Infiniti G35 (V35) Sedan. Manual — part 954
MWI
B2201 COMMUNICATION ERROR 1
MWI-43
< COMPONENT DIAGNOSIS >
C
D
E
F
G
H
I
J
K
L
M
B
N
A
O
P
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Replace combination meter.
25 - Ground
: Approx. 5 V
MWI-44
< COMPONENT DIAGNOSIS >
B2202 COMMUNICATION ERROR 2
B2202 COMMUNICATION ERROR 2
Description
INFOID:0000000000964381
The communication line (METER <-> AMP.) is used to communicate signals between the combination meter
and the unified meter and A/C amp. in order to control the information display.
DTC Logic
INFOID:0000000000964382
DTC DETECTION LOGIC
Diagnosis Procedure
INFOID:0000000000964383
1.
CHECK CONNECTOR
Check combination meter, unified meter and A/C amp. and terminals (combination meter side, unified meter
and A/C amp. side, and harness side) for looseness or bent.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair terminal or connector.
2.
CHECK CONTINUITY COMMUNICATION CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect combination meter connector and unified meter and A/C amp. connector.
3.
Check continuity between combination meter harness connector M53 terminals 2, 3 and unified meter and
A/C amp. harness connector M66 terminals 27, 7.
4.
Check continuity between combination meter harness connector M53 terminals 2, 3 and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair harness or connector.
3.
CHECK UNIFIED METER AND A/C AMP. OUTPUT VOLTAGE
1.
Turn ignition switch OFF.
2.
Disconnect combination meter connector.
3.
Connect unified meter and A/C amp. connector.
4.
Turn ignition switch ON.
5.
Check voltage between unified meter and A/C amp. harness connector M66 terminal 27 and ground.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Replace unified meter and A/C amp.
4.
CHECK COMBINATION METER OUTPUT VOLTAGE
1.
Turn ignition switch OFF.
2.
Disconnect unified meter and A/C amp. connector.
3.
Connect combination meter connector.
DTC
Display contents of
CONSULT-III
Diagnostic item is detected when ...
Probable malfunction location
B2202
COMM ERROR 2
If a communication error is present in the
communication line (METER <-> AMP.) for 2
seconds or more
Communication line (METER <-> AMP.) circuit
2 - 27
: Continuity should exist.
3 - 7
: Continuity should exist.
2, 3 - Ground
: Continuity should not exist.
27 - Ground
: Approx. 5 V
MWI
B2202 COMMUNICATION ERROR 2
MWI-45
< COMPONENT DIAGNOSIS >
C
D
E
F
G
H
I
J
K
L
M
B
N
A
O
P
4.
Turn ignition switch ON.
5.
Check voltage between combination meter harness connector M53 terminal 3 and ground.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Replace combination meter.
3 - Ground
: Approx. 5 V
MWI-46
< COMPONENT DIAGNOSIS >
B2205 VEHICLE SPEED
B2205 VEHICLE SPEED
Description
INFOID:0000000000964384
Vehicle speed signal is transmitted from ABS actuator and electric unit (control unit) via CAN communication
to unified meter and A/C amp.
DTC Logic
INFOID:0000000000964385
DTC DETECTION LOGIC
Diagnosis Procedure
INFOID:0000000000964386
1.
PERFORM SELF DIAGNOSIS OF ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT)
Perform “Self Diagnosis Result” of ABS actuator and electric unit (control unit), and repair or replace malfunc-
tioning parts.
>> Refer to
BRC-26, "CONSULT-III Function (ABS)"
.
DTC
Display contents of
CONSULT-III
Diagnostic item is detected when ...
Probable malfunction location
B2205
VEHICLE SPEED
If the abnormal vehicle speed signal is input
from ABS actuator and electric unit (control
unit) for 2 seconds or more
ABS actuator and electric unit (control unit)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст