Infiniti G35 (V35) Sedan. Manual — part 22
ADP-82
< COMPONENT DIAGNOSIS >
SEAT MEMORY SWITCH
SEAT MEMORY SWITCH
Description
INFOID:0000000000960677
Memory switch is equipped on the seat memory switch installed to the driver side door trim. The operation sig-
nal is inputted to the automatic drive positioner control unit when the memory switch is operated.
Component Function Check
INFOID:0000000000960678
1.
CHECK FUNCTION
1.
Select “MEMORY SW 1”, “MEMORY SW 2” in “Data monitor” mode with CONSULT-III.
2.
Check seat memory switch signal under the following conditions.
Is the indication normal?
YES
>> INSPECTION END
NO
>> Perform diagnosis procedure. Refer to
Diagnosis Procedure
INFOID:0000000000960679
1.
CHECK SEAT MEMORY SWITCH SIGNAL
1.
Turn ignition switch ON.
2.
Check voltage between automatic drive positioner control unit harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 6.
NO
>> GO TO 2.
2.
CHECK MEMORY SWITCH CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect automatic drive positioner control unit and seat memory switch connector.
3.
Check continuity between automatic drive positioner control unit harness connector and seat memory
switch harness connector.
4.
Check continuity between automatic drive positioner control unit harness connector and ground.
Monitor item
Condition
Status
MEMORY SW 1
Memory switch 1
Push
ON
Release
OFF
MEMORY SW 2
Memory switch 2
Push
ON
Release
OFF
Automatic drive positioner
control unit connector
Terminals
Condition
Voltage (V)
(Approx.)
(+)
(–)
M51
9
Ground
Memory switch 1
Push
0
Release
5
25
Memory switch 2
Push
0
Release
5
Automatic drive positioner
control unit connector
Terminal
Seat memory switch
connector
Terminal
Continuity
M51
9
D5
1
Existed
25
2
SEAT MEMORY SWITCH
ADP-83
< COMPONENT DIAGNOSIS >
C
D
E
F
G
H
I
K
L
M
A
B
ADP
N
O
P
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace harness.
3.
CHECK MEMORY SWITCH GROUND CIRCUIT
Check continuity between seat memory switch harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair or replace harness.
4.
CHECK AUTOMATIC DRIVE POSITIONER CONTROL UNIT OUTPUT
1.
Connect the automatic drive positioner control unit connector.
2.
Turn ignition switch ON.
3.
Check voltage between automatic drive positioner control unit harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> Replace automatic drive positioner control unit.
5.
CHECK SEAT MEMORY SWITCH
ADP-83, "Component Inspection"
.
Is the inspection result normal?
YES
>> GO TO 6.
NO
>> Replace seat memory switch.
6.
CHECK INTERMITTENT INCIDENT
GI-39, "Intermittent Incident"
.
Is the inspection result normal?
YES
>> Replace automatic drive positioner control unit.
NO
>> Repair or replace the malfunctioning part.
Component Inspection
INFOID:0000000000960680
1.
CHECK SEAT MEMORY SWITCH
1.
Turn ignition switch OFF.
2.
Disconnect seat memory switch connector.
3.
Check continuity between seat memory switch terminals.
Automatic drive positioner
control unit connector
Terminal
Ground
Continuity
M51
9
Not existed
25
Seat memory switch
connector
Terminal
Ground
Continuity
D5
4
Existed
Automatic drive positioner
control unit connector
Terminals
Voltage (V)
(Approx.)
(+)
(–)
M51
9
Ground
5
25
ADP-84
< COMPONENT DIAGNOSIS >
SEAT MEMORY SWITCH
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Replace seat memory switch.
Terminal
Condition
Continuity
Seat memory switch
4
1
Memory switch 1
Push
Existed
Release
Not existed
2
Memory switch 2
Push
Existed
Release
Not existed
DOOR MIRROR REMOTE CONTROL SWITCH
ADP-85
< COMPONENT DIAGNOSIS >
C
D
E
F
G
H
I
K
L
M
A
B
ADP
N
O
P
DOOR MIRROR REMOTE CONTROL SWITCH
CHANGEOVER SWITCH
CHANGEOVER SWITCH : Description
INFOID:0000000000960681
Changeover switch is integrated into door mirror remote control switch.
Changeover switch has three positions (L, N and R).
It changes door mirror motor operation by transmitting control signal to automatic drive positioner control unit.
CHANGEOVER SWITCH : Component Function Check
INFOID:0000000000960682
1.
CHECK CHANGEOVER SWITCH FUNCTION
Check the operation on “MIR CHNG SW-R” or “MIR CHNG SW-L” in “DATA MONITOR” mode with CON-
SULT-III.
Refer to
ADP-48, "CONSULT-III Function"
.
Is the inspection result normal?
YES
>> Changeover switch function is OK.
NO
>> Refer to
ADP-85, "CHANGEOVER SWITCH : Diagnosis Procedure"
.
CHANGEOVER SWITCH : Diagnosis Procedure
INFOID:0000000000960683
1.
CHECK CHANGEOVER SWITCH SIGNAL
1.
Turn ignition switch ON.
2.
Check voltage between automatic drive positioner control unit connector and ground.
Is the inspection result normal?
YES
>> GO TO 6.
NO
>> GO TO 2.
2.
CHECK HARNESS CONTINUITY
1.
Turn ignition switch OFF.
2.
Disconnect automatic drive positioner control unit and door mirror remote control switch connector.
3.
Check continuity between automatic drive positioner control unit connector and door mirror remote control
switch connector.
4.
Check continuity between automatic drive positioner control unit connector and ground.
Is the inspection result normal?
Terminals
Change over switch condition
Voltage (V)
(Approx.)
(+)
(-)
Automatic drive positioner
control unit connector
Terminal
M51
2
Ground
RIGHT
0
Other than above
5
18
LEFT
0
Other than above
5
Automatic drive positioner
control unit connector
Terminal
Door mirror remote control switch
connector
Terminal
Continuity
M51
2
D7
11
Existed
18
10
Automatic drive positioner control unit
connector
Terminal
Ground
Continuity
M51
2
Not existed
18
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст