Infiniti G35 (V35) Sedan. Manual — part 1355
TM-112
< FUNCTION DIAGNOSIS >
[5AT: RE5R05A]
ON BOARD DIAGNOSTIC (OBD) SYSTEM
• The MIL is located on the combination meters.
1.
The MIL will light up when the ignition switch is turned ON with-
out the engine running. This is a bulb check. If the MIL does not
light up, refer to
EC-471, "Component Function Check"
.
2.
When the engine is started, the MIL should go off.
If the MIL remains on, the on board diagnostic system has
detected engine system malfunction.
SEF217U
DIAGNOSIS SYSTEM (TCM)
TM-113
< FUNCTION DIAGNOSIS >
[5AT: RE5R05A]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
DIAGNOSIS SYSTEM (TCM)
Diagnosis Description
INFOID:0000000000957009
TCM SELF-DIAGNOSTIC PROCEDURE (NO TOOLS)
Description
As a method for locating the suspect circuit, when the self-diagnostics start signal is input, the memory for the
malfunction location is output and the A/T CHECK indicator lamp flashes to display the corresponding DTC.
Operation Procedure
1.
CHECK A/T CHECK INDICATOR LAMP
1.
Start the engine with selector lever in “P” position. Warm engine to normal operating temperature.
2.
Turn ignition switch ON and OFF at least twice, then leave it in the OFF position.
3.
Wait 10 seconds.
4.
Turn ignition switch ON. (Do not start engine.)
Does A/T CHECK indicator lamp come on for about 2 seconds?
YES
>> GO TO 2.
NO
>> Go to
.
2.
JUDGMENT PROCEDURE
1.
Turn ignition switch OFF.
2.
Keep pressing shift lock release button.
3.
Move selector lever from “P” to “D” position.
4.
Release accelerator pedal. (Set the closed throttle position signal ON.)
5.
Depress brake pedal. (Stop lamp switch signal ON.)
6.
Turn ignition switch ON. (Do not start engine.)
7.
Wait 3 seconds.
8.
Move the selector lever to the manual shift gate side. (Manual mode signal ON.)
9.
Release brake pedal. (Stop lamp switch signal ON.)
10. Move the selector lever to “D” position. (Manual mode signal OFF.)
11. Depress brake pedal. (Stop lamp switch signal ON.)
12. Release brake pedal. (Stop lamp switch signal OFF.)
13. Depress accelerator pedal fully and release it.
>> GO TO 3.
3.
CHECK SELF-DIAGNOSIS CODE
Check A/T CHECK indicator lamp. Refer to “Judgment Self-diagnosis Code”.
If the system does not go into self-diagnosis, refer to
>> DIAGNOSIS END
Judgment Self-diagnosis Cord
TM-114
< FUNCTION DIAGNOSIS >
[5AT: RE5R05A]
DIAGNOSIS SYSTEM (TCM)
If there is a malfunction, the lamp lights up for the time corresponding to the suspect circuit.
Erase Self-diagnosis
In order to make it easier to find the cause of hard-to-duplicate malfunctions, malfunction information is stored
into the control unit as necessary during use by the user. This memory is not erased no matter how many
times the ignition switch is turned ON and OFF.
However, this information is erased by turning ignition switch OFF after performing self-diagnostics or by eras-
ing the memory using the CONSULT-III.
CONSULT-III Function (TRANSMISSION)
INFOID:0000000000957010
CONSULT-III APPLICATION ITEMS
No.
Malfunctioning item
No.
Malfunctioning item
1
Revolution sensor
12
2
Direct clutch solenoid valve
13
A/T 1st engine braking
3
Torque converter clutch solenoid valve
14
4
Line pressure solenoid valve
15
Accelerator pedal position sensor
5
16
6
Front brake solenoid valve
17
CAN communication line
7
Low coast brake solenoid valve
18
1st gear function
8
High and low reverse clutch solenoid valve
19
2nd gear function
9
PNP switch
20
3rd gear function
10
A/T fluid temperature sensor
21
gear
11
Turbine revolution sensor
22
JPDIA0024GB
DIAGNOSIS SYSTEM (TCM)
TM-115
< FUNCTION DIAGNOSIS >
[5AT: RE5R05A]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
SELF-DIAGNOSTIC RESULTS
Display Items List
X: Applicable, —: Not applicable
Diagnostic test mode
Function
Work support
This mode enables a technician to adjust some devices faster and more accurately by following the in-
dications on CONSULT-III.
Self-diagnostic results
Self-diagnostic results can be read and erased quickly.
Data monitor
Input/Output data in the ECU can be read.
CAN diagnostic support mon-
itor
The results of transmit/receive diagnosis of CAN communication can be read.
Function test
Performed by CONSULT-III instead of a technician to determine whether each system is “OK” or “NG”.
DTC work support
The operating condition to confirm Diagnostic Trouble Codes can be selected.
ECU part number
TCM part number can be read.
Items (CONSULT-III screen terms)
TCM self-diagnosis
OBD-II (DTC)
Reference page
“A/T” with CONSULT-III
MIL
*1
, “ENGINE” with CON-
SULT-III or GST
CAN COMM CIRCUIT
U1000
U1000
STARTER RELAY/CIRC
P0615
—
TCM
P0700
P0700
PNP SW/CIRC
P0705
P0705
TURBINE REV S/CIRC
P0717
P0717
VEH SPD SEN/CIR AT
P0720
P0720
ENGINE SPEED SIG
P0725
P0725
AT 1ST GR FNCTN
P0731
P0731
AT 2ND GR FNCTN
P0732
P0732
AT 3RD GR FNCTN
P0733
P0733
AT 4TH GR FNCTN
P0734
P0734
AT 5TH GR FNCTN
P0735
P0735
TCC SOLENOID/CIRC
P0740
P0740
A/T TCC S/V FNCTN
P0744
P0744
*2
L/PRESS SOL/CIRC
P0745
P0745
TP SEN/CIRC A/T
P1705
—
ATF TEMP SEN/CIRC
P1710
P0710
VEH SPD SE/CIR-MTR
P1721
—
A/T INTERLOCK
P1730
P1730
A/T 1ST E/BRAKING
P1731
—
I/C SOLENOID/CIRC
P1752
P1752
FR/B SOLENOID/CIRC
P1757
P1757
D/C SOLENOID/CIRC
P1762
P1762
HLR/C SOL/CIRC
P1767
P1767
LC/B SOLENOID/CIRC
P1772
P1772
LC/B SOLENOID FNCT
P1774
P1774
MANU MODE SW/CIRC
P1815
—
NO DTC IS DETECTED FURTHER
TESTING MAY BE REQUIRED
X
X
—
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст