Infiniti G35 (V35) Sedan. Manual — part 4
ADP-10
< BASIC INSPECTION >
INSPECTION AND ADJUSTMENT
MEMORY STORING : Description
INFOID:0000000000960583
Always perform the memory storage when the battery terminal is disconnected or the driver seat control unit is
replaced. The memory function and Intelligent Key interlock function will not operate normally if no memory
storage is performed.
MEMORY STORING : Special Repair Requirement
INFOID:0000000000960584
Memory Storage Procedure
Two positions for the driver seat, steering column and outside mirror can be stored for memory operation by
following procedure.
1.
STEP 1
Shift AT selector lever to P position (AT model) or applied parking brake (MT model).
>> GO TO 2.
2.
STEP 2
Turn ignition switch ON.
>> GO TO 3.
3.
STEP 3
Adjust driver seat, steering column and outside mirror position manually.
>> GO TO 4.
4.
STEP 4
1.
Push set switch.
NOTE:
• Memory indicator for which driver seat position is already retained in memory is illuminated for 5 sec-
onds.
• Memory indicator for which driver seat position is not retained in memory is illuminated for 0.5 second.
2.
Push the memory switch (1 or 2) for at least 1 second within 5 seconds after pushing the set switch.
NOTE:
• To enter driver seat positions into blank memory, memory indicator will be turned on for 5 seconds.
• To modify driver seat positions, memory indicator will be turned OFF for 0.5 second, then turned ON for
5 seconds.
NOTE:
If memory is stored in the same memory switch, the previous memory will be deleted.
Do you need linking of Intelligent Key?
YES
>> GO TO 6.
NO
>> GO TO 5.
5.
STEP 5
Confirm the operation of each part with memory operation.
>> END
6.
STEP 6
Push the Intelligent Key unlock button within 5 seconds after pushing memory switch (while the memory indi-
cator is turned ON).
>> GO TO 7.
7.
STEP 7
Confirm the operation of each part with memory operation and lntelligent Key interlock operation.
INSPECTION AND ADJUSTMENT
ADP-11
< BASIC INSPECTION >
C
D
E
F
G
H
I
K
L
M
A
B
ADP
N
O
P
>> END
SYSTEM SETTING
SYSTEM SETTING : Description
INFOID:0000000000960585
The settings of the automatic driving positioner system can be changed, using CONSULT-III, the display unit
in the center of the instrument panel and the set switch. Always check the settings before and after discon-
necting the battery terminal or replacing driver seat control unit.
Setting Change ( For AT models)
×
: Applicable
*1
: If either of entry/exit assist (seat) or entry/exit assist (steering column) is turned OFF, seat synchronizaton function is also turned OFF.
Setting Change (For MT models)
×
: Applicable
SYSTEM SETTING : Special Repair Requirement
INFOID:0000000000960586
1.
CHECK TYPE OF TRANSMISSION
Check type of transmission for the vehicle.
Witch type of transmission is used for the vehicle?
MT
>> GO TO 2.
AT
>> GO TO 4.
2.
STEP 1 (FOR MT MODELS)
Turn ignition switch OFF.
>> GO TO 3.
3.
STEP 2 (FOR MT MODELS)
Push setting button and hold for more than 10 seconds, then confirm blinking of the memory switch indicator.
• Seat synchronization function is ON: Memory switch indicator blink two times.
• Seat synchronization is OFF: Memory switch indicator blink once.
>> END
4.
CHOOSE METHOD
There are three way of setting method.
Item
Content
CON-
SULT
–III
Display
Set
switch
Factory
setting
Amount of seat sliding for
entry/exit assist
The amount of seat sliding for entry/exit assist can
be selected from 3 items.
[40mm/80mm/150mm]
x
—
—
40mm
Entry/exit assist
(seat)
Entry/exit assist (seat) can be selected:
ON (operated) – OFF (not operated)
x
x
x
OFF
Entry/exit assist
(steering column)
Entry/exit assist (steering column) can be selected:
ON (operated) – OFF (not operated)
x
x
OFF
Seat synchronization
Seat synchronization can be selected: ON (operat-
ed) – OFF (not operated)
NOTE:
*1
OFF
Reset custom settings
All settings can be set to default (factory setting).
—
x
—
—
Item
Content
Set switch
Factory
setting
Seat synchronization
Seat synchronization can be selected:
ON (operated) – OFF (not operated)
x
OFF
ADP-12
< BASIC INSPECTION >
INSPECTION AND ADJUSTMENT
Which method do you choose?
With display>>GO TO 5.
With set switch>>GO TO 7.
With CONSULT-III>>GO TO 9.
5.
WITH DISPLAY - STEP 1 (FOR AT MODELS)
Turn ignition switch ON.
>> GO TO 6.
6.
WITH DISPLAY - STEP 2 (FOR AT MODELS)
1.
Push “SETTING” button.
2.
Select “Comfort & convenience”.
3.
Select “Lift Steering Wheel ON Exit”or “Slide Driver
′
s Seat Back ON Exit” on display, then push
-
Lift Steering Wheel ON Exit: Entry/exit assist (steering column)
-
Slide Driver's Seat Back On Exit: Entry/exit assist (seat)
NOTE:
If either of entry/exit assist (seat) or entry/exit assist (steering column) is turned OFF, seat synchronization
function is also turned OFF.
>> END
7.
WITH SET SWITCH - STEP 1 (FOR AT MODELS)
Turn ignition switch OFF.
>> GO TO 8.
8.
WITH SET SWITCH - STEP 2 (FOR AT MODELS)
Push setting button and hold for more than 10 seconds, then confirm blinking of the memory switch indicator.
• Entry/exit assist (seat/steering column) and seat synchronization are ON: Memory switch indicator blink two
times.
• Entry/exit assist (seat/steering column) and seat synchronization are OFF: Memory switch indicator blink
once.
>> END
9.
WITH CONSULT-III - STEP 1 (FOR AT MODELS)
Select “Work support”.
>> GO TO 10.
10.
WITH CONSULT-III - STEP 2 (FOR AT MODELS)
1.
Select “EXIT SEAT SLIDE SETTING”, “EXIT TILT SETTING” or “SEAT SLIDE VOLUME SET” then touch
display to change between ON and OFF.
-
EXIT SEAT SLIDE SETTING: Entry/exit assist (seat)
-
EXIT TILT SETTING: Entry/exit assist (steering column)
2.
Then touch “OK”.
NOTE:
If either of entry/exit assist (seat) or entry/exit assist (steering column) is turned OFF, seat synchronization
function is also turned OFF.
>> END
AUTOMATIC DRIVE POSITIONER SYSTEM
ADP-13
< FUNCTION DIAGNOSIS >
C
D
E
F
G
H
I
K
L
M
A
B
ADP
N
O
P
FUNCTION DIAGNOSIS
AUTOMATIC DRIVE POSITIONER SYSTEM
AUTOMATIC DRIVE POSITIONER SYSTEM
AUTOMATIC DRIVE POSITIONER SYSTEM : System Diagram
INFOID:0000000000960587
JMJIA0113GB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст