Infiniti G35 (V35) Sedan. Manual — part 245
BRC-54
< COMPONENT DIAGNOSIS >
[VDC/TCS/ABS]
C1130, C1131, C1132 ENGINE SIGNAL
C1130, C1131, C1132 ENGINE SIGNAL
Description
INFOID:0000000000958565
ABS actuator and electric unit (control unit) and ECM exchange the engine signal with CAN communication
line.
DTC Logic
INFOID:0000000000958566
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
CHECK SELF-DIAGNOSIS RESULTS
Check the self-diagnosis results.
Is above displayed on the self-diagnosis display?
YES
>> Proceed to diagnosis procedure. Refer to
.
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000000958567
INSPECTION PROCEDURE
1.
CHECK ENGINE SYSTEM
1.
Perform ECM self-diagnosis. Repair or replace items indicated, then perform ECM self-diagnosis again.
Refer to
EC-113, "CONSULT-III Function"
.
2.
Perform ABS actuator and electric unit (control unit) self-diagnosis. Refer to
.
Is any item indicated on the self-diagnosis display?
YES
>> Repair or replace the affected part.
NO
>> INSPECTION END
Special Repair Requirement
INFOID:0000000000958568
1.
ADJUSTMENT OF STEERING ANGLE SENSOR NEUTRAL POSITION
Always perform the neutral position adjustment for the steering angle sensor, when replacing the ABS actua-
tor and electric unit (control unit). Refer to
BRC-8, "ADJUSTMENT OF STEERING ANGLE SENSOR NEU-
>> END
DTC
Display item
Malfunction detected condition
Possible cause
C1130
ENGINE SIGNAL 1
Major engine components are malfunctioning.
• Harness or connector
• ABS actuator and electric unit
(control unit)
• ECM
• CAN communication line
C1131
ENGINE SIGNAL 2
C1132
ENGINE SIGNAL 3
Self-diagnosis results
ENGINE SIGNAL 1
ENGINE SIGNAL 2
ENGINE SIGNAL 3
C1138 4WAS SYSTEM
BRC-55
< COMPONENT DIAGNOSIS >
[VDC/TCS/ABS]
C
D
E
G
H
I
J
K
L
M
A
B
BRC
N
O
P
C1138 4WAS SYSTEM
Description
INFOID:0000000000958569
The ABS actuator and electric unit (control unit) and the 4WAS control unit exchange signals via the CAN
communication line.
DTC Logic
INFOID:0000000000958570
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
CHECK SELF-DIAGNOSIS RESULTS
Check the self-diagnosis results.
Is above displayed on the self-diagnosis display?
YES
>> Proceed to diagnosis procedure. Refer to
.
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000000958571
INSPECTION PROCEDURE
1.
CHECK 4WAS SYSTEM
1.
Perform 4WAS self-diagnosis. Repair or replace items indicated, then perform 4WAS self-diagnosis
again. Refer to
STC-39, "CONSULT-III Function [4WAS(FRONT)]"
(4WAS FRONT CONTROL UNIT),
STC-43, "CONSULT-III Function [4WAS(MAIN)/RAS/HICAS]"
(4WAS MAIN CONTROL UNIT).
2.
Perform ABS actuator and electric unit (control unit) self-diagnosis. Refer to
.
Is any item indicated on the self-diagnosis display?
YES
>> Repair or replace the affected part.
NO
>> INSPECTION END
Special Repair Requirement
INFOID:0000000000958572
1.
ADJUSTMENT OF STEERING ANGLE SENSOR NEUTRAL POSITION
Always perform the neutral position adjustment for the steering angle sensor, when replacing the ABS actua-
tor and electric unit (control unit). Refer to
BRC-8, "ADJUSTMENT OF STEERING ANGLE SENSOR NEU-
>> END
DTC
Display item
Malfunction detected condition
Possible cause
C1138
4WAS CIRCUIT
Abnormal condition in major 4WAS parts.
• ABS actuator and electric unit
(control unit)
• 4WAS system
• CAN communication line
Self-diagnosis results
4WAS CIRCUIT
BRC-56
< COMPONENT DIAGNOSIS >
[VDC/TCS/ABS]
C1142 PRESS SENSOR
C1142 PRESS SENSOR
Description
INFOID:0000000000958573
The pressure sensor converts the brake fluid pressure to an electric signal and transmits it to the ABS actuator
and electric unit (control unit). [The pressure sensor is integrated in the ABS actuator and electric unit (control
unit).]
DTC Logic
INFOID:0000000000958574
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
CHECK SELF-DIAGNOSIS RESULTS
Check the self-diagnosis results.
Is above displayed on the self-diagnosis display?
YES
>> Proceed to diagnosis procedure. Refer to
.
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000000958575
INSPECTION PROCEDURE
1.
CHECK STOP LAMP SWITCH CONNECTOR
1.
Turn ignition switch OFF.
2.
Disconnect ABS actuator and electric unit (control unit) connector.
3.
Disconnect stop lamp switch connector.
4.
Check terminal for deformation, disconnection, looseness, and so on. If any malfunction is found, repair or
replace terminal.
5.
Reconnect connectors securely.
6.
Start engine.
7.
Repeat pumping brake pedal carefully several times, and perform self-diagnosis.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Poor connection of connector terminal. Repair or replace connector.
2.
CHECK STOP LAMP SWITCH
1.
Turn ignition switch OFF.
2.
Disconnect stop lamp switch connector.
3.
Check continuity between stop lamp switch connector terminals.
DTC
Display item
Malfunction detected condition
Possible cause
C1142
PRESS SEN CIRCUIT
Pressure sensor signal line is open or shorted, or pres-
sure sensor is malfunctioning.
• Harness or connector
• Stop lamp switch
• ABS actuator and electric unit
(control unit)
Self-diagnosis results
PRESS SEN CIRCUIT
Stop lamp switch
Condition
Continuity
Connector
Terminal
E110
3
−
4
Release stop lamp switch
(When brake pedal is depressed.)
Existed
Push stop lamp switch
(When brake pedal is released.)
Not existed
C1142 PRESS SENSOR
BRC-57
< COMPONENT DIAGNOSIS >
[VDC/TCS/ABS]
C
D
E
G
H
I
J
K
L
M
A
B
BRC
N
O
P
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Replace stop lamp switch.
3.
CHECK STOP LAMP SWITCH CIRCUIT
1.
Disconnect ABS actuator and electric unit (control unit) connector.
2.
Connect stop lamp switch connector.
3.
Check voltage between ABS actuator and electric unit (control unit) harness connector terminal and
ground.
Is the inspection result normal?
YES
>> Replace ABS actuator and electric unit (control unit).
NO
>> Repair or replace malfunctioning components.
Component Inspection
INFOID:0000000000958576
1.
CHECK DATA MONITOR
On “DATA MONITOR”, select “PRESS SENSOR” and check the brake fluid pressure.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Go to diagnosis procedure. Refer to
Special Repair Requirement
INFOID:0000000000958577
1.
ADJUSTMENT OF STEERING ANGLE SENSOR NEUTRAL POSITION
Always perform the neutral position adjustment for the steering angle sensor, when replacing the ABS actua-
tor and electric unit (control unit). Refer to
BRC-8, "ADJUSTMENT OF STEERING ANGLE SENSOR NEU-
>> END
ABS actuator and electric unit (control unit)
Condition
Voltage
Connector
Terminal
E41
30
Brake pedal is depressed
Battery voltage
Brake pedal is released
Approx. 0 V
Condition
PRESS SENSOR
(DATA MONITOR)
With ignition switch turned ON and brake pedal released.
Approx. 0 bar
With ignition switch turned ON and brake pedal depressed.
−
40 to 300 bar
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст