Infiniti G35 (V35) Sedan. Manual — part 686
EXL-186
< ON-VEHICLE REPAIR >
[XENON TYPE]
FRONT COMBINATION LAMP
2.
Rotate the resin cap counterclockwise and unlock it.
3.
Rotate the bulb socket counterclockwise and unlock it.
4.
Remove the retaining spring lock. Remove the bulb from the
headlamp.
CAUTION:
Never break the xenon bulb ceramic tube when replacing
the bulb.
PARKING LAMP BULB
1.
Remove the fender protector. Keep a service area.
2.
Rotate the bulb socket counterclockwise and unlock it.
3.
Remove the bulb from the bulb socket.
FRONT TURN SIGNAL LAMP BULB
1.
Remove the air cleaner case.
2.
Rotate the bulb socket counterclockwise and unlock it.
3.
Remove the bulb from the bulb socket.
FRONT FOG LAMP BULB
1.
Remove the air cleaner case.
2.
Remove the front fog lamp bulb connector.
3.
Rotate the bulb socket counterclockwise and unlock it.
Disassembly and Assembly
INFOID:0000000000962535
DISASSEMBLY
1.
Rotate the resin cap counterclockwise and unlock it.
2.
Rotate the xenon bulb socket counterclockwise and unlock it.
3.
Remove the retaining spring lock. Remove the xenon bulb.
4.
Remove the HID control unit installation screw.
5.
Remove the screw. Disconnect the connector from HID control unit.
6.
Pull out the xenon bulb socket from the headlamp housing assembly.
7.
Rotate the parking lamp bulb socket counterclockwise and unlock it.
8.
Remove the bulb from the parking lamp bulb socket.
9.
Rotate the front turn signal lamp bulb socket counterclockwise and unlock it.
10. Remove the bulb from the front turn signal lamp bulb socket.
11. Rotate the front fog lamp bulb socket counterclockwise. Remove the bulb.
ASSEMBLY
Assemble in the reverse order of disassembly.
CAUTION:
• Install HID control unit securely.
• After installing the bulb, install the resin cap and the bulb socket securely for watertightness.
Adjustment
INFOID:0000000000962536
PREPARATION BEFORE ADJUSTING
NOTE:
• For details, refer to the regulations in your own country.
• Perform aiming if the vehicle front body has been repaired and/or the headlamp assembly has been
replaced.
JPLIA0044ZZ
FRONT COMBINATION LAMP
EXL-187
< ON-VEHICLE REPAIR >
[XENON TYPE]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
Before performing aiming adjustment, check the following.
• Adjust the tire pressure to the specification.
• Fill with gasoline, engine coolant and each oil.
• Maintain the unloaded vehicle condition. (Remove luggage from the passenger compartment and the trunk
room.)
NOTE:
Do not remove the temporary tire, jack and on-vehicle tool.
• Wipe out dirt on the headlamp.
CAUTION:
Never use organic solvent (thinner, gasoline etc.)
• Ride alone on the driver seat.
AIMING ADJUSTMENT SCREW
NOTE:
The figure is the vehicle without AFS. Each adjustment screw is applied to the vehicle with AFS.
JPLIA0041ZZ
A
Headlamp (RH) adjustment screw
B.
Front fog lamp (RH) adjustment
screw
C.
Front fog lamp (LH) adjustment
screw
D.
Headlamp (LH) adjustment screw
: Vehicle center
Adjustment screw
Screw driver rotation
Facing direction
A
Headlamp (RH)
Clockwise
UP
Counterclockwise
DOWN
B
Front fog lamp (RH)
Clockwise
UP
Counterclockwise
DOWN
C
Front fog lamp (LH)
Clockwise
UP
Counterclockwise
DOWN
D
Headlamp (LH)
Clockwise
UP
Counterclockwise
DOWN
EXL-188
< ON-VEHICLE REPAIR >
[XENON TYPE]
FRONT COMBINATION LAMP
AIMING ADJUSTMENT PROCEDURE (HEADLAMP)
1.
Place the screen.
NOTE:
• Stop the vehicle facing the wall.
• Place the board on a plain road vertically.
2.
Face the vehicle with the screen. Maintain 10 m (32.8 ft) between the headlamp center and the screen.
3.
Start the engine. Turn the headlamp (LO) ON.
NOTE:
Shut off the headlamp light with the board to prevent from illuminating the adjustment screen.
CAUTION:
Never cover the lens surface with a tape etc. The lens is made of resin.
4.
Measure the distance (X) between the horizontal center line of headlamp (H) and the cutoff line (A) within
the light axis measurement range (R) from the vertical center line ahead of headlamp (V).
Low beam distribution on the screen
5.
Adjust the cutoff line height (X) with the aiming adjustment screw so as to enter in the adjustment range
(M–N) according to the horizontal center line of headlamp (H).
unit: mm (in)
Side view
AIMING ADJUSTMENT PROCEDURE (FRONT FOG LAMP)
1.
Place the screen.
NOTE:
• Stop the vehicle facing the wall.
• Place the board on a plain road vertically.
Light axis measure-
ment range (R)
: 350
±
175 mm (13.78
±
6.89
in)
JSLIA0005ZZ
Horizontal center line of headlamp (H)
Highest cutoff line height (M)
Lowest cutoff line height (N)
700 (27.56) or less
4 (0.16)
30 (1.18)
701(27.60) – 800 (31.50)
4 (0.16)
30 (1.18)
801 (31.54) or more
17 (0.67)
44 (1.73)
JSLIA0006ZZ
Distance between the
headlamp center and the
screen (L)
: 10 m (32.81 ft)
FRONT COMBINATION LAMP
EXL-189
< ON-VEHICLE REPAIR >
[XENON TYPE]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
2.
Face the vehicle with the screen. Maintain 10 m (32.8 ft) between the front fog lamp center and the
screen.
3.
Start the engine. Turn the front fog lamp ON.
NOTE:
Shut off the headlamp light with the board to prevent from illuminating the adjustment screen.
CAUTION:
Never cover the lens surface with a tape etc. The lens is made of resin.
4.
Adjust the cutoff line height (A) with the aiming adjustment screw so that the distance (X) between the hor-
izontal center line of front fog lamp (H) and (A) becomes 200 mm (7.87 in).
Front fog lamp light distribution on the screen
JPLIA0008ZZ
A
: Cutoff line
B
: High illuminance area
H
: Horizontal center line of front fog lamp
V
: Vertical center line of front fog lamp
X
: Cutoff line height
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст