Infiniti G35 (V35) Sedan. Manual — part 1281
STC-14
< COMPONENT DIAGNOSIS >
[WITHOUT 4WAS]
ENGINE SPEED SIGNAL CIRCUIT
NO
>> Replace ECM. Refer to
EC-15, "ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT :
.
4.
CHECK ENGINE SPEED SIGNAL (2)
1.
Turn the ignition switch OFF.
2.
Connect power steering control unit harness connector.
3.
Check signal between power steering control unit harness connector and ground with oscilloscope.
Also check harness for short to ground and short to power.
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> Replace power steering control unit. Refer to
5.
CHECK TERMINALS AND HARNESS CONNECTORS
• Check power steering control unit pin terminals for damage or loose connection with harness connector.
• Check ECM pin terminals for damage or loose connection with harness connector.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Repair or replace damaged parts.
Power steering control unit
Value (Approx.)
Connector
Terminal
Condition
M108
10 – Ground
Engine speed: At idle
(Warm-up condition)
Engine speed: Approx. 2,000 rpm
(Warm-up condition)
PBIA3654J
PBIA3655J
VEHICLE SPEED SIGNAL CIRCUIT
STC-15
< COMPONENT DIAGNOSIS >
[WITHOUT 4WAS]
C
D
E
F
H
I
J
K
L
M
A
B
STC
N
O
P
VEHICLE SPEED SIGNAL CIRCUIT
Description
INFOID:0000000000958716
• Unified meter and A/C amp. sends vehicle speed signal to power steering control unit.
Diagnosis Procedure
INFOID:0000000000958717
1.
PERFORM UNIFIED METER AND A/C AMP. SELF-DIAGNOSIS
With CONSULT-III
Perform unified meter and A/C amp. self-diagnosis.
Is any error system detected?
YES
>> Check the error system.
NO
>> GO TO 2.
2.
CHECK HARNESS BETWEEN UNIFIED METER AND A/C AMP. AND POWER STEERING CONTROL
UNIT
1.
Turn the ignition switch OFF.
2.
Disconnect unified meter and A/C amp. harness connector.
3.
Disconnect power steering control unit harness connector.
4.
Check continuity between unified meter and A/C amp. harness connector and power steering control unit
harness connector.
Also check harness for short to ground and short to power.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace damaged parts.
3.
CHECK VEHICLE SPEED SIGNAL (1)
1.
Turn the ignition switch OFF.
2.
Connect unified meter and A/C amp. harness connector.
3.
Check unified meter and A/C amp. input/output standard values. Refer to
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Replace unified meter and A/C amp. Refer to
4.
CHECK VEHICLE SPEED SIGNAL (2)
1.
Turn the ignition switch OFF.
2.
Connect power steering control unit harness connector.
3.
Check signal between power steering control unit harness connector and ground with oscilloscope.
Also check harness for short to ground and short to power.
Unified meter and A/C amp.
Power steering control unit
Continuity
Connector
Terminal
Connector
Terminal
M66
8
M108
8
Existed
Power steering control unit
Value (Approx.)
Connector
Terminal
Condition
M108
8 – Ground
Vehicle speed:
40 km/h (25 MPH)
CAUTION:
Check air pressure of tire under
standard condition.
SEIA0775E
STC-16
< COMPONENT DIAGNOSIS >
[WITHOUT 4WAS]
VEHICLE SPEED SIGNAL CIRCUIT
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> Replace power steering control unit. Refer to
5.
CHECK TERMINALS AND HARNESS CONNECTORS
• Check power steering control unit pin terminals for damage or loose connection with harness connector.
• Check unified meter and A/C amp. pin terminals for damage or loose connection with harness connector.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Repair or replace damaged parts.
POWER STEERING CONTROL UNIT
STC-17
< ECU DIAGNOSIS >
[WITHOUT 4WAS]
C
D
E
F
H
I
J
K
L
M
A
B
STC
N
O
P
ECU DIAGNOSIS
POWER STEERING CONTROL UNIT
Reference Value
INFOID:0000000000958718
TERMINAL LAYOUT
PHYSICAL VALUES
CAUTION:
JSGIA0023ZZ
Terminal No.
Wire
color
Description
Condition
Value (Approx.)
+
-
Signal name
Input/
Output
1
Ground
LG
Power steering so-
lenoid valve voltage
Output
Vehicle speed: 0 km/h (0 MPH)
(Engine is running)
4.4 – 6.6 V
Vehicle speed: 100 km/h (62 MPH)
2.4 – 3.6 V
3
Ground
G
Ignition switch pow-
er supply
Input
Ignition switch: ON
Battery voltage
Ignition switch: OFF
0 V
5
Ground
B
Power steering so-
lenoid valve ground
—
Always
0 V
6
Ground
B
Ground
—
Always
0 V
8
Ground
L
Vehicle speed sig-
nal
Input
Vehicle speed: 40 km/h (25 MPH)
CAUTION:
Check air pressure of tire under
standard condition.
10
Ground
R
Engine speed signal
Input
Engine speed: At idle
(Warm-up condition)
Engine speed: Approx. 2,000 rpm
(Warm-up condition)
SEIA0775E
PBIA3654J
PBIA3655J
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст