Infiniti G35 (V35) Sedan. Manual — part 428
DLN-146
< SYMPTOM DIAGNOSIS >
[REAR FINAL DRIVE: R200]
NOISE, VIBRATION AND HARSHNESS (NVH) TROUBLESHOOTING
×
: Applicable
Reference
NVH in DLN
section.
NVH in F
AX,
RAX, FS
U and RSU sections.
NVH in WT
section.
NVH in WT
section.
NVH in F
AX and
RAX
section.
NVH in BR
section.
NVH in ST
section.
Possible cause and SUSPECTED PARTS
Ge
ar t
oot
h ro
ug
h
Ge
ar c
o
n
ta
c
t
im
prop
er
T
o
ot
h s
u
rf
ac
es
worn
Ba
ck
la
sh
in
c
o
rre
ct
Co
mp
an
io
n fl
an
ge
ex
c
e
s
s
iv
e
run
o
u
t
Ge
ar o
il
im
pro
p
e
r
PROPELLE
R
SHAFT
AX
LE A
N
D
SUSPENSION
TI
RE
S
ROAD WH
E
E
L
DRIVE
SHAFT
BRAK
ES
ST
EERING
Symptom
Noise
×
×
×
×
×
×
×
×
×
×
×
×
×
PRECAUTIONS
DLN-147
< PRECAUTION >
[REAR FINAL DRIVE: R200]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
PRECAUTION
PRECAUTIONS
Service Notice or Precautions for Rear Final Drive
INFOID:0000000000957376
CAUTION:
• Check for the correct installation status prior to removal or disassembly. If matching marks are
required, be certain they do not interfere with the function of the parts when applied.
• Overhaul should be done in a clean work area, it is preferable to work in dustproof area.
• Before disassembly, using steam or white gasoline, completely remove sand and mud from the exte-
rior of the unit, preventing them from entering into the unit during disassembly or assembly.
• Check appearance of the disassembled parts for damage, deformation, and unusual wear. Replace
them with a new ones if necessary.
• Gaskets, seals and O-rings should be replaced any time when the unit is disassembled.
• In principle, tighten bolts or nuts gradually in several steps working diagonally from inside to out-
side. If tightening sequence is specified, observe it.
• Clean and flush the parts sufficiently and blow-dry them.
• Be careful not to damage sliding surfaces and mating surfaces.
• When applying sealant, remove the old sealant from the mounting surface; then remove any mois-
ture, oil, and foreign materials from the application and mounting surfaces.
• Always use shop paper for cleaning the inside of components.
• Avoid using cotton gloves or shop rags to prevent entering of lint.
• During assembly, observe the specified tightening torque, and apply new gear oil, petroleum jelly, or
multi-purpose grease as specified for each vehicle, if necessary.
DLN-148
< PREPARATION >
[REAR FINAL DRIVE: R200]
PREPARATION
PREPARATION
PREPARATION
Special Service Tools
INFOID:0000000000957377
The actual shapes of Kent-Moore tools may differ from those of special service tools illustrated here.
Tool number
(Kent-Moore No.)
Tool name
Description
KV40104100
(
—
)
Attachment
Removing side flange
ST36230000
(J-25840-A)
Sliding hammer
Removing side flange
ST3127S000
(J-25765-A)
Preload gauge
Measuring pinion bearing preload and total
preload
KV381054S0
(J-34286)
Puller
Removing front oil seal
ST30720000
(J-25405)
Drift
a: 77 mm (3.03 in) dia.
b: 55.5 mm (2.185 in) dia.
• Installing front oil seal
• Installing pinion rear bearing outer race
KV38107900
(J-39352)
Protector
Installing side flange
ZZA0804D
ZZA0803D
ZZA0806D
ZZA0601D
ZZA0811D
S-NT129
PREPARATION
DLN-149
< PREPARATION >
[REAR FINAL DRIVE: R200]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
KV38100200
(J-26233)
Drift
a: 65 mm (2.56 in) dia.
b: 49 mm (1.93 in) dia.
Installing side oil seal
KV10111100
(J-37228)
Seal cutter
Removing rear cover
KV38100800
(J-25604-01)
Attachment
a: 541 mm (21.30 in)
b: 200 mm (7.87 in)
Fixing unit assembly
ST3306S001
(J-22888-D)
Differential side bearing puller set
1: ST33051001
(J-22888-20)
Puller
2: ST33061000
(J-8107-2)
Base
a: 28.5 mm (1.122 in) dia.
b: 38 mm (1.50 in) dia.
Removing and installing side bearing inner
race
KV38100300
(J-25523)
Drift
a: 54 mm (2.13 in) dia.
b: 46 mm (1.81 in) dia.
c: 32 mm (1.26 in) dia.
Installing side bearing inner race
(J-8129)
Spring gauge
Measuring turning torque
Tool number
(Kent-Moore No.)
Tool name
Description
ZZA1143D
S-NT046
SDIA0267E
NT072
ZZA1046D
NT127
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст