Infiniti G35 (V35) Sedan. Manual — part 829
IP-12
< ON-VEHICLE REPAIR >
INSTRUMENT PANEL ASSEMBLY
Removal and Installation
INFOID:0000000000960455
REMOVAL
1.
Put selector lever in drive position. (A/T Models only)
2.
Remove selector lever knob. (A/T Models only)
• Refer to
TM-232, "2WD : Removal and Installation"
. (2WD models)
• Refer to
TM-234, "AWD : Removal and Installation"
. (AWD models)
3.
Remove shift lever knob. (M/T Models only) Refer to
TM-18, "Removal and Installation"
.
4.
Remove console finisher.
• Remove clips from rear of console finisher, and then remove pawl of front. Pull console finisher upward
to disengage from center console.
• Disconnect harness connectors.
5.
Remove screws (B) of center console front side with screw
driver (A).
1.
Instrument finisher A
2.
Cluster lid A assembly
3.
Steering column cover upper
4.
Steering column cover lower
5.
Steering column side cover (LH)
6.
Steering column side cover (RH)
7.
Steering column mask
8.
Cluster lid A lower bracket
9.
Steering column front lower cover
10. Meter bracket
11.
Knee protector lower
12. Instrument driver lower panel
13. Cluster lid C assembly
14. AV control unit
15. Cluster lid D assembly
16. Center ventilator grille (LH)
17. Center ventilator grille (RH)
18. Glove box assembly
19. Glove box lock assembly
20. Instrument finisher B
21. Instrument lower cover
22. Instrument assist lower panel
23. Instrument side panel (LH)
24. Instrument side panel (RH)
25. Instrument side finisher (RH)
26. Instrument side finisher (LH)
27. Instrument panel & pad
28. Center speaker grille
Clip
Pawl
Metal clip
1.
Console finisher (AT models)
2.
Console finisher (MT models)
: Pawl
: Metal clip
JMJIA0031GB
JMJIA0032GB
INSTRUMENT PANEL ASSEMBLY
IP-13
< ON-VEHICLE REPAIR >
C
D
E
F
G
H
I
K
L
M
A
B
IP
N
O
P
6.
Remove rear upper console assembly. (AT Models only)
• Slide to front, pull up rear upper console assembly (1), and
disconnect metal clips.
• Disconnect heated seat switch harness connectors. (with
heated seat)
7.
Disconnect auxiliary input jacks connector (A) and power socket
harness connector (B). (AT Models only)
8.
Disconnect console sub harness connectors (A). (MT Models
only)
9.
Disconnect heated seat switch connector (A). (MT models with
heated seat only)
10. Remove coin pocket fixing pawl using a remover tool (A), and
then remove coin pocket (1). (MT Models only)
: Pawl
: Metal clip
JMJIA0033GB
JMJIA0065ZZ
JMJIA0038GB
JMJIA0286ZZ
: Pawl
JMJIA0034GB
IP-14
< ON-VEHICLE REPAIR >
INSTRUMENT PANEL ASSEMBLY
11. Insert a deep-well socket wrench (A) to rotate adjusting nut to
loosen cable sufficiently. (MT Models only) Refer to
"LEVER TYPE : Inspection and Adjustment"
.
12. Remove console rear finisher.
• Pull back the console rear finisher (1).
• Disconnect inside key antenna connector (A).
13. Remove console mask.
• Open the console lid.
• Pull up console mask (1) by using a remover tool (C), and disengage pawls.
14. Remove screws (C) of center console rear side, and then remove center console assembly (1).
JMJIA0035GB
: Metal clip
JMJIA0037GB
(A)
Console mask (with rear ventilator grille)
(B)
Console mask (without rear ventilator grille)
: Pawl
JMJIA0036GB
(A)
Console mounting screws
(with rear ventilator grille)
(B)
Console mounting screws
(without rear ventilator grille)
JMJIA0039GB
INSTRUMENT PANEL ASSEMBLY
IP-15
< ON-VEHICLE REPAIR >
C
D
E
F
G
H
I
K
L
M
A
B
IP
N
O
P
15. Remove cluster lid C.
• Remove cluster lid C mounting screws (A).
• Pull back cluster lid C (1).
• Disconnect harness connectors.
16. Remove cluster lid D.
• Remove cluster lid D mounting screw (A).
• Pull back cluster lid D (1).
• Disconnect harness connectors.
17. Remove display unit. Refer to
AV-531, "Removal and Installation"
.
18. Disconnect center speaker harness connector (A). (with center
speaker)
19. Remove screw (B).
20. Disconnect inside key antenna connector (A) and clip (B)
located under audio unit.
21. Remove AV control unit. Refer to
AV-111, "Removal and Installation"
.
22. Remove front body side welt LH. Refer to
INT-13, "Removal and Installation"
.
23. Remove front pillar garnish LH. Refer to
INT-13, "Removal and Installation"
JMJIA0043GB
: Pawl
JMJIA0044GB
JMJIA0045GB
JMJIA0046GB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст