Infiniti G35 (V35) Sedan. Manual — part 1219
SRC-24
< COMPONENT DIAGNOSIS >
B1006, B1007, B1008, B1009, B1010 DIAGNOSIS SENSOR UNIT
With CONSULT-lll
CAUTION:
• Before servicing, turn ignition switch OFF, disconnect both battery terminals and wait at least 3 min-
utes. (To discharge backup capacitor.)
• Do not use unspecified tester or other measuring device.
DIAGNOSTIC PROCEDURE
1.
CHECK HARNESS CONNECTOR
Check the harness connector.
Are connections of harness connectors and terminals correct?
YES
>> GO TO 2.
NO
>> Repair or replace harness connectors.
2.
CHECK WIRING HARNESS
Check the wiring harness.
Is the outside of wiring harness normal, without any damage?
YES
>> GO TO 3.
NO
>> Replace wiring harness.
3.
CHECK DIAGNOSIS SENSOR UNIT
Check the displayed on CONSULT-lll?
Is “DIAGNOSIS SENSOR UNIT” displayed on CONSULT-lll?
YES
>> Replace diagnosis sensor unit (ACU).
>> INSPECTION END.
B1011, B1012, B1013, B1014, B1015 DIAGNOSIS SENSOR UNIT
SRC-25
< COMPONENT DIAGNOSIS >
C
D
E
F
G
I
J
K
L
M
A
B
SRC
N
O
P
B1011, B1012, B1013, B1014, B1015 DIAGNOSIS SENSOR UNIT
Description
INFOID:0000000000959603
DTC B1011, B1012, B1013, B1014, B1015 DIAGNOSIS SENSOR UNIT
Detects the whole SRS electrical system and displays the malfunction either by illuminating or blinking the air
bag warning lamp in the combination meter Malfunctioning part can be detected by on board self-diagnosis
system and electro-diagnosis tester “CONSULT-lll”.
OPERATION
It detects a shock that exceeds specified level and watches such systems as the driver and passenger air bag,
side air bag, curtain air bag, pre-tensioner seat belts and Occupant Classification System (OCS) operate prop-
erly.
STRUCTURE
It contains the “G” sensors of both for frontal collision and for side collision and spare battery function in case
of main battery damage in collision.
INSTALLATION
SRS diagnosis sensor unit is installed under the center console with fixed bolts.
DTC Logic
INFOID:0000000000959604
DTC DETECTION LOGIC
With CONSULT-lll
DTC No. Index (“SELF-DIAG [CURRENT]”), (“SELF-DIAG [PAST]” or “TROUBLE DIAG RECORD”)
Without CONSULT-lll
Warning Lamp Flash Code Chart
DTC CONFIRMATION PROCEDURE (With CONSULT-lll)
1.
IGNITION SWITCH
Turn ignition switch ON.
>> GO TO 2.
2.
CONSULT-LLL
Select “DIAG MODE” with CONSULT-lll.
DTC No.
Trouble diagnosis name
DTC detecting condition
Possible cause
B1011
B1012
B1013
B1014
B1015
CONTROL UNIT
Diagnosis sensor unit is out of order.
1.
Replace diagnosis sensor unit
(ACU).
JMHIA0034GB
SRC-26
< COMPONENT DIAGNOSIS >
B1011, B1012, B1013, B1014, B1015 DIAGNOSIS SENSOR UNIT
>> GO TO 3.
3.
DTC CODE
If DTC is detected. Refer to
>> END
DTC CONFIRMATION PROCEDURE (Without CONSULT-lll)
NOTE:
• SRS will not enter diagnosis mode if no malfunction is detected in user mode.
1.
IGNITION SWITCH
Turn ignition switch ON.
>> GO TO 2.
2.
USER MODE-DIAG MODE
After air bag warning lamp illuminates for 7 seconds, turn ignition switch OFF within 1 second.
>> GO TO 3.
3.
USER MODE-DIAG MODE
Wait more than 3 seconds.
>> GO TO 4.
4.
USER MODE-DIAG MODE
Repeat step 1 to 3 twice. (Perform three times in all.)
>> GO TO 5.
5.
DIAG MODE
Turn ignition switch ON. (SRS is now in diagnosis mode.)
>> GO TO 6.
6.
DIAG MODE (AIR BAG WARNING LAMP)
Malfunctioning portion is indicated according to blinking times of air bag warning lamp. Refer to
>> END
Diagnosis Procedure (Component diagnosis)
INFOID:0000000000959605
B1011, B1012, B1013, B1014, B1015 DIAGNOSIS SENSOR UNIT
SRC-27
< COMPONENT DIAGNOSIS >
C
D
E
F
G
I
J
K
L
M
A
B
SRC
N
O
P
With CONSULT-lll
CAUTION:
• Before servicing, turn ignition switch OFF, disconnect both battery terminals and wait at least 3 min-
utes. (To discharge backup capacitor.)
• Do not use unspecified tester or other measuring device.
DIAGNOSTIC PROCEDURE
1.
CHECK HARNESS CONNECTOR
Check the harness connector.
Are connections of harness connectors and terminals correct?
YES
>> GO TO 2.
NO
>> Repair or replace harness connectors.
2.
CHECK WIRING HARNESS
Check the wiring harness.
Is the outside of wiring harness normal, without any damage?
YES
>> GO TO 3.
NO
>> Replace wiring harness.
3.
CHECK DIAGNOSIS SENSOR UNIT
Check the displayed on CONSULT-lll?
Is “DIAGNOSIS SENSOR UNIT” displayed on CONSULT-lll?
YES
>> Replace diagnosis sensor unit (ACU).
>> INSPECTION END.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст