Infiniti G35 (V35) Sedan. Manual — part 348
DIAGNOSIS SYSTEM (BCM)
DLK-53
< FUNCTION DIAGNOSIS >
[INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
ACTIVE TEST
Monitor Item
Condition
REQ SW-DR
Indicates [ON/OFF] condition of door request switch (driver side).
REQ SW-AS
Indicates [ON/OFF] condition of door request switch (passenger side).
REQ SW-BD/TR
Indicates [ON/OFF] condition of trunk opener request switch.
PUSH SW
Indicates [ON/OFF] condition of push-button ignition switch.
CLUCH SW
Indicates [ON/OFF] condition of clutch switch.
BRAKE SW 1
Indicates [ON/OFF] condition of brake switch.
DETE/CANCL SW
Indicates [ON/OFF] condition of P position.
SFT PN/N SW
Indicates [ON/OFF] condition of P or N position.
S/L -LOCK
Indicates [ON/OFF] condition of steering lock (LOCK).
S/L -UNLOCK
Indicates [ON/OFF] condition of steering lock (UNLOCK).
S/L RELAY-F/B
Indicates [ON/OFF] condition of ignition switch.
UNLK SEN-DR
Indicates [ON/OFF] condition of driver door UNLOCK status.
PUSH SW -IPDM
Indicates [ON/OFF] condition of push-button ignition switch.
IGN RLY1 F/B
Indicates [ON/OFF] condition of ignition relay 1.
DETE SW -IPDM
Indicates [ON/OFF] condition of P position.
SFT PN -IPDM
Indicates [ON/OFF] condition of P or N position.
SFT P -MET
Indicates [ON/OFF] condition of P position.
SFT N -MET
Indicates [ON/OFF] condition of N position.
ENGINE STATE
Indicates [STOP/START/CRANK/RUN] condition of engine states.
S/L LOCK-IPDM
Indicates [ON/OFF] condition of steering lock (LOCK).
S/L UNLOCK-IPDM
Indicates [ON/OFF] condition of steering lock (UNLOCK).
S/L RELAY-REQ
Indicates [ON/OFF] condition of steering lock relay.
VEH SPEED 1
Display the vehicle speed signal received from combination meter by numerical value [Km/h].
VEH SPEED 2
Display the vehicle speed signal received from ABS or VDC or CVT by numerical value [Km/h].
DOOR STAT-DR
Indicates [LOCK/READY/UNLK] condition of driver side door status.
DOOR STAT-AS
Indicates [LOCK/READY/UNLK] condition of passenger side door status.
KEY SW -SLOT
Indicates [ON/OFF] condition of key slot.
RKE OPE COUN1
When remote keyless entry receiver receives the signal transmitted while operating on Intelligent Key, the
numerical value start changing.
RKE OPE COUN2
NOTE:
This item is displayed, but cannot be monitored.
TRNK/HAT MNTR
Indicates [ON/OFF] condition of trunk lid.
RKE-LOCK
Indicates [ON/OFF] condition of LOCK signal from Intelligent Key.
RKE-UNLOCK
Indicates [ON/OFF] condition of UNLOCK signal from Intelligent Key.
RKE-TR/BD
Indicates [ON/OFF] condition of TRUNK OPEN signal from Intelligent Key.
RKE-PANIC
Indicates [ON/OFF] condition of PANIC button of Intelligent Key.
RKE-P/W OPEN
Indicates [ON/OFF] condition of P/W DOWN signal from Intelligent Key.
RKE-MODE CHG
Indicates [ON/OFF] condition of MODE CHANGE signal from Intelligent Key.
Test item
Description
BATTERY SAVER
This test is able to check interior room lamp operation.
The interior room lamp will be activated after “ON” on CONSULT-III screen is touched.
PW REMOTO DOWN SET
This test is able to check power window down operation.
The power window down will be activated after “ON” on CONSULT-III screen is touched.
DLK-54
< FUNCTION DIAGNOSIS >
[INTELLIGENT KEY SYSTEM]
DIAGNOSIS SYSTEM (BCM)
TRUNK
TRUNK : CONSULT-III Function (BCM - TRUNK)
INFOID:0000000000961119
BCM CONSULT-III FUNCTION
CONSULT-III performs the following functions via CAN communication with BCM.
OUTSIDE BUZZER
This test is able to check Intelligent Key warning buzzer operation.
Intelligent Key warning buzzer sounds when “ON” on CONSULT-III screen is touched.
INSIDE BUZZER
This test is able to check warning chime in combination meter operation.
• Take away warning chime sounds when “TAKE OUT” on CONSULT-III screen is touched.
• Key warning chime sounds when “KEY WARN” on CONSULT-III screen is touched.
• P position warning chime sounds when “P RNG WARN” on CONSULT-III screen is touched.
• ACC warning chime sounds when “ACC WARN” on CONSULT-III screen is touched.
INDICATOR
This test is able to check warning lamp operation.
• “KEY” Warning lamp illuminates when “KEY IND ON” on CONSULT-III screen is touched.
• “KEY” Warning lamp flashes when “KEY IND FSH” on CONSULT-III screen is touched.
INT LAMP
This test is able to check interior room lamp operation.
The interior room lamp will be activated after “ON” on CONSULT-III screen is touched.
LCD
This test is able to check meter display information
• Engine start information displays when “BRAKE/P” on CONSULT-III screen is touched.
• Engine start information displays when “BRAKE/P/ON” on CONSULT-III screen is touched.
• Key ID warning displays when “KEY ID NG” on CONSULT-III screen is touched.
• Steering lock information displays when “STLCK RELES” on CONSULT-III screen is touched.
• P position warning displays when “P RNG IND” on CONSULT-III screen is touched.
• Intelligent Key insert information displays when “INSERT KEY” on CONSULT-III screen is
touched.
• Intelligent Key low battery warning displays when “KEY BAT LOW” on CONSULT-III screen is
touched.
• Take away through window warning displays when “TK AWAY WDW” on CONSULT-III screen
is touched.
• Take away warning display when “TAKE AWAY” on CONSULT-III screen is touched.
• OFF position warning display when “IGN OFF WARN” on CONSULT-III screen is touched.
TRUNK/GLASS HATCH
This test is able to check trunk lid opener actuator open operation.
This actuator opens when “ON” on CONSULT-III screen is touched.
FLASHER
This test is able to check security hazard lamp operation.
The hazard lamps will be activated after “ON” on CONSULT-III screen is touched.
HORN
This test is able to check horn operation.
The horn will be activated after “ON” on CONSULT-III screen is touched.
IGN CONT2
This test is able to check security hazard lamp operation.
The hazard lamps will be activated after “ON” on CONSULT-III screen is touched.
P RANGE
This test is able to check A/T device power supply
A/T device power is supplied when “ON” on CONSULT-III screen is touched.
ENGINE SW ILLUMI
This test is able to check push-ignition switch illumination operation.
Push-ignition switch illumination illuminates when “ON” on CONSULT-III screen is touched.
LOCK INDCATOR
This test is able to check LOCK indicator in push-ignition switch operation.
LOCK indicator in push-ignition switch illuminates when “ON” on CONSULT-III screen is touched.
ACC INDCATOR
This test is able to check ACC indicator in push-ignition switch operation.
LOCK indicator in push-ignition switch illuminates when “ON” on CONSULT-III screen is touched.
IGNITION ON IND
This test is able to check INGITION ON indicator in push-ignition switch operation.
LOCK indicator in push-ignition switch illuminates when “ON” on CONSULT-III screen is touched.
KEY SLOT ILLUMI
This test is able to check key slot illumination operation.
Key slot illumination flash when “ON” on CONSULT-III screen is touched.
Test item
Description
Diagnosis mode
Function Description
DATA MONITOR
The BCM input/output signals are displayed.
ACTIVE TEST
The signals used to activate each device are forcibly supplied from BCM.
DIAGNOSIS SYSTEM (BCM)
DLK-55
< FUNCTION DIAGNOSIS >
[INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
DATA MONITOR
ACTIVE TEST
Monitor Item
Contents
PUSH SW
Indicates [ON/OFF] condition of push switch.
UNLK SEN -DR
Indicates [ON/OFF] condition of unlock sensor.
VEH SPEED 1
Indicates [Km/h] condition of vehicle speed signal from combination meter.
KEY CYL SW-TR
NOTE:
This item is displayed, but cannot be monitored.
TR CANCEL SW
Indicates [ON/OFF] condition of trunk lid opener cancel switch.
TR/BD OPEN SW
Indicates [ON/OFF] condition of trunk lid opener switch.
TRNK/HAT MNTR
Indicates [ON/OFF] condition of trunk room lamp switch.
RKE-TR/BD
Indicates [ON/OFF] condition of trunk open signal from Intelligent Key remote controller button.
Test item
Description
TRUNK/GLASS HATCH
This test is able to check trunk open operation.
Trunk open when “OPEN” on CONSULT-III screen is touched.
DLK-56
< COMPONENT DIAGNOSIS >
[INTELLIGENT KEY SYSTEM]
U1000 CAN COMM CIRCUIT
COMPONENT DIAGNOSIS
U1000 CAN COMM CIRCUIT
Description
INFOID:0000000000961120
CAN (Controller Area Network) is a serial communication line for real time applications. It is an on-vehicle mul-
tiplex communication line with high data communication speed and excellent error detection ability. Modern
vehicle is equipped with many electronic control unit, and each control unit shares information and links with
other control units during operation (not independent). In CAN communication, control units are connected
with 2 communication lines (CAN H-line, CAN L-line) allowing a high rate of information transmission with less
wiring. Each control unit transmits/receives data but selectively reads required data only.
CAN Communication Signal Chart. Refer to
LAN-28, "CAN Communication Signal Chart"
DTC Logic
INFOID:0000000000961121
DTC DETECTION LOGIC
Diagnosis Procedure
INFOID:0000000000961122
1.
PERFORM SELF DIAGNOSTIC
1.
Turn ignition switch ON and wait for 2 second or more.
2.
Check “Self Diagnostic Result”.
Is “CAN COMM CIRCUIT” displayed?
YES
>> Refer to
LAN-18, "Trouble Diagnosis Flow Chart"
NO
>> Refer to
GI-39, "Intermittent Incident"
.
DTC
CONSULT-III display
description
DTC Detection Condition
Possible cause
U1000
CAN COMM CIRCUIT
When BCM cannot communicate CAN com-
munication signal continuously for 2 sec-
onds or more.
In CAN communication system, any item (or items)
of the following listed below is malfunctioning.
• Transmission
• Receiving (ECM)
• Receiving (VDC/TCS/ABS)
• Receiving (METER/M&A)
• Receiving (TCM)
• Receiving (MULTI AV)
• Receiving (IPDM E/R)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст