Infiniti G35 (V35) Sedan. Manual — part 611
OIL PAN (LOWER)
EM-43
< ON-VEHICLE REPAIR >
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
a.
Loosen mounting bolts in reverse order as shown in the figure to
remove.
b.
Insert the seal cutter [SST: KV10111100 (J37228)] (A) between
oil pan (upper) and oil pan (lower).
CAUTION:
• Be careful not to damage the mating surfaces.
• Do not insert a screwdriver, this will damage the mating
surfaces.
c.
Slide the seal cutter by tapping on the side of tool with a ham-
mer. Remove oil pan (lower).
INSTALLATION
1.
Install oil pan (lower) as follows:
a.
Use scraper (A) to remove old liquid gasket from mating sur-
faces.
• Remove old liquid gasket from the bolt holes and thread.
CAUTION:
Do not scratch or damage the mating surfaces when clean-
ing off old liquid gasket.
b.
Apply a continuous bead of liquid gasket with the tube presser
[SST: WS39930000 (
—
)] (A) to the oil pan (lower) as shown
in the figure.
Use Genuine RTV Silicone Sealant or equivalent. Refer to
GI-15, "Recommended Chemical Products and Sealants"
.
CAUTION:
Attaching should be done within 5 minutes after coating.
c.
Install oil pan (lower).
: Engine front
JPBIA0021ZZ
JPBIA0276ZZ
JPBIA0025ZZ
b
: 4.0 - 5.0 mm (0.157 - 0.197 in)
JPBIA0026ZZ
EM-44
< ON-VEHICLE REPAIR >
OIL PAN (LOWER)
• Tighten mounting bolts in numerical order as shown in the fig-
ure.
2.
Install oil pan drain plug.
• Refer to the figure of components of former page for installation direction of drain plug washer. Refer to
3.
Install in the reverse order of removal after this step.
NOTE:
At least 30 minutes after oil pan is installed, pour engine oil.
Inspection
INFOID:0000000000956253
INSPECTION AFTER REMOVAL
Clean oil strainer if any object attached.
INSPECTION AFTER INSTALLATION
1.
Check the engine oil level and adjust engine oil. Refer to
2.
Start engine, and check there is no leak of engine oil.
3.
Stop engine and wait for 10 minutes.
4.
Check the engine oil level again. Refer to
.
: Engine front
JPBIA0021ZZ
IGNITION COIL, SPARK PLUG AND ROCKER COVER
EM-45
< ON-VEHICLE REPAIR >
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
IGNITION COIL, SPARK PLUG AND ROCKER COVER
Exploded View
INFOID:0000000000956254
Removal and Installation
INFOID:0000000000956255
REMOVAL
1.
Remove the following parts:
• Engine cover: Refer to
• Air cleaner case and air duct (RH and LH): Refer to
• Intake manifold collector: Refer to
.
2.
Disconnect PCV hose from rocker cover.
1.
PCV hose
2.
Clamp
3.
Ignition coil
4.
Spark plug
5.
PCV valve
6.
O-ring
7.
Rocker cover gasket (right bank)
8.
Rocker cover (right bank)
9.
O-ring
10.
Camshaft position sensor (PHASE)
(bank 1)
11.
Exhaust valve timing control position
sensor (bank 1)
12.
Camshaft position sensor (PHASE)
(bank 2)
13.
Exhaust valve timing control position
sensor (bank 2)
14.
Rocker cover gasket (left bank)
15. Rocker cover (left bank)
16.
PCV hose
17.
Oil catcher
18. Oil filler cap
19.
PCV hose
A.
To intake manifold collector
B.
Refer to
C.
Camshaft bracket side
D.
To air duct
Refer to
for symbol marks in the figure.
JPBIA0009ZZ
EM-46
< ON-VEHICLE REPAIR >
IGNITION COIL, SPARK PLUG AND ROCKER COVER
3.
Remove camshaft position sensor (PHASE) and exhaust valve
timing control position sensor (bank 1 and bank 2).
CAUTION:
• Handle carefully to avoid dropping and shocks.
• Do not disassemble
• Do not allow metal powder to adhere to magnetic part at
sensor tip.
• Do not place sensors in a location where they are
exposed to magnetism.
4.
Remove PCV valve and O-ring from rocker cover, if necessary.
5.
Remove oil filler cap from rocker cover, if necessary.
6.
Remove ignition coil.
CAUTION:
Do not shock it.
7.
Remove harness clips on the rocker cover.
8.
Loosen bolts in reverse order shown in the figure.
9.
Remove rocker cover gasket from rocker cover.
10. Use scraper to remove all traces of liquid gasket from cylinder
head and camshaft bracket (No. 1).
CAUTION:
Do not scratch or damage the mating surface when clean-
ing off old liquid gasket.
INSTALLATION
A
: Keep off any magnetic materials
: Engine front
JPBIA0454ZZ
JPBIA0040ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст