Infiniti G35 (V35) Sedan. Manual — part 35
ADP-134
< COMPONENT DIAGNOSIS >
DOOR MIRROR MOTOR
DOOR MIRROR MOTOR
Description
INFOID:0000000000960747
It makes mirror face operate from side to side and up and down with the electric power that AUTOMATIC
DRIVE POSITIONER CONTROL UNIT supplies.
Component Function Check
INFOID:0000000000960748
1.
CHECK DOOR MIRROR MOTOR FUNCTION
Check the operation with “MIRROR MOTOR RH” and “MIRROR MOTOR LH” in “ACTIVE TEST” mode with
CONSULT-III
Refer to
ADP-48, "CONSULT-III Function"
.
Is the inspection result normal?
YES
>> Door mirror motor function is OK.
NO
>> Refer to
ADP-134, "Diagnosis Procedure"
Diagnosis Procedure
INFOID:0000000000960749
1.
CHECK DOOR MIRROR MOTOR INPUT SIGNAL
1.
Turn ignition switch ON.
2.
Check voltage between door mirror connector and ground.
Is the inspection result normal?
YES
>> Refer to
ADP-136, "Component Inspection"
.
NO
>> GO TO 2.
2.
CHECK HARNESS CONTINUITY
1.
Turn ignition switch OFF.
2.
Disconnect automatic drive positioner control unit connector and door mirror connector.
3.
Check continuity between automatic drive positioner control unit connector and door mirror connector.
[Door mirror driver side]
[Door mirror passenger side]
Terminals
Door mirror remote control switch
condition
Voltage (V)
(Approx.)
(+)
(–)
Door mirror
connector
Terminal
D3 (Driver side)
D33 (Passenger side)
5
Ground
UP
Battery voltage
Other than above
0
6
LEFT
Battery voltage
Other than above
0
7
DOWN / RIGHT
Battery voltage
Other than above
0
Automatic drive positioner con-
trol unit connector
Terminal
Door mirror (driver side) connec-
tor
Terminal
Continuity
M51
16
D3
7
Existed
31
5
32
6
Automatic drive positioner control
unit connector
Terminal
Door mirror (passenger side)
connector
Terminal
Continuity
M51
14
D33
5
Existed
15
6
30
7
DOOR MIRROR MOTOR
ADP-135
< COMPONENT DIAGNOSIS >
C
D
E
F
G
H
I
K
L
M
A
B
ADP
N
O
P
4.
Check continuity between automatic drive positioner control unit connector and ground.
[Door mirror driver side]
[Door mirror passenger side]
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace harness.
3.
CHECK AUTOMATIC DRIVE POSITIONER CONTROL UNIT OUTPUT SIGNAL
1.
Connect automatic drive positioner control unit connector.
2.
Turn ignition switch ON.
3.
Check voltage between automatic drive positioner control unit connector and ground.
[Door mirror driver side]
[Door mirror passenger side]
Is the inspection result normal?
YES
>> Refer to
ADP-136, "Component Inspection"
.
NO
>> Replace automatic drive positioner control unit. Refer to
ADP-218, "Removal and Installation"
.
4.
CHECK DOOR MIRROR MOTOR
Check door mirror motor.
Refer to
ADP-136, "Component Inspection"
.
Automatic drive positioner control unit connec-
tor
Terminal
Ground
Continuity
M51
16
Not existed
31
32
Automatic drive positioner control unit connec-
tor
Terminal
Ground
Continuity
M51
14
Not existed
15
30
Terminals
Mirror switch condition
Voltage (V)
(Approx.)
(+)
(-)
Automatic drive positioner con-
trol unit connector
Terminal
M51
16
Ground
DOWN / RIGHT
Battery voltage
Other than above
0
31
UP
Battery voltage
Other than above
0
32
LEFT
Battery voltage
Other than above
0
Terminals
Mirror switch condition
Voltage (V)
(Approx.)
(+)
(-)
Automatic drive positioner con-
trol unit connector
Terminal
M51
14
Ground
UP
Battery voltage
Other than above
0
15
LEFT
Battery voltage
Other than above
0
30
DOWN / RIGHT
Battery voltage
Other than above
0
ADP-136
< COMPONENT DIAGNOSIS >
DOOR MIRROR MOTOR
Is the inspection result normal?
YES
>> Refer to
GI-39, "Intermittent Incident"
.
NO
>> Replace door mirror. Refer to
MIR-67, "Removal and Installation"
.
Component Inspection
INFOID:0000000000960750
1.
CHECK DOOR MIRROR MOTOR-I
Check that door mirror motor does not trap foreign objects and does not have any damage.
Refer to
.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Replace door mirror.Refer to
MIR-67, "Removal and Installation"
2.
CHECK DOOR MIRROR MOTOR-II
1.
Turn ignition switch OFF.
2.
Disconnect door mirror connector.
3.
Apply 12V to each power supply terminal of door mirror motor.
Is the inspection result normal?
YES
>> INSPECTION END.
NO
>> Replace door mirror. Refer to
MIR-67, "Removal and Installation"
.
Door mirror connector
Terminal
Operational direction
(+)
(–)
D3 (Driver side)
D33 (Passenger side)
7
6
RIGHT
6
7
LEFT
5
7
UP
7
5
DOWN
SIDE SUPPORT UNIT
ADP-137
< COMPONENT DIAGNOSIS >
C
D
E
F
G
H
I
K
L
M
A
B
ADP
N
O
P
SIDE SUPPORT UNIT
Description
INFOID:0000000000960751
Built-in pump, pump relay and solenoid, side support unit operates when pressing ON/OFF on side support
switch.
Component Function Check
INFOID:0000000000960752
1.
CHECK SIDE SUPPORT UNIT FUNCTION
Check side support operation with side support switch.
Is the inspection results normal?
YES
>> Side support unit is OK.
NO
>> Refer to
ADP-137, "Diagnosis Procedure"
Diagnosis Procedure
INFOID:0000000000960753
1.
CHECK SIDE SUPPORT UNIT SIGNAL CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect side support unit and side support switch connectors.
3.
Check continuity between side support unit and side support switch connector.
4.
Check continuity between side support unit and ground.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace circuit.
2.
CHECK SIDE SUPPORT UNIT GROUND CIRCUIT
Check continuity between side support unit and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace circuit.
3.
CHECK INTERMITTENT INCIDENT
Check intermittent incident.
Refer to
GI-39, "Intermittent Incident"
.
Is the inspection result normal?
YES
>> Replace side support unit.
NO
>> Repair or replace malfunction part.
Side support unit connector
Terminal
Side support switch
connector
Terminal
Continuity
B420
15
B419
15
Existed
16
16
17
17
18
18
Side support unit connector
Terminal
Ground
Continuity
B420
15
Not existed
16
17
18
Side support unit connector
Terminal
Ground
Continuity
B420
2
Existed
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст