Infiniti G35 (V35) Sedan. Manual — part 701
FAX-4
< PREPARATION >
[2WD]
PREPARATION
PREPARATION
PREPARATION
Commercial Service Tool
INFOID:0000000000957470
Tool name
Description
Power tool
Looseing bolts and nuts
PBIC0190E
FRONT WHEEL HUB AND KNUCKLE
FAX-5
< ON-VEHICLE MAINTENANCE >
[2WD]
C
E
F
G
H
I
J
K
L
M
A
B
FAX
N
O
P
ON-VEHICLE MAINTENANCE
FRONT WHEEL HUB AND KNUCKLE
Exploded View
INFOID:0000000000957471
.
Inspection
INFOID:0000000000957472
MOUNTING INSPECTION
Make sure that the mounting conditions (looseness, backlash) of each component and component conditions
(wear, damage) are normal.
WHEEL BEARING INSPECTION
• Move wheel hub and bearing assembly in the axial direction by hand. Make sure there is no looseness of
wheel bearing.
• Rotate wheel hub and make sure that is no unusual noise or other irregular conditions. If there is any of
irregular conditions, replace wheel hub and bearing assembly.
Standard
Axial end play
: Refer to
FAX-6
< ON-VEHICLE REPAIR >
[2WD]
FRONT WHEEL HUB AND KNUCKLE
ON-VEHICLE REPAIR
FRONT WHEEL HUB AND KNUCKLE
Exploded View
INFOID:0000000000957473
Removal and Installation
INFOID:0000000000957474
REMOVAL
Wheel Hub and Bearing Assembly
1.
Remove tires from vehicle with power tool.
2.
Remove wheel sensor from steering knuckle. Refer to
BRC-100, "Removal and Installation"
CAUTION:
Never pull on wheel sensor harness.
3.
Remove torque member mounting bolts with power tool. Hang torque member in a place where it will not
interfere with work. Refer to
BR-42, "BRAKE CALIPER ASSEMBLY (1 PISTON TYPE) : Removal and
(1 piston type),
BR-46, "BRAKE CALIPER ASSEMBLY (2 PISTON TYPE) : Removal and
(2 piston type).
CAUTION:
Never depress brake pedal while brake caliper is removed.
4.
Remove disc rotor. Refer to
BR-40, "BRAKE PAD (1 PISTON TYPE) : Inspection and Adjustment"
(1 pis-
ton type),
BR-41, "BRAKE PAD (2 PISTON TYPE) : Inspection and Adjustment"
(2 piston type).
5.
Remove wheel hub and bearing assembly mounting bolts, and then remove splash guard and wheel hub
and bearing assembly from steering knuckle.
Steering Knuckle
1.
Remove wheel hub and bearing assembly, and then remove splash guard.
2.
Remove brake hose bracket. Refer to
BR-21, "FRONT BRAKE : Exploded View"
.
1.
Steering knuckle
2.
Ball seat
3.
Cotter pin
4.
Splash guard
5.
Wheel hub and bearing assembly
Refer to
for symbols in the figure.
JPDIF0001GB
FRONT WHEEL HUB AND KNUCKLE
FAX-7
< ON-VEHICLE REPAIR >
[2WD]
C
E
F
G
H
I
J
K
L
M
A
B
FAX
N
O
P
3.
Remove cotter pin (1) of steering outer socket, and then loosen
the nut.
4.
Remove steering outer socket (2) from steering knuckle (3) so
as not to damage ball joint boot (4) using the ball joint remover.
CAUTION:
Temporarily tighten the nut to prevent damage to threads
and to prevent the ball joint remover from suddenly coming
off.
5.
Remove cotter pin of transverse link and steering knuckle, and
then loosen nut.
6.
Separate upper link from steering knuckle. Refer to
7.
Separate transverse link from steering knuckle so as not to damage ball joint boot using the ball joint
remover.
CAUTION:
Temporarily tighten the nut to prevent damage to threads and to prevent the ball joint remover
from suddenly coming off.
8.
Remove steering knuckle form vehicle.
INSTALLATION
Note the following, and install in the reverse order of the removal.
• Perform the final tightening of each of parts under unladen conditions, which were removed when removing
wheel hub and bearing assembly and steering knuckle.
Inspection
INFOID:0000000000957475
INSPECTION AFTER REMOVAL
Check components for deformation, cracks, and other damage. Replace if there are.
Ball Joint Inspection
Check boots of transverse link and steering outer socket ball joint for breakage, axial play, and torque. Refer to
INSPECTION AFTER INSTALLATION
• Check the wheel alignment. Refer to
• Adjust neutral position of steering angle sensor after checking the wheel alignment. Refer to
"ADJUSTMENT OF STEERING ANGLE SENSOR NEUTRAL POSITION : Special Repair Requirement"
.
SGIA1183E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст