Infiniti G35 (V35) Sedan. Manual — part 30
ADP-114
< COMPONENT DIAGNOSIS >
TELESCOPIC SENSOR
TELESCOPIC SENSOR
Description
INFOID:0000000000960720
• The telescopic sensor is installed to the steering column assembly.
• The resistance of telescopic sensor is changed according to the forward/backward position of steering col-
umn.
• The terminal voltage of automatic drive positioner control unit will be changed according to a change of tele-
scopic sensor resistance. Automatic drive positioner control unit calculates the telescopic position from the
voltage.
Component Function Check
INFOID:0000000000960721
1.
CHECK FUNCTION
1.
Select “TELESCO SEN” in “Data monitor” mode with CONSULT-III.
2.
Check the tilt sensor signal under the following conditions.
Is the indication normal?
YES
>> INSPECTION END.
NO
>> Perform diagnosis procedure. Refer to
ADP-114, "Diagnosis Procedure"
.
Diagnosis Procedure
INFOID:0000000000960722
1.
CHECK TELESCOPIC SENSOR SIGNAL
1.
Turn ignition switch ON.
2.
Check voltage automatic drive positioner control unit harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 7.
NO
>> GO TO 2.
2.
CHECK TELESCOPIC SENSOR CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect automatic drive positioner control unit and tilt & telescopic sensor connector.
3.
Check continuity between automatic drive positioner control unit harness connector and tilt & telescopic
sensor harness connector.
4.
Check continuity between automatic drive positioner control unit harness connector and ground.
Is the inspection result normal?
Monitor item
Condition
Value
TELESCO SEN
Telescopic position
Rear
0.8 [V]
Front
3.4 [V]
Terminal
Condition
Voltage (V)
(Approx.)
(+)
(-)
Tilt & telescopic
sensor connector
Terminal
M48
2
Ground
Telescopic position
Rear
0.8 [V]
Front
3.4 [V]
Automatic drive positioner
control unit connector
Terminal
Tilt & telescopic sensor
connector
Terminal
Continuity
M51
23
M48
2
Existed
Automatic drive positioner
control unit connector
Terminal
Ground
Continuity
M51
23
Not existed
TELESCOPIC SENSOR
ADP-115
< COMPONENT DIAGNOSIS >
C
D
E
F
G
H
I
K
L
M
A
B
ADP
N
O
P
YES
>> GO TO 3.
NO
>> Repair or replace harness.
3.
CHECK TELESCOPIC SENSOR POWER SUPPLY
1.
Connect automatic drive positioner control unit connector.
2.
Turn ignition switch ON.
3.
Check voltage between tilt & telescopic sensor harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> GO TO 4.
4.
CHECK TELESCOPIC SENSOR POWER SUPPLY CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect automatic drive positioner control unit connector.
3.
Check continuity between automatic drive positioner control unit harness connector and tilt & telescopic
sensor harness connector.
4.
Check continuity between automatic drive positioner control unit harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 6.
NO
>> Repair or replace harness.
5.
CHECK TELESCOPIC SENSOR GROUND CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect automatic drive positioner control unit connector.
3.
Check continuity between automatic drive positioner control unit harness connector and tilt & telescopic
sensor harness connector.
Is the inspection result normal?
YES
>> GO TO 6.
NO
>> Repair or replace harness.
6.
CHECK DOOR MIRROR OPERATION
1.
Connect automatic drive positioner control unit connector and tilt & telescopic sensor connector.
2.
Turn ignition switch ON.
3.
Check door mirror operation with memory function.
Is the operation normal?
YES
>> Replace telescopic sensor. (Built in steering column assembly.)
NO
>> Repair or replace harness.
7.
CHECK INTERMITTENT INCIDENT
Terminal
Voltage (V)
(Approx.)
(+)
(–)
Tilt & telescopic sensor
Terminal
M48
2
Ground
5
Automatic drive positioner
control unit connector
Terminal
Tilt & telescopic sensor
connector
Terminal
Continuity
M52
33
M48
1
Existed
Automatic drive positioner
control unit connector
Terminal
Ground
Continuity
M52
33
Not existed
Automatic drive positioner
control unit connector
Terminal
Tilt & telescopic sensor
connector
Terminal
Continuity
M52
41
M48
4
Existed
ADP-116
< COMPONENT DIAGNOSIS >
TELESCOPIC SENSOR
GI-39, "Intermittent Incident"
Is the inspection result normal?
YES
>> Replace automatic drive positioner control unit.
NO
>> Repair or replace the malfunctioning part.
MIRROR SENSOR
ADP-117
< COMPONENT DIAGNOSIS >
C
D
E
F
G
H
I
K
L
M
A
B
ADP
N
O
P
MIRROR SENSOR
DRIVER SIDE
DRIVER SIDE : Description
INFOID:0000000000960723
• The mirror sensor (driver side) is installed to the door mirror (driver side).
• The resistance of 2 sensors (horizontal and vertical) is changed when the door mirror (driver side) is oper-
ated.
• Automatic drive positioner control unit calculates the door mirror position according to the change of the volt-
age of 2 sensor input terminals.
DRIVER SIDE : Component Function Check
INFOID:0000000000960724
1.
CHECK FUNCTION
1.
Select “MIR/SEN LH U-D”, “MIR/SEN LH R-L” in “Data monitor” with CONSULT-III.
2.
Check mirror sensor (driver side) signal under the following condition.
Is the indication normal?
YES
>> INSPECTION END
NO
>> Perform diagnosis procedure. Refer to
ADP-117, "DRIVER SIDE : Diagnosis Procedure"
DRIVER SIDE : Diagnosis Procedure
INFOID:0000000000960725
1.
CHECK DOOR MIRROR (DRIVER SIDE) SENSOR SIGNAL
1.
Turn ignition switch ON.
2.
Check voltage between door mirror (driver side) harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 7.
NO
>> GO TO 2.
2.
CHECK DOOR MIRROR (DRIVER SIDE) SENSOR CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect automatic drive positioner control unit and door mirror (driver side) connector.
3.
Check continuity between automatic drive positioner control unit harness connector and door mirror
(driver side) harness connector.
Monitor item
Condition
Value
MIR/SEN LH U-D
Door mirror (driver side)
Close to peak
3.4 [V]
Close to valley
0.6 [V]
MIR/SEN LH R-L
Close to right edge
3.4 [V]
Close to left edge
0.6 [V]
Terminals
Condition
Voltage (V)
(Approx.)
(+)
(–)
Door mirror (driver
side) connector
Terminal
D3
9
Ground
Door mirror
(Driver side)
Close to peak
3.4
Close to valley
0.6
10
Close to right edge
3.4
Close to left edge
0.6
Automatic drive positioner
control unit connector
Terminal
Door mirror (driver side)
connector
Terminal
Continuity
M51
6
D3
9
Existed
22
10
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст