Infiniti G35 (V35) Sedan. Manual — part 451
DLN-238
< ON-VEHICLE REPAIR >
[REAR FINAL DRIVE: R200V]
SIDE OIL SEAL
SIDE OIL SEAL
M/T
M/T : Exploded View
INFOID:0000000000957434
1.
Drive pinion lock nut
2.
Companion flange
3.
Front oil seal
4.
Pinion front bearing
5.
Gear carrier
6.
Side oil seal
7.
Side flange
8.
Collapsible spacer
9.
Pinion rear bearing
10. Pinion height adjusting washer
11.
Drive pinion
12. Side bearing adjusting washer
13. Side bearing
14. Drive gear
15. Differential case B
16. Side gear thrust washer
17. Circular clip
18. Side gear
19. Pinion mate shaft
20. Pinion mate thrust washer
21. Pinion mate gear
22. Viscous coupling
23. Differential case A
24. Bearing cap
25. Filler plug
26. Gasket
27. Rear cover
28. Drain plug
A: Oil seal lip
B: Screw hole
C: After tightening the bolts to the specified torque, tighten the bolts additionally by turning the bolts 31 to 36 degrees.
:
Apply gear oil.
:
Apply anti-corrosion oil.
:
Apply Genuine Silicone RTV or equivalent. Refer to
GI-15, "Recommended Chemical Products and Sealants"
:
Apply Genuine High Strength Thread Locking Sealant or equivalent. Refer to
GI-15, "Recommended Chemical Products
Refer to
for symbols not described on the above.
JSDIA0037GB
SIDE OIL SEAL
DLN-239
< ON-VEHICLE REPAIR >
[REAR FINAL DRIVE: R200V]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
M/T : Removal and Installation
INFOID:0000000000957435
REMOVAL
1.
Remove center muffler with a power tool. Refer to
EX-5, "Removal and Installation"
.
2.
Remove rear wheel sensor. Refer to
BRC-100, "Removal and Installation"
3.
Remove drive shaft from final drive with a power tool. Then suspend it by wire etc. Refer to
4.
Install attachment (A) [SST: KV40104100 (
—
)] to side
flange, and then pull out the side flange with the sliding hammer
(B) [SST: ST36230000 (J-25840-A)].
NOTE:
Circular clip installation position: Final drive side
5.
Remove side oil seal, using a flat-bladed screwdriver.
CAUTION:
Never damage gear carrier.
INSTALLATION
1.
Apply multi-purpose grease to side oil seal lips.
2.
Install side oil seal until it becomes flush with the case end,
using the drift [SST: KV38100200 (J-26233)].
CAUTION:
• Never reuse oil seal.
• When installing, never incline oil seal.
3.
Install side flange with the following procedure.
a.
Attach the protector [SST: KV38107900 (J-39352)] to side oil
seal.
b.
After the side flange is inserted and the serrated part of side
gear has engaged the serrated part of flange, remove the pro-
tector.
c.
Put a suitable drift on the center of side flange, then drive it until sound changes.
JSDIA0105ZZ
SDIA1584E
SDIA1585E
SDIA0822E
DLN-240
< ON-VEHICLE REPAIR >
[REAR FINAL DRIVE: R200V]
SIDE OIL SEAL
NOTE:
When installation is completed, driving sound of the side flange turns into a sound which seems to affect
the whole final drive.
d.
Confirm that the dimension of the side flange (1) installation
(Measurement A) in the figure comes into the following.
4.
Install drive shaft. Refer to
RAX-9, "Removal and Installation"
.
5.
Install rear wheel sensor. Refer to
.
6.
Install center muffler. Refer to
EX-5, "Removal and Installation"
.
7.
When oil leaks while removing, check oil level after the installa-
tion. Refer to
.
A/T
A/T : Exploded View
INFOID:0000000000957436
Measurement “A”
: 326 – 328 mm (12.83 –
12.91 in)
JSDIA0109ZZ
1.
Drive pinion lock nut
2.
Companion flange
3.
Front oil seal
4.
Pinion front bearing
5.
Gear carrier
6.
Side oil seal
7.
Side flange
8.
Collapsible spacer
9.
Pinion rear bearing
10. Pinion height adjusting washer
11.
Drive pinion
12. Side bearing adjusting washer
13. Side bearing
14. Drive gear
15. Differential case B
16. Side gear thrust washer
17. Circular clip
18. Side gear
19. Pinion mate shaft
20. Pinion mate thrust washer
21. Pinion mate gear
22. Viscous coupling
23. Differential case A
24. Bearing cap
JSDIA0045GB
SIDE OIL SEAL
DLN-241
< ON-VEHICLE REPAIR >
[REAR FINAL DRIVE: R200V]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
A/T : Removal and Installation
INFOID:0000000000957437
REMOVAL
1.
Remove center muffler with a power tool. Refer to
EX-5, "Removal and Installation"
.
2.
Remove rear wheel sensor. Refer to
BRC-100, "Removal and Installation"
3.
Remove drive shaft from final drive with a power tool. Then suspend it by wire etc. Refer to
4.
Install attachment (A) [SST: KV40104100 (
—
)] to side
flange, and then pull out the side flange with the sliding hammer
(B) [SST: ST36230000 (J-25840-A)].
NOTE:
Circular clip installation position: Final drive side
5.
Remove side oil seal, using a flat-bladed screwdriver.
CAUTION:
Never damage gear carrier.
INSTALLATION
1.
Apply multi-purpose grease to side oil seal lips.
25. Filler plug
26. Gasket
27. Rear cover
28. Drain plug
A: Oil seal lip
B: Screw hole
C: After tightening the bolts to the specified torque, tighten the bolts additionally by turning the bolts 31 to 36 degrees.
:
Apply gear oil.
:
Apply anti-corrosion oil.
:
Apply Genuine Silicone RTV or equivalent. Refer to
GI-15, "Recommended Chemical Products and Sealants"
:
Apply Genuine High Strength Thread Locking Sealant or equivalent. Refer to
GI-15, "Recommended Chemical Products
Refer to
for symbols not described on the above.
JSDIA0105ZZ
SDIA1584E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст