F
G
H
I
J
L
M
A
B
GW
N
O
P
6.
After removing molding using pliers, remove glass using piano wire or power cutting tool (A) and an inflat-
able pump bag (B).
7.
If a rear window glass is reused, mark the body and the glass with matching marks.
WARNING:
When cutting the glass from the vehicle, always wear safety glasses and heavy gloves to help pre-
vent glass splinters from entering your eyes or cutting your hands.
CAUTION:
• When a rear window glass is reused, do not use a cutting knife or power cutting tool.
• Do not scratch the glass when removing.
• Do not set or stand the glass on its edge. Small chips may develop into cracks.
INSTALLATION
• The dam rubber should be installed in position.
• Use a genuine Nissan Urethane Adhesive Kit (if available) or equivalent and follow the instructions furnished
with it.
• While the urethane adhesive is curing, open a door window. This will prevent the glass from being forced out
by passenger compartment air pressure when a door is closed.
• The molding must be installed securely so that it is in position and leaves no gap.
• Inform the customer that the vehicle should remain stationary until the urethane adhesive has completely
cured (preferably 24 hours). Curing time varies with temperature and humidity.
WARNING:
• Keep heat and open flames away as primers and adhesive are flammable.
• The materials contained in the kit are harmful if swallowed, and may irritate skin and eyes. Avoid
contact with the skin and eyes.
• Use in an open, well ventilated location. Avoid breathing the vapors. They can be harmful if
inhaled. If affected by vapor inhalation, immediately move to an area with fresh air.
• Driving the vehicle before the urethane adhesive has completely cured may affect the performance
of the rear window in case of an accident.
CAUTION:
• Do not use an adhesive which is past its usable term. Shelf life of this product is limited to six
months after the date of manufacture. Carefully adhere to the expiration or manufacture date
printed on the box.
• Keep primers and adhesive in a cool, dry place. Ideally, they should be stored in a refrigerator.
• Do not leave primers or adhesive cartridge unattended with their caps open or off.
• The vehicle should not be driven for at least 24 hours or until the urethane adhesive has com-
pletely cured. Curing time varies depending on temperature and humidity. The curing time will
increase under lower temperature and lower humidity.
Inspection
INFOID:0000000000961519
REPAIRING WATER LEAKAGE
Leakage can be repaired without removing and reinstalling glass.
If water is leaking between the urethane adhesive material and body or glass, determine the extent of leakage.
This can be done by applying water to the side window area while pushing glass outward.
To stop the leakage, apply primer (if necessary) and then urethane adhesive to the leakage point.
PIIB5779E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст