Infiniti G35 (V35) Sedan. Manual — part 694
EXT-14
< ON-VEHICLE REPAIR >
REAR BUMPER
Removal and Installation
INFOID:0000000000961797
REMOVAL
CAUTION:
Bumper fascia is made of resin. Do not apply strong force to it, and be careful to prevent contact with
oil.
1.
Fully open trunk lid assembly.
2.
Remove rear combination lamp (LH/RH). Refer to
EXL-198, "Removal and Installation"
3.
Remove clips (A) located under rear combination lamp (LH/RH).
4.
Remove screw (A) of bumper fascia underside.
5.
Remove clips (B) of rear wheel house protector rear end (LH/
RH).
6.
Remove screws (A) of bumper fascia front end upper (LH/RH).
7.
Remove clips of bumper fascia underside, and then pull out bumper fascia toward rear of vehicle.
8.
Disconnect license plate lamp connector (A).
9.
Remove bumper fascia assembly.
JMKIA0093GB
JMKIA0094GB
JMKIA0095GB
JMKIA0096GB
REAR BUMPER
EXT-15
< ON-VEHICLE REPAIR >
C
D
E
F
G
H
I
J
L
M
A
B
EXT
N
O
P
CAUTION:
When removing bumper fascia, 2 workers are required so as to prevent it from dropping.
10. Remove the following parts after removing bumper fascia.
• License lamp. Refer to
EXL-202, "Removal and Installation"
• License lamp bracket.
• License plate bracket.
• Bumper clip.
11. Remove bumper energy absorber.
12. Remove license lamp harness clamps of bumper reinforcement.
13. Remove bumper reinforcement mounting nuts and bolts, and then remove bumper reinforcement with
power tool.
INSTALLATION
Install in the reverse order of removal.
NOTE:
After installing, perform fitting adjustment.
Portion
Clearance
Rear bumper – Trunk lid
A – A
4.0 – 8.0 mm (0.157 – 0.315 in)
Rear bumper – Rear combination lamp
B – B
0.0 – 3.0 mm (0.000 – 0.118 in)
Rear bumper – Rear fender
C – C
0.0 – 0.8 mm (0.000 – 0.031 in)
Rear bumper – Rear fender
D – D
0.0 – 0.8 mm (0.000 – 0.031 in)
EXT-16
< ON-VEHICLE REPAIR >
FRONT GRILLE
FRONT GRILLE
Exploded View
INFOID:0000000000961798
Removal and Installation
INFOID:0000000000961799
REMOVAL
CAUTION:
Apply protection tape around outer circumference of front grille (bumper fascia side).
1.
Fully open hood assembly.
2.
Remove reservoir tank. Refer to
CO-14, "Removal and Installation"
.
3.
Remove radiator core support ornament. Refer to
DLK-196, "Removal and Installation"
4.
Remove front grille mounting nuts (A).
1.
Front grille
2.
Front emblem
Pawl
JMKIA0076GB
JMKIA0097GB
FRONT GRILLE
EXT-17
< ON-VEHICLE REPAIR >
C
D
E
F
G
H
I
J
L
M
A
B
EXT
N
O
P
5.
Disengage pawls (A) of fixing front grille.
6.
Pull front grille out toward vehicle front.
7.
Remove the following parts after removing front grille.
Front emblem
INSTALLATION
Install in the reverse order of removal.
: Pawl
JMKIA0098GB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст