Infiniti G35 (V35) Sedan. Manual — part 143
AV-344
< FUNCTION DIAGNOSIS >
[BOSE AUDIO WITH NAVIGATION]
DIAGNOSIS SYSTEM (AV CONTROL UNIT)
AV COMM Diagnosis
• Displays the communication status between AV control unit (mas-
ter unit) and each unit.
• The error counter displays “OK” if any malfunction was not
detected in the past and displays “0” if a malfunction is detected. It
increases by 1 if the condition is normal at the next ignition switch
ON cycle. The upper limit of the counter is 39.
• If it resets, the error counter is erased.
NOTE:
• Any units with “—” displayed have no history of vehicle connection.
• “Audio” and “Amp” indicate the same status because “Amp” indicates the status of the amplifier integrated in the AV control unit.
• “STRG SW”, “Amp”“XM” indicate the same status as “Audio”.
Handsfree Phone
The hands-free phone reception volume adjustment, microphone
and speaker test, and memory erase functions are also available.
Camera Cont.
The two functions of “Connection Confirmation” and “Adjust Offset of Rear view Camera” are available.
CONNECTION CONFIRAMATION
Rx (HVAC)
OK / UNKWN
OK / 0 – 39
Rx (USM)
OK / UNKWN
OK / 0 – 39
Items
Display (Current)
Malfunction counter
(Past)
Items
Status
(Current)
Counter
(Past)
C Tx(ITM–PrimarySW)
OK / UNKWN
OK / 0 – 39
C Rx(PrimarySW–ITM)
OK / UNKWN
OK / 0 – 39
C Rx(STRG SW–ITM)
OK / UNKWN
OK / 0 – 39
C Rx (Audio–ITM)
OK / UNKWN
OK / 0 – 39
C Rx(Amp–ITM)
OK / UNKWN
OK / 0 – 39
C Rx(RearCamera–ITM)
OK / UNKWN
OK / 0 – 39
C Rx(XM–ITM)
OK / UNKWN
OK / 0 – 39
C Rx(Amp–Audio)
—
—
C Tx(Audio–ITM)
OK / UNKWN
OK / 0 – 39
JSNIA0081GB
JSNIA0083GB
AV
DIAGNOSIS SYSTEM (AV CONTROL UNIT)
AV-345
< FUNCTION DIAGNOSIS >
[BOSE AUDIO WITH NAVIGATION]
C
D
E
F
G
H
I
J
K
L
M
B
N
A
O
P
The steering angle sensor, reverse signal and vehicle speed sensor
can be inspected.
ADJUST OFFSET OF REAR VIEW CAMERA
Use this mode to adjust the guide line display position of the rear-
view monitor if necessary after removing the rear view monitor cam-
era.
Bluetooth
Passkey confirmation/change
• The passkey of Bluetooth can be confirmed and changed.
• The passkey can be changed by four digits within 0 to 9.
Device name check/change
JSNIA0084GB
Diagnosis item
Display
Vehicle status
Steer. Angle Sensor
ON
When steering the vehicle with ignition switch ON (remains ON until connection
mode is stopped when it is turned ON)
OFF
• Ignition switch at ACC
• No steering with ignition switch ON
—
Malfunction detected in camera-connection recognition signal
Reverse Sensor
ON
Selector lever is in “R” with ignition switch ON.
OFF
• Ignition switch at ACC
• Selector lever is in position other than “R” with ignition switch ON.
—
Malfunction detected in camera-connection recognition signal
Vehicle Speed Sensor
ON
Vehicle speed is more than 0 km/h with ignition switch ON
OFF
• Ignition switch at ACC
• Vehicle speed is 0 km/h with ignition switch ON
—
Malfunction detected in camera-connection recognition signal
Side view Switch
—
—
JSNIA0085GB
JSNIA0086GB
AV-346
< FUNCTION DIAGNOSIS >
[BOSE AUDIO WITH NAVIGATION]
DIAGNOSIS SYSTEM (AV CONTROL UNIT)
• The device name of Bluetooth can be confirmed and changed.
• The device name can be changed by sixteen digits within A to Z
(small character can be used) and - (hyphen).
SAT
• Change Channel
- Any necessary channels required to receive traffic information from
the satellite radio system can be set.
• Change Application ID
- Any application ID's required to receive traffic information from the
satellite radio system can be set.
Delete Unit Connection Log
Deletes any unit connection records and error records from the AV
control unit memory. (Clear the records of the unit that has been
removed)
Initialize Settings
JSNIA0087GB
JSNIA0092GB
JSNIA0093GB
JSNIA0088GB
AV
DIAGNOSIS SYSTEM (AV CONTROL UNIT)
AV-347
< FUNCTION DIAGNOSIS >
[BOSE AUDIO WITH NAVIGATION]
C
D
E
F
G
H
I
J
K
L
M
B
N
A
O
P
Deletes data stored in HDD.
CONSULT - III Function
INFOID:0000000000964781
CONSULT-III functions
CONSULT-III performs the following functions via the communication with the AV control unit.
Self-diagnosis results
• In CONSULT-III self-diagnosis, self-diagnosis results and error history are displayed collectively.
• The current malfunction indicates “CRNT”. The past malfunction indicates “PAST”.
• The timing is displayed as “0” if any of the error codes [U1000], [U1010], [U1300] and [U1310] is detected.
The counter increases by 1 if the condition is normal at the next ignition switch ON cycle.
Self-diagnosis detection range
Self-diagnosis results display item
JSNIA0095GB
Diagnosis mode
Description
SELF-DIAG RESULTS
Performs a diagnosis on the AV control unit and a connection diagnosis for the communication
circuit of the Multi AV system, and displays the current and past malfunctions collectively.
DATA MONITOR
The diagnosis of vehicle signal that is input to the AV control unit can be performed.
AV COMM MONITOR
Allows the technician to monitor the status of the Multi AV system communication signals.
ECU PART NUMBER
The part number of AV control unit can be checked.
JSNIA0181GB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст