Infiniti G35 (V35) Sedan. Manual — part 624
REAR TIMING CHAIN CASE
EM-95
< DISASSEMBLY AND ASSEMBLY >
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
f.
After installing rear timing chain case, check the surface height
difference between the following parts on the oil pan (upper)
mounting surface.
• If not within the standard, repeat the installation procedure.
3.
Install water pump with new O-rings. Refer to
.
4.
Make sure that dowel pin (A) and crankshaft key (1) are located
as shown in the figure. (No. 1 cylinder at compression TDC)
NOTE:
Though camshaft does not stop at the position as shown in the
figure, for the placement of cam nose, it is generally accepted
camshaft is placed for the same direction of the figure.
5.
Install timing chains (secondary) and camshaft sprockets as follows:
CAUTION:
Mating marks between timing chain and sprockets slip easily. Confirm all mating mark positions
repeatedly during the installation process.
a.
Push plunger of timing chain tensioner (secondary) and keep it
pressed in with a stopper pin (A).
6.
For the following operations, perform steps in the reverse order of removal.
1
: Front timing chain case
2
: Rear timing chain case
3
: Lower cylinder block
Standard
Rear timing chain case to lower cylinder block:
–0.24 to 0.14 mm (–0.0094 to 0.0055 in)
JPBIA0093ZZ
Camshaft dowel pin
: At cylinder head upper face side in each bank.
Crankshaft key
: At cylinder head side of right bank.
JPBIA0094ZZ
JPBIA0095ZZ
EM-96
< DISASSEMBLY AND ASSEMBLY >
OIL PAN (UPPER) AND OIL STRAINER
OIL PAN (UPPER) AND OIL STRAINER
2WD
2WD : Exploded View
INFOID:0000000000956277
2WD : Disassembly and Assembly
INFOID:0000000000956278
REMOVAL
CAUTION:
To avoid the danger of being scalded, never drain engine oil when the engine is hot.
1.
Remove oil level gauge, oil pressure switch and oil temperature sensor.
1.
Oil level gauge
2.
Oil level gauge guide
3.
O-ring
4.
O-ring
5.
Connector bolt
6.
Oil filter
7.
Plug
8.
Oil pressure switch
9.
Oil strainer
10. Oil temperature sensor
11.
Washer
12. Oil pan (upper)
13. Drain plug
14. Drain plug washer
15. Oil pan (lower)
16. Rear plate cover
17. Rear cover plate (M/T models)
A.
Refer to
B.
To oil pump
C.
Oil pan side
for symbol marks in the figure.
JPBIA0008ZZ
OIL PAN (UPPER) AND OIL STRAINER
EM-97
< DISASSEMBLY AND ASSEMBLY >
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
2.
Remove oil pan (lower). Refer to
.
3.
Remove oil strainer.
4.
Loosen mounting bolts in the reverse order as shown in the fig-
ure with power tool to remove.
• Insert the seal cutter [SST: KV10111100 (J37228)] between oil
pan (upper) and lower cylinder block. Slide seal cutter by tap-
ping on the side of tool with a hammer. Remove oil pan
(upper).
CAUTION:
• Be careful not to damage the mating surfaces.
• Do not insert a screwdriver, this will damage the mating
surfaces.
5.
Remove o-rings (2) from bottom of lower cylinder block (1) and
oil pump (3).
INSTALLATION
1.
Install oil pan (upper) as follows:
a.
Use a scraper (A) to remove old liquid gasket from mating sur-
faces.
CAUTION:
Do not scratch or damage the mating surfaces when clean-
ing off old liquid gasket.
• Also remove old liquid gasket from mating surface of lower cyl-
inder block.
• Remove old liquid gasket from the bolt holes and threads.
b.
Install new O-rings (2) on the bottom of lower cylinder block (1)
and oil pump (3).
: Engine front
JPBIA0022ZZ
: Engine front
JPBIA0024ZZ
JPBIA0027ZZ
: Engine front
JPBIA0024ZZ
EM-98
< DISASSEMBLY AND ASSEMBLY >
OIL PAN (UPPER) AND OIL STRAINER
c.
Apply a continuous bead of liquid gasket with the tube presser
[SST: WS39930000 (
—
)] to the cylinder block mating sur-
face of oil pan (upper) to a limited portion as shown in the figure.
Use Genuine RTV Silicone Sealant or equivalent. Refer to
GI-15, "Recommended Chemical Products and Sealants"
.
CAUTION:
• For bolt holes with marks (7 locations), apply liquid
gasket outside the holes.
• Attaching should be done within 5 minutes after coating.
d.
Install oil pan (upper).
CAUTION:
Install avoiding misalignment of both O-rings.
• Tighten mounting bolts in numerical order as shown in the fig-
ure.
• There are two types of mounting bolts. Refer to the following
for locating bolts.
2.
Install oil strainer to oil pump.
3.
Install oil pan (lower). Refer to
4.
Install oil pan drain plug.
• Refer to the figure of components of former page for installation direction of drain plug washer. Refer to
.
5.
Install in the reverse order of removal after this step.
NOTE:
At least 30 minutes after oil pan is installed, pour engine oil.
2WD : Inspection
INFOID:0000000000956279
INSPECTION AFTER REMOVAL
Clean oil strainer if any object attached.
INSPECTION AFTER INSTALLATION
1.
Check the engine oil level and adjust engine oil. Refer to
2.
Start engine, and check there is no leak of engine oil.
3.
Stop engine and wait for 10 minutes.
4.
Check the engine oil level again. Refer to
.
AWD
AWD : Exploded View
INFOID:0000000000956280
a
: 4.0 - 5.0 mm (0.157 - 0.197 in)
: Engine front
: Engine front
M8
×
90 mm (3.54 in)
: 7, 10, 13
M8
×
25 mm (0.98 in)
: Except the above
JPBIA0388ZZ
JPBIA0022ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст