Infiniti G35 (V35) Sedan. Manual — part 1358
TM-124
< COMPONENT DIAGNOSIS >
[5AT: RE5R05A]
P0705 PARK/NEUTRAL POSITION SWITCH
P0705 PARK/NEUTRAL POSITION SWITCH
Description
INFOID:0000000000957020
• The park/neutral position (PNP) switch includes the transmission range switch.
• The transmission range switch detects the selector lever position and transmits a signal to the TCM.
DTC Logic
INFOID:0000000000957021
DTC DETECTION LOGIC
*: This is an OBD-II self-diagnostic item.
DTC CONFIRMATION PROCEDURE
CAUTION:
Always drive vehicle at a safe speed.
NOTE:
If “DTC CONFIRMATION PROCEDURE” has been previously performed, always turn ignition switch
OFF and wait at least 10 seconds before performing the next test.
After the repair, perform the following procedure to confirm the malfunction is eliminated.
1.
CHECK DTC DETECTION
With CONSULT-III
1.
Start the engine.
2.
Select “DATA MONITOR”.
3.
Drive vehicle and maintain the following conditions for least 2 consecutive seconds.
With GST
Follow the procedure “With CONSULT-III”.
Is “P0705 PNP SW/CIRC” detected?
YES
>> Go to
NO
>> Check Intermittent incident. Refer to
GI-39, "Intermittent Incident"
.
Diagnosis Procedure
INFOID:0000000000957022
1.
CHECK TCM POWER SUPPLY AND GROUND CIRCUIT
Check TCM power supply and ground circuit. Refer to
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace damaged parts.
2.
CHECK PARK/NEUTRAL POSITION SWITCH HARNESS CONNECTOR AND TCM HARNESS CONNEC-
TOR
1.
Remove control valve with TCM. Refer to
.
2.
Disconnect park/neutral position switch connector and TCM connector.
3.
Check continuity between park/neutral position switch connector and TCM connector.
DTC
Item
(CONSULT-III screen
terms)
A/T CHECK indicator
lamp judgment flicker
Diagnostic item is de-
tected when...
Possible cause
P0705*
PNP SW/CIRC
9th
• PNP switch 1 – 4 sig-
nals input with impos-
sible pattern.
• P position is detected
from N position with-
out any other position
being detected in be-
tween.
• Harness or connectors
[Park/neutral position
(PNP) switches 1, 2, 3,
4 and TCM circuit is
open or shorted.]
• Park/neutral position
(PNP) switches 1, 2, 3
and 4
ACCELE POSI
: More than 1.0/8
P0705 PARK/NEUTRAL POSITION SWITCH
TM-125
< COMPONENT DIAGNOSIS >
[5AT: RE5R05A]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
4.
If OK, check harness for short to ground and short to power.
Is the inspection result normal?
YES
>> Replace the control valve with TCM. Refer to
NO
>> Replace open circuit or short to ground and short to power in harness or connectors.
Park/neutral position switch connector
TCM connector
Continuity
Connector
Terminal
Connector
Terminal
F154
1
F152
13
Existed
2
11
Existed
3
12
Existed
5
14
Existed
TM-126
< COMPONENT DIAGNOSIS >
[5AT: RE5R05A]
P0717 TURBINE REVOLUTION SENSOR
P0717 TURBINE REVOLUTION SENSOR
Description
INFOID:0000000000957023
The turbine revolution sensor detects input shaft rpm (revolutions per minute). It is located on the input side of
the A/T. Monitors revolution of sensor 1 and sensor 2 for non-standard conditions.
DTC Logic
INFOID:0000000000957024
DTC DETECTION LOGIC
*: This is an OBD-II self-diagnostic item.
DTC CONFIRMATION PROCEDURE
CAUTION:
Always drive vehicle at a safe speed.
NOTE:
If “DTC CONFIRMATION PROCEDURE” has been previously performed, always turn ignition switch
OFF and wait at least 10 seconds before performing the next test.
After the repair, perform the following procedure to confirm the malfunction is eliminated.
1.
CHECK DTC DETECTION
With CONSULT-III
1.
Start the engine.
2.
Select “DATA MONITOR”.
3.
Drive vehicle and maintain the following conditions for at least 5 consecutive seconds.
With GST
Follow the procedure “With CONSULT-III”.
Is “P0717 TURBINE REV S/CIRC” detected?
YES
>> Go to
NO
>> Check Intermittent incident. Refer to
GI-39, "Intermittent Incident"
.
Diagnosis Procedure
INFOID:0000000000957025
1.
CHECK TCM POWER SUPPLY AND GROUND CIRCUIT
Check TCM power supply and ground circuit. Refer to
Is the inspection result normal?
DTC
Item
(CONSULT-III screen
terms)
A/T CHECK indicator
lamp judgment flicker
Diagnostic item is de-
tected when...
Possible cause
P0717*
TURBINE REV S/CIRC
11th
• TCM does not receive
the proper voltage sig-
nal from the sensor.
• TCM detects an irreg-
ularity only at position
of 4th gear for turbine
revolution sensor 2.
• Harness or connectors
(Sensor circuit is open
or shorted.)
• Turbine revolution
sensor 1 and/or 2
VHCL/S SE-A/T
: 40 km/h (25 MPH) or more
ACCELE POSI
: More than 0.5/8
ENGINE SPEED
: 1,500 rpm or more
SLCT LVR POSI
: “D” position
GEAR (Turbine revo-
lution sensor 1)
: “4” or “5” position
GEAR (Turbine revo-
lution sensor 2)
: All positions
Driving location
: Driving the vehicle uphill (increased engine load) will help maintain the driving con-
ditions required for this test.
P0717 TURBINE REVOLUTION SENSOR
TM-127
< COMPONENT DIAGNOSIS >
[5AT: RE5R05A]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
YES
>> Replace the control valve with TCM. Refer to
NO
>> Repair or replace damaged parts.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст