Infiniti G35 (V35) Sedan. Manual — part 578
EC-458
< COMPONENT DIAGNOSIS >
[VQ35HR]
FUEL PUMP
FUEL PUMP
Description
INFOID:0000000000956868
*: ECM determines the start signal status by the signals of engine speed and battery voltage.
The ECM activates the fuel pump for several seconds after the ignition switch is turned ON to improve engine
startability. If the ECM receives a engine speed signal from the camshaft position sensor (PHASE), it knows
that the engine is rotating, and causes the pump to operate. If the engine speed signal is not received when
the ignition switch is ON, the engine stalls. The ECM stops pump operation and prevents battery discharging,
thereby improving safety. The ECM does not directly drive the fuel pump. It controls the ON/OFF fuel pump
relay, which in turn controls the fuel pump.
Component Function Check
INFOID:0000000000956869
1.
CHECK FUEL PUMP FUNCTION
1.
Turn ignition switch ON.
2.
Pinch fuel feed hose (1) with two fingers.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>>
.
Diagnosis Procedure
INFOID:0000000000956870
1.
CHECK FUEL PUMP POWER SUPPLY CIRCUIT-I
1.
Turn ignition switch OFF.
2.
Disconnect ECM harness connector.
3.
Turn ignition switch ON.
4.
Check the voltage between ECM harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> GO TO 2.
2.
CHECK FUEL PUMP POWER SUPPLY CIRCUIT-II
Sensor
Input signal to ECM
ECM Function
Actuator
Crankshaft position sensor (POS)
Camshaft position sensor (PHASE)
Engine speed*
Fuel pump control
Fuel pump relay
↓
Fuel pump
Battery
Battery voltage*
Condition
Fuel pump operation
Ignition switch is turned to ON.
Operates for 1 second.
Engine running and cranking
Operates.
When engine is stopped
Stops in 1.5 seconds.
Except as shown above
Stops.
Fuel pressure pulsation should be felt on the fuel feed
hose for 1 second after ignition switch is turned ON.
JMBIA0020ZZ
ECM
Ground
Voltage
Connector
Terminal
F101
22
Ground
Battery voltage
FUEL PUMP
EC-459
< COMPONENT DIAGNOSIS >
[VQ35HR]
C
D
E
F
G
H
I
J
K
L
M
A
EC
N
P
O
Check the voltage between IPDM E/R harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> GO TO 10.
3.
DETECT MALFUNCTIONING PART
Check the following.
• Harness connectors E3, F1
• Harness connectors F104, F105
• Harness for open or short between IPDM E/R and ECM
>> Repair open circuit or short to ground or short to power in harness or connectors.
4.
CHECK FUEL PUMP POWER SUPPLY CIRCUIT-III
1.
Turn ignition switch OFF.
2.
Reconnect all harness connectors disconnected.
3.
Disconnect “fuel level sensor unit and fuel pump” harness connector.
4.
Turn ignition switch ON.
5.
Check the voltage between “fuel level sensor unit and fuel pump” harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 8.
NO
>> GO TO 5.
5.
CHECK 15A FUSE
1.
Turn ignition switch OFF.
2.
Disconnect 15A fuse (No. 41) from IPDM E/R.
3.
Check 15A fuse.
Is the inspection result normal?
YES
>> GO TO 6.
NO
>> Replace fuse.
6.
CHECK FUEL PUMP POWER SUPPLY CIRCUIT-IV
1.
Disconnect IPDM E/R harness connector E5.
2.
Check the continuity between IPDM E/R harness connector and “fuel level sensor unit and fuel pump”
harness connector.
3.
Also check harness for short to ground and short to power.
Is the inspection result normal?
YES
>> GO TO 10.
NO
>> GO TO 7.
IPDM E/R
Ground
Voltage
Connector
Terminal
E7
77
Ground
Battery voltage
Fuel level sensor unit and
fuel pump
Ground
Voltage
Connector
Terminal
B22
1
Ground
Battery voltage should exist for 1 second
after ignition switch is turned ON.
IPDM E/R
Fuel level sensor unit
and fuel pump
Continuity
Connector
Terminal
Connector
Terminal
E5
13
B22
1
Existed
EC-460
< COMPONENT DIAGNOSIS >
[VQ35HR]
FUEL PUMP
7.
DETECT MALFUNCTIONING PART
Check the following.
• Harness connectors E104, B4
• IPDM E/R harness connector E5
• Harness for open or short between IPDM E/R and “fuel level sensor unit and fuel pump”
>> Repair open circuit or short to power in harness or connectors.
8.
CHECK FUEL PUMP GROUND CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect dropping resistor harness connector.
3.
Check the continuity between “fuel level sensor unit and fuel pump” harness connector and ground.
4.
Also check harness for short to power.
Is the inspection result normal?
YES
>> GO TO 9.
NO
>> Repair open circuit or short to power in harness or connectors.
9.
CHECK FUEL PUMP
EC-460, "Component Inspection"
Is the inspection result normal?
YES
>> GO TO 10.
NO
>> Replace fuel pump.
10.
CHECK INTERMITTENT INCIDENT
GI-39, "Intermittent Incident"
Is the inspection result normal?
YES
>> Replace IPDM E/R.
NO
>> Repair or replace harness or connectors.
Component Inspection
INFOID:0000000000956871
1.
CHECK FUEL PUMP
1.
Turn ignition switch OFF.
2.
Disconnect “fuel level sensor unit and fuel pump” harness connector.
3.
Check resistance between “fuel level sensor unit and fuel pump” terminals as follows.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Replace “fuel level sensor unit and fuel pump”
Fuel level sensor unit
and fuel pump
Ground
Continuity
Connector
Terminal
B22
3
Ground
Existed
Terminals
Resistance
1 and 3
0.2 - 5.0
Ω
[at 25
°
C (77
°
F)]
ICC BRAKE SWITCH
EC-461
< COMPONENT DIAGNOSIS >
[VQ35HR]
C
D
E
F
G
H
I
J
K
L
M
A
EC
N
P
O
ICC BRAKE SWITCH
Description
INFOID:0000000000956872
When the brake pedal is depressed, ICC brake switch is turned OFF and stop lamp switch is turned ON. ECM
detects the state of the brake pedal by this input of two kinds (ON/OFF signal).
Refer to
for the ICC function.
Component Function Check
INFOID:0000000000956873
1.
CHECK ICC BRAKE SWITCH FUNCTION
With CONSULT-III
1.
Turn ignition switch ON.
2.
Select “BRAKE SW1” in “DATA MONITOR” mode with CONSULT-III.
3.
Check “BRAKE SW1” indication under the following conditions.
Without CONSULT-III
1.
Turn ignition switch ON.
2.
Check the voltage between ECM harness connector and ground.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Go to
Diagnosis Procedure
INFOID:0000000000956874
1.
INSPECTION START
Check which type of transmission the vehicle is equipped with.
Which type of transmission?
A/T
>> GO TO 2.
M/T
>> GO TO 7.
2.
CHECK ICC BRAKE SWITCH POWER SUPPLY CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect ICC brake switch harness connector.
3.
Turn ignition switch ON.
4.
Check the voltage between ICC brake switch harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> GO TO 3.
3.
DETECT MALFUNCTIONING PART
Monitor item
Condition
Indication
BRAKE SW1
Brake pedal (A/T)
Brake pedal and clutch pedal (M/T)
Slightly depressed
OFF
Fully released
ON
ECM
Ground
Condition
Voltage
Connector
Terminal
M107
126
(ICC brake switch signal)
Ground
Brake pedal (A/T)
Brake pedal and clutch pedal (M/T)
Slightly depressed
Approx. 0V
Fully released
Battery voltage
ICC brake switch
Ground
Voltage
Connector
Terminal
E114
1
Ground
Battery voltage
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст