Infiniti G35 (V35) Sedan. Manual — part 982
MWI
AIR BAG (PATTERN 2)
MWI-155
< PRECAUTION >
C
D
E
F
G
H
I
J
K
L
M
B
N
A
O
P
PRECAUTION
AIR BAG (PATTERN 2)
Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT
PRE-TENSIONER"
INFOID:0000000000964455
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.
Information necessary to service the system safely is included in the SRS and SB section of this Service Man-
ual.
WARNING:
• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in
the event of a collision which would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.
• Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal
injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
Module, see the SRS section.
• Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or har-
ness connectors.
MWI-156
< ON-VEHICLE REPAIR >
COMBINATION METER
ON-VEHICLE REPAIR
COMBINATION METER
Exploded View
INFOID:0000000000964456
REMOVAL
Cluster lid A assembly
.
Combination meter
DISASSEMBLY
Removal and Installation
INFOID:0000000000964457
REMOVAL
JSNIA0098ZZ
1.
Cluster lid A
2.
Meter control switch
3.
Cluster lid A under cover
4.
Bracket (LH)
5.
Bracket (RH)
6.
Steering column cover upper
7.
Steering column blind
8.
Blind
9.
Meter housing
10. Combination meter stay
11. Combination meter
12. Cluster lid A cover
JSNIA0102ZZ
1.
Front cover
2.
Unified meter control unit
MWI
COMBINATION METER
MWI-157
< ON-VEHICLE REPAIR >
C
D
E
F
G
H
I
J
K
L
M
B
N
A
O
P
1.
Remove cluster lid A assembly. Refer to
IP-12, "Removal and Installation"
.
2.
Remove screw (A) and remove combination meter stay (1).
3.
Remove screws (B) and remove cluster lid A cover (2).
4.
Remove screws (A), (B) and remove combination meter (1).
5.
Remove meter control switch connector (2) from combination
meter (1).
INSTALLATION
Install in the reverse order of removal.
Disassembly and Assembly
INFOID:0000000000964458
DISASSEMBLY
Disengage the tabs to separate front cover.
ASSEMBLY
Assemble in the reverse order of disassembly.
JSNIA0100ZZ
JSNIA0101ZZ
MWI-158
< ON-VEHICLE REPAIR >
UNIFIED METER AND A/C AMP.
UNIFIED METER AND A/C AMP.
Exploded View
INFOID:0000000000964459
REMOVAL
.
DISASSEMBLY
Removal and Installation
INFOID:0000000000964460
REMOVAL
1.
Remove the display unit. Refer to
AV-112, "Removal and Installation"
.
2.
Remove the unified meter and A/C amp and AV control unit as an assembly.
3.
Remove the bracket screws and remove the unified meter and A/C amp.
INSTALLATION
Install in the reverse order of removal.
NOTE:
Unified meter and A/C amp. screws are different from other screws. Never confuse them when installing.
JSNIA0105ZZ
1.
Unified meter and A/C amp.
2.
Bracket (LH)
3.
AV control unit
4.
Bracket (RH)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст