Infiniti G35 (V35) Sedan. Manual — part 256
BRC-98
< PRECAUTION >
[VDC/TCS/ABS]
PRECAUTIONS
• If aftermarket parts (car stereo, CD player, etc.) have been installed, check for incidents such as harness
pinches, open circuits, and improper wiring.
• VDC system may not operate normally or a VDC OFF indicator lamp or SLIP indicator lamp may light.
- When replacing the following parts with parts other than genuine parts or making modifications: Suspension
related parts (shock absorber, spring, bushing, etc.), tires, wheels (other than specified sizes), brake-related
parts (pad, rotor, caliper, etc.), engine-related parts (muffler, ECM, etc.) and body reinforcement-related parts
(roll bar, tower bar, etc.).
- When driving with worn or deteriorated suspension, tires and brake-related parts.
PREPARATION
BRC-99
< PREPARATION >
[VDC/TCS/ABS]
C
D
E
G
H
I
J
K
L
M
A
B
BRC
N
O
P
PREPARATION
PREPARATION
Special Service Tool
INFOID:0000000000958637
The actual shapes of Kent-Moore tools may differ from those of special service tools illustrated here.
Commercial Service Tool
INFOID:0000000000958638
Tool number
(Kent-Moore No.)
Tool name
Description
ST30720000
(J-25405)
Drift
a: 77 mm (3.03 in) dia.
b: 55.5 mm (2.185 in) dia.
Installing rear sensor rotor
ST27863000
(
—
)
Drift
a: 74.5 mm (2.933 in) dia.
b: 62.5 mm (2.461 in) dia.
KV40104710
(
—
)
a: 76.3 mm (3.004 in) dia.
b: 67.9 mm (2.673 in) dia.
ZZA0701D
ZZA0832D
ZZA0832D
Tool name
Description
1. Flare nut crowfoot
a: 10 mm (0.39 in) /12 mm (0.47 in)
2. Torque wrench
Installing brake tube
S-NT360
BRC-100
< ON-VEHICLE REPAIR >
[VDC/TCS/ABS]
WHEEL SENSOR
ON-VEHICLE REPAIR
WHEEL SENSOR
Exploded View
INFOID:0000000000958639
NOTE:
The above figure (front side) shows left side. Right side is the mirror image.
Removal and Installation
INFOID:0000000000958640
REMOVAL
Pay attention to the following when removing sensor.
CAUTION:
• Do not twist sensor harness as much as possible, when removing it. Pull sensors out without pulling
on sensor harness.
• Take care to avoid damaging sensor edges or rotor teeth. Remove wheel sensor first before remov-
ing front or rear wheel hub. This is to avoid damage to sensor wiring and loss of sensor function.
INSTALLATION
Pay attention to the following when installing wheel sensor. Tighten installation bolts to the specified torques.
Refer to
.
• When installing, make sure there is no foreign material such as iron chips on and in the mounting hole of the
wheel sensor. Make sure no foreign material has been caught in the sensor rotor. Remove any foreign mate-
rial and clean the mount.
• When installing wheel sensor, be sure to press rubber grommets in until they lock at locations shown above
in the figure. When installed, harness must not be twisted.
1.
Front LH wheel sensor
2.
Rear LH wheel sensor
3.
Rear RH wheel sensor
A.
Front
B.
Rear
: Vehicle front
Refer to GI section
for symbol marks in the figure.
JSFIA0001GB
SENSOR ROTOR
BRC-101
< ON-VEHICLE REPAIR >
[VDC/TCS/ABS]
C
D
E
G
H
I
J
K
L
M
A
B
BRC
N
O
P
SENSOR ROTOR
FRONT SENSOR ROTOR
FRONT SENSOR ROTOR : Exploded View
INFOID:0000000000958641
(2WD models),
(AWD models).
FRONT SENSOR ROTOR : Removal and Installation
INFOID:0000000000958642
REMOVAL
Sensor rotor cannot be disassembled. Remove the sensor rotor together with hub bearing assembly. Refer to
FAX-6, "Removal and Installation"
(2WD models),
FAX-16, "Removal and Installation"
(AWD models).
INSTALLATION
Sensor rotor cannot be disassembled. Remove the sensor rotor together with hub bearing assembly. Refer to
FAX-6, "Removal and Installation"
(2WD models),
FAX-16, "Removal and Installation"
(AWD models).
REAR SENSOR ROTOR
REAR SENSOR ROTOR : Exploded View
INFOID:0000000000958643
REAR SENSOR ROTOR : Removal and Installation
INFOID:0000000000958644
REMOVAL
• Follow the procedure below to remove rear sensor rotor.
- Remove side flange. Refer to
RAX-10, "Disassembly and Assembly"
.
- Using a bearing replacer (suitable tool) and puller (suitable tool), remove sensor rotor from side flange.
INSTALLATION
CAUTION:
Do not reuse sensor rotor.
• Follow the procedure below to install rear sensor rotor.
- Using a drifts, press rear sensor rotor onto side flange.
- Install side flange. Refer to
RAX-10, "Disassembly and Assembly"
1.
Side flange
2.
Rear wheel sensor rotor
JSFIA0008ZZ
A: Drift [SST: ST30720000 (J-25405)]
B: Drift [SST: ST27863000 (
—
)]
C: Drift [SST: KV40104710 (
—
)]
SFIA3387E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст