Infiniti G35 (V35) Sedan. Manual — part 1422
VTL-26
< ON-VEHICLE REPAIR >
IN-VEHICLE SENSOR
IN-VEHICLE SENSOR
Exploded View
INFOID:0000000000959794
Removal and Installation
INFOID:0000000000959795
REMOVAL
1.
Remove instrument driver lower panel. Refer to
IP-12, "Removal and Installation"
.
2.
Remove mounting screw (A), and then remove in-vehicle sensor
(1).
INSTALLATION
Installation is basically the reverse order of removal.
1.
In-vehicle sensor
2.
instrument driver lower panel
JSIIA0126ZZ
JSIIA0032ZZ
SUNLOAD SENSOR
VTL-27
< ON-VEHICLE REPAIR >
C
D
E
F
G
H
J
K
L
M
A
B
VTL
N
O
P
SUNLOAD SENSOR
Exploded View
INFOID:0000000000959796
Removal and Installation
INFOID:0000000000959797
REMOVAL
1.
Remove front defroster grille (left). Refer to
IP-12, "Removal and Installation"
2.
Disconnect sunload sensor connector, and then remove sunload
sensor (1).
INSTALLATION
Installation is basically the reverse order of removal.
1.
Sunload sensor
JSIIA0218ZZ
JSIIA0050ZZ
VTL-28
< ON-VEHICLE REPAIR >
INTAKE SENSOR
INTAKE SENSOR
Exploded View
INFOID:0000000000959798
1.
Aspirator
2.
Aspirator hose
3.
Front heater duct
4.
Foot duct (left)
5.
Defroster seal
6.
Packing
7.
Ventilator seal
8.
Ventilator door (left)
9.
Ventilator door (right)
10. Foot duct (right)
11.
Defroster door lever
12.
Foot door lever
13. Ventilator door lever
14.
Ventilator door link
15.
Main link
16. Mode door motor bracket
17.
Mode door motor
18.
Air mix door motor (passenger side)
19. Intake sensor
20.
Intake sensor bracket
21.
O-ring
22. Low-pressure pipe 1
23.
High-pressure pipe 2
24.
Expansion valve
25. Cooler pipe grommet
26.
Insulator
27.
Evaporator cover adapter
28. Heater pipe bracket
29.
Case packing
30.
Heater & cooling unit case (left)
31. Heater pipe grommet
32.
Heater core
33.
Air mix door motor (driver side)
*
34. Foot door (left)
35.
Rear ventilator door
36.
Foot door (right)
JSIIA0016GB
INTAKE SENSOR
VTL-29
< ON-VEHICLE REPAIR >
C
D
E
F
G
H
J
K
L
M
A
B
VTL
N
O
P
Removal and Installation
INFOID:0000000000959799
REMOVAL
1.
Remove low-pressure pipe 1 and high-pressure pipe 2. Refer to
HA-51, "Removal and Installation"
CAUTION:
Cap or wrap the joint of low-pressure pipe 1, 2 and high-pressure pipe 1, 2 with suitable material
such as vinyl tape to avoid the entry of air.
2.
Slide evaporator (1) to passenger side, and then remove intake
sensor (2).
INSTALLATION
Installation is basically the reverse order of removal.
CAUTION:
• Replace O-rings of low-pressure pipe 1, 2 and high-pressure pipe 1, 2 with new ones, and then apply
compressor oil to it when installing it.
• Mark the mounting position of intake sensor bracket prior to removal so that the reinstalled sensor
can be located in the same position.
• Female-side piping connection is thin and easy to deform. Slowly insert the male-side piping
straight in axial direction.
• Insert piping securely until a click is heard.
• After piping connection is completed, pull male-side piping by hand to make sure that connection
does not come loose.
• When recharging refrigerant, check for leaks.
37.
Max. cool door lever
38.
Foot door link
39. Defroster door link
40.
Max. cool door link
41.
Main link sub
42. Evaporator cover
43.
Heater & cooling unit case (right)
44.
Evaporator
45. Drain hose
46.
Clamp
47.
Air mix door (Slide door)
48. Air mix door adapter
49.
Heater pipe cover
50.
Max. cool door (left)
51. Defroster door (left)
52.
Center case
53.
Defroster door (right)
54. Max. cool door (right)
*
With left and right ventilation temperature separately system.
Refer to
for symbols in the figure.
JSIIA0052ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст